RTI Under Control XP-8 Operating instructions

1
It’s Under Control®
XP-8
Installation and Operation Guide
V 1.0
Advanced Control Processor
It’s Under Control®

Advanced Control Processor
XP-8
2
Copyright © 2007
Remote Technologies Incorporated
All rights reserved.

3
It’s Under Control®
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including
interference that may cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION NOTICE

Advanced Control Processor
XP-8
4
Read Instructions. Read all safety and operating instructions before
operating the unit.
Retain Instructions. Keep the safety and operating instructions for
future reference.
Heed Warnings. Adhere to all warnings on the unit and in the
operating instructions.
Follow Instructions. Follow operating instructions and instructions
for use.
Heat. Keep the unit away from heat sources such as radiators, heat
registers, stoves, etc., including ampliers that produce heat.
Power Sources. Connect the unit only to a power supply of the type
described in the operating instructions, or as marked on the unit.
Power Cord Protection. Route power supply cords so that they are
not likely to be walked on or pinched by items placed on or against
them, paying particular attention to the cords at plugs, at convenient
receptacles, and at the point at which they exit from the unit.
Water and Moisture. Do not use the unit near water—for example,
near a sink, in a wet basement, near a swimming pool, near an open
window, etc.
Object and Liquid Entry. Do not allow objects to fall or liquids to be
spilled into the enclosure through openings.
Servicing. Do not attempt any service beyond that described in
the operating instructions. Refer all other service needs to qualied
service personnel.
Damage Requiring Service. The unit should be serviced by qualied
service personnel when:
The power supply cord or the plug has been damaged.
Objects have fallen or liquid has been spilled into the unit.
The unit has been exposed to rain.
The unit does not appear to operate normally or exhibits a
marked change in performance.
The unit has been dropped or the enclosure has been damaged.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.
SAFETY SUGGESTIONS

5
It’s Under Control®
Remote Technologies Incorporated warrants its products for a period of one
(1) year from the date of purchase from Remote Technologies Incorporated
or an authorized Remote Technologies Incorporated distributor.
This warranty may be enforced by the original purchaser and subsequent
owners during the warranty period, so long as the original dated sales
receipt or other proof of warranty coverage is presented when warranty
service is required. Except as specied below, this warranty covers all
defects in material and workmanship in this product. The following are not
covered by the warranty:
Damage resulting from:
1. Accident, misuse, abuse, or neglect.
2. Failure to follow instructions contained in this Guide.
3. Repair or attempted repair by anyone other than Remote Technologies
Incorporated.
4. Failure to perform recommended periodic maintenance.
5. Causes other than product defects, including lack of skill, competence
or experience of user.
6. Shipment of this product (claims must be made to the carrier).
7. Being altered or which the serial number has been defaced, modied
or removed.
Remote Technologies Incorporated is not liable for any damages caused by
its products or for its failure of its products to perform, including any lost
prots, lost savings, incidental damages, or consequential damages.
Remote Technologies Incorporated is not liable for damages based upon
inconvenience, loss of use of the product, loss of time, interrupted
operation, commercial loss, any claim made by a third party or made by
you for a third party.
Remote Technologies Incorporated’s liability for any defective product is
limited to repair or replacement of the product, at our option.
If your XP-8 Processor needs service, please contact Remote Technologies
Incorporated by telephone, fax or E-mail for return information. Please do
not return products to Remote Technologies Incorporated without
return authorization.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated without the prior written notice of Remote
Technologies Incorporated.
The information contained in this document is subject to change without
notice. Remote Technologies Incorporated shall not be liable for errors or
omissions contained herein or for consequential damages in connection
with the furnishing, performance, or use of this guide.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other brands and their products are trademarks or registered trademarks
of their respective holders.
XP-8, It’s Under Control®, Integration Designer™, and the RTI logo are
registered trademarks of Remote Technologies Incorporated.
LIMITED WARRANTY AND DISCLAIMER

Advanced Control Processor
XP-8
6

7
It’s Under Control®
Federal Communications Commission Notice...............3
Safety Suggestions......................................................4
Limited Warranty and Disclaimer ...............................5
Contents......................................................................7
Chapter 1 - Welcome ...................................................9
Important Notes ...................................................... 9
Product Contents ................................................... 10
Chapter 2 - Features...................................................11
Front, Real Panels ................................................... 12
Programming ......................................................... 12
Chapter 3 - Installation ..............................................13
Freestanding or Rack Mount ..................................... 13
Chapter 4 - Connection Options..................................15
Rear I/O Ports ........................................................ 15
IR Emitters ............................................................ 16
Power Sensor Modules............................................. 16
Communication Modules .......................................... 16
RS-232 Ports.......................................................... 17
Sense Inputs.......................................................... 18
Relay/Trigger Inputs................................................ 18
Rear IR Connections................................................ 19
Infrared Receivers, RF Receivers, IR High Out............. 20
Ethernet, USB, RTI COM, Expansion Port.................... 21
Chapter 5 - Operation................................................. 23
Main Menu ............................................................. 25
Processing Rules..................................................... 29
Chapter 6 - Specications........................................... 31
Chapter 7 - Troubleshooting.......................................33
Chapter 8 - Service and Support.................................35
Index ......................................................................... 37
TABLE OF CONTENTS

Advanced Control Processor
XP-8
8

9
It’s Under Control®
Thank you for using the XP-8 Advanced Control Processor.
The XP-8 is a high-end remote control processor for automating the
operation of electronic systems in homes and ofce buildings. These
systems include home theaters, lighting, HVAC and many other
applications.
The combination of a blazing fast MPU, real-time/multitasking operating
system, and tremendous expandability make the XP-8 the perfect solution
for large scale and complex projects.
Like other RTI processors, the XP-8 has been designed to interface
seamlessly with all RTI remote controls and touchpanels. In addition to an
abundance of basic control ports such as infrared, contact closures, and
power sensors – the XP-8 provides advanced control interface options such
as two-way RS-232, USB, and Ethernet. An internet connection to the XP-8
allows convenient services such as updating system les and monitoring.
The XP-8 requires the Integration Designer™ programming software.
Before using the XP-8, please read and follow all of the instructions in this
guide.
IMPORTANT NOTES
Please read these important notes about the XP-8:
The XP-8 should be placed in an area where it is around normal
room temperature (between 50 F to 90 F).
Do not let the XP-8 get wet. It should not be handled with wet
hands or placed in an area where it could get wet.
Do not subject the XP-8 to smoke, dust, or vibrations.
Use only the power supply that is provided with the XP-8. Using
the wrong type of power supply may result in permanent damage.
Do not disassemble the unit. Service and repair should be
performed by an authorized technician only.
CHAPTER 1 | WELCOME

Advanced Control Processor
XP-8
10
Contents within the box include the following items:
One (1) XP-8 Remote Control Processor
One (1) Installation Guide
One (1) Universal Power Supply
One (1) Power Cord
Eight (8) IR Emitter Adapter Cables
Eight (8) RJ-45 (female) to DB-9 (male) Adapters for
dedicated RS-232 ports
Four (4) Removable Feet
Two (2) Rack Mounting Wings.
UNPACKING AND INSPECTION
After unpacking your new XP-8 Remote Control Processor, save all of the
packing materials in case you ever have to ship the unit.
Thoroughly inspect the XP-8 and packing materials for signs of damage.
Report any damage to the carrier immediately. Report any equipment
malfunctions to RTI or an authorized RTI distributor.
CHAPTER 1 | PRODUCT CONTENTS