RuggON MT7000 User manual

Front View
PACKAGE LIST
PRODUCT INTRODUCTION
Before you begin the installaon or conguraon process, make sure all the components and
accessories are intact. Contact your representave if any is missing or damaged. Please verify the
delivery of the contents upon receipt.
■MT7000 in-vehicle terminal
■Quick Start Guide
■Circular power connector to Fork Terminals (Length: 300mm)
■2-feet DB15 male connector cable with mulple end
■2-feet DB15 male connector cable (no terminaon)
NOTE: The packaging material provides opmal protecn to your device. Aer unpacking, DO store the
original packaging material in the event that you need to return for shipment.
PRODUCT INTRODUCTION
MT7000
Ambient light sensor
Display turn on/o
Volume
Power & Communicaon
LED indicators
Funcon buons Speaker
Speaker
The LEDs on MT7000 are status indicators that show the operang status of your system.
LED Status Description
Power Blink Yellow Load boot loader
Power Solid Green System ready to use
Power Blink Red Vehicle baery abnormal
Communicaon Solid Green WWAN enabled
The power management,


DashON.
The MT7000 supports a standard VESA version
MIS-D, 75, C (75mm distance quadrate order, M5
thread, deepness 6mm) with four mounng holes
on the back side of the device.
Rear View
Bo�om View
DC- in
GNSS(SMA Jack)
Oponal WWAN Antenna
Connector (SMA Jack)
Oponal Wi-Fi/BT Antenna
Connector (SMA Jack)
RS-232(COM1) with 5/12V power output
USB, RS - 232/422/485 (COM2)
LAN
DIO/ CAN bus
Side View
SIM Card Slot
Micro SD Card Slot
Headset jack
Reset buon
USB Type A
LED Status Description
Power Blink Green Power up
MT7000
Mobile Data Terminal
Quick Start Guide
P/N: 25U100014-001


Wire Color Description
RED V+
BLACK V-
GREEN PE (Safety Ground)
WHITE ACC/ Ignion
POWERING ON THE SYSTEM CONNECTOR PIN ASSIGNMENTS
MT7000 allows a wide range of DC power input from 9~36V via a 3-pin circular power cord.
There are two opons to start up the MT7000, either via car power cable or external power
adapter.
Fuse Requirements
Fuses* are required in connecng the
power cable and bery in series and add
3A fuse in ACC/ignion line to avoid the
risks of wire damage and vehicle burning.
For detailed power wiring diagram, please
refer to the Powering the System secon
of Chapter 4 in MT7000’s user manual.
Make sure that all power supplies are
disconnected when you plug the
power cord into the power connector.
1. The bare wire lead cable lets you directly wire to 12V or 24V car power supply.
2. Please refer to the wire denion below for connecng your power source.
Power on through external power adapter
Please connect red (V+) wire to white (ACC/ Ignion) wire to power on MT7000 through an
external power adapter. ACC/Ignion mode is not supported in such condion.
Notes:
* 5A for 24VDC power input
* 10A for 12VDC power input
MT7000 P/N: 25U100014-001
Power Connector
Pin Description
1 DC+
2 GND
3 ACC/ Ignon
USB and RS-232/422/485 Port (COM2)
Pin Description Pin Description
1 RS-422 TX+ 9 USB 5V
2 RS-422 RX+ 10 RS-232 RX
3 RS-485 TX+ 11 GND
4 RS-232 TX 12 USB DP
5 GND 13 USB DM
6 RS-422 TX- 14 USB 5V
7 RS-422 RX- 15 NC
8 RS-485 TX-
DIO and CAN bus Port
Pin Description Pin Description
1 CAN_H 9 CARD POWER
2 N/A 10 GND
3 N/A 11 SOS
4 N/A 12 DIO_OUT1 (5V 10mA)
5 N/A 13 DIO_IN1 (5V 100mA)
6 CAN_L 14 DIO_IN2 (5V 100mA)
7 N/A 15 DIO_OUT2 (5V 10mA)
8 N/A
Red
Green
Black
White
Lines to

Safety
Ground
5A/10A
FUSE 3A
FUSE
1
5
15 11
1
5
15 11
2
13