RuggVMC ruggon VIKING User manual

[鍵入文字]
VIKING
Mobile Data Terminal
Quick Start Guide
Front View
LED
Status
Description
Power
Blink Green
Power up
Power
Blink Yellow
Load boot loader
Power
Solid Green
System ready to use
Power
Blink Red
Vehicle battery abnormal
Communication
Solid Green
WWAN enabled
Please note power management, I/O configuration, and button settings can be
configured in Android SettingSystemAdvanced. No DashON support in
VIKING.
Product Introduction
Rear View
Bottom View
Side View
Product Introduction
Notes: To prevent any damage or injury, make sure the mounting bracket is securely attached.
The VIKING supports a standard VESA
version MIS-D, 75, C (75mm distance
quadrate order, M5 thread, deepness
6mm) through the four drill holes on the
back side of the device.
The LEDs on VIKING are status indicators that show the operating status of your system.
P/N: 25-13658-01
Ambient light sensor
Power
Volume
Power & Communication
LED indicators
Camera
(optional)
Function buttons
USB Type-C DP Alt Mode
RS-232(COM1) with 5/12V power output
USB, RS-232/422/485(COM2)
LAN
DIO / CANbus
Optional WWAN Antenna Conn. (SMAjack)
GNSS
(SMA jack)
DC-in
SIM Card Slot
Micro SD Card Slot
Audio jack
Reset button
Optional Wi-Fi/BTAntenna Conn.
(SMA jack)
Speaker
1st internal Microphone
2nd internal Microphone
Speaker
Model: MT7030
Built-in RFID/ NFC reader

[鍵入文字]
VIKING allows a wide range of DC power input from 9~36V via a 5-pin M12 A-code
power cord. There are two options to start up the VIKING, either via car power cable or
external power adapter.
Fuses 10A are required in connecting the power cable and battery in series to
avoid the risks of wire damage and vehicle burning. About the diagram of power wiring,
please refer to the Powering the System section under Chapter 4 in VIKING’s user
manual.
Power source from car power cable
Make sure that all power supplies are disconnected when you plug the
power cord into the power connector.
1. The bare wire lead cable allows you to directly wire 12 V or 24 V car power supply.
2. Please follow the wire definition to connect to your power source.
Wire Color
Description
RED
V+
BLACK
V-
GREEN
PE (Safety Ground)
WHITE
ACC/ Ignition
Power source from external power adapter
If your power source is from external power adapter, it means the power source isn’t
controlled by ACC/Ignition signal. Please short red (V+) and white (ACC/ Ignition) wires.
Powering the System
USB and RS-232/422/485 Port (COM2)
Pin
Description
Pin
Description
1
RS-422 TX+
9
USB 5V
2
RS-422 RX+
10
RS-232 RX
3
RS-485 TX+
11
GND
4
RS-232 TX
12
USB DP
5
GND
13
USB DM
6
RS-422 TX-
14
USB 5V
7
RS-422 RX-
15
NC
8
RS-485 TX-
We provide Y-cable with DB15 male connector which is the RS-232/422/485 and USB
converter. Please contact your local sales representative for ordering information.
DIO and CAN bus Port
Pin
Description
Pin
Description
1
CAN_H
9
N/A
2
N/A
10
N/A
3
N/A
11
SOS
4
ISO_GND
12
DIO_OUT1
5
N/A
13
DIO_IN1
6
CAN_L
14
DIO_IN2
7
N/A
15
DIO_OUT2
8
N/A
We provide the DB15 male connector to multiple pins without termination cable. Please
contact your local sales representative for ordering information.
Connector Pin Assignments
Power Connector
Pin
Description
1
DC+
2
DC+
3
GND
4
GND
5
ACC/ Ignition
Connector Pin Assignments
1
2
3
4
5
P/N: 25-13658-01
Model: MT7030