RTA Super EZ Sofa User manual

Seat Section Assembly
1
(2) 1/4”x 2-1/4” Clevis Pins
(2) 1/4”x 3” Clevis Pins
(2) 5/16”x 3-1/4” Clevis Pins
(2) Stop Pins
(6) Hair Pins
(30) Screws
(8) Wood Screws
FIRST: Be sure to correctly identify the 5 Seat Slats (holes are closer together and
will align with the faceplate) and the
5 Back Slats.
HARDWARE
ASSEMBLY
B.B.
B.B.
B. Position the (2) Back Legs as shown with Stop Pins pointing
in toward each other. Attach (3) Single-Hole and (2) Double-
Hole Back Slats to each Back Leg using (7) Screws per Leg.
AGAIN, DO NOT TIGHTEN.
Wheel
Seat Leg
Attach this Single-Hole Seat Slat LAST.
Faceplate
Hair
Pin
Seat Slats
Short
Clevis
Pin
Back Leg
Back Slats
Stop Pins
must face
inward and
opposite of
each other.
A.A.
A.A.
A. Position the two Seat Legs as shown. Using the hex
wrench provided, attach (3) Single-Hole and (2) Double-
Hole Seat Slats to each Seat Leg using (7) Screws per leg.
DO NOT TIGHTEN SCREWS YET.
C.C.
C.C.
C. Attach the (2) Plastic Wheels to the inside of each Seat Leg
by inserting a Short Clevis Pin thru the leg from the outside,
slip on the Wheel and secure with a Hair Pin.
B.B.
B.B.
B. Now attach Faceplate (shorter board) to the front of each
Seat Leg using (2) Screws.
Insert
Stop Pins
with slot
facing in
direction of
arrows.
Patent #5,170,519
ASSEMBLY
INSTRUCTIONS
(2) Wheels
(2) Washers
(1) Hex Wrench
(4) Edge Trim HelpfulHints: Theonlytoolsyouwill
needareaHammerandaPhillipsHeadScrew-
driver.Tomakeassemblyeasier,rubthethreads
ofthewoodscrewsonabarofsoap.Thisisa
carpenterístrickthatreallyworksgreat!
A.A.
A.A.
A. Lay the (2) Back Legs down
exactly as shown at left. Insert a
Stop Pin in each Back Leg,
positioning each so that the slot
in the Stop Pin faces in the direction
of the arrows. Use a hammer to fully
insert Pin (Pin should be flush with
other side of Leg).
Back Section Assembly
2
(2) Back Legs
(2) 1/4” x 2-1/2” Clevis Pins
2-1/2” Clevis Pin thru the leg from the outside,

Connecting the Frames
Connect the Seat and Back Sections by inserting
a Long Clevis Pin in from the outside, through
the Back Leg and then the slot in the Seat
Section. Secure with a Washer and a Hair Pin.
You may need to lift the front of the Seat Section
so the metal plate does not interfere. YOU MAY
NOW TIGHTEN ALL SCREWS SECURELY.
Attach Edge Trim
To convert back to a Bed
Lift Seat Section to engage Wheels, slide out and roll Back Section onto the floor. Push the Seat Section back a few
more inches (rotate it towards the Back Section). Lift Seat Section straight up and lower to the floor. If Section does
not disengage, the Seat is not rotated enough to clear the Stop
Pins or you are not
lifting and
holding
the Seat Section the full
distance allowed by the slot.
CONVERSIONS
280 Reese Road • State College, PA 16801 • [phone]
www.RTA-Furniture.com
NONO
NONO
NOTE:TE:
TE:TE:
TE: TIGHTEN ALL SCREWS UNTIL HEADS ARE FLUSH
WITH SLATS TO PREVENT INJURY OR FABRIC DAMAGE.
Make sure the Frame is square.
Take the flat side of an Edge Trim and hold against Slat ends. Shift
Frame slightly, if needed, until all Slat ends touch Edge Trim.
1
2
After squaring both the Seat and Back Sections, attach
Edge Trim as shown, using (2) Wood Screws for each.
A power drill is best here, but if done by hand using a
Phillips screwdriver remember to use a bar of soap to lubricate
the screws. Tighten all screw heads until they are flush.
TIP:TIP:
TIP:TIP:
TIP: BE SURE TO KEEP THE HEX WRENCH AS AN ADDITIONAL TIGHTENING
WILL BE REQUIRED DUE TO THE COMPRESSIBLE NATURE OF WOOD.
3
4
5
Edge Trim
WasherHair Pin
Seat Section
Back Section
To convert from Bed to Couch
Lift up Seat Section until it drops down and FULLY engages both Stop Pins.
Push down on the Seat
Section: this will bring
the Back up and put the
Wheels on the floor,
allowing you to roll the
Frame with ease.
Enjoy your new !
Long
Clevis Pin
A
BC
A
B
C
B
D
E
A
C