Ruijie Networks RG-EasyGate Series Assembly instructions

RG-EasyGate Series Hardware Installation Guide V1.28
Hardware Installation Manual
RG-EasyGate Series Products

RG-EasyGate Series Hardware Installation Guide V1.28
Copyright Statement
Ruijie Networks©2000-2013
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any
means, without the prior written consent of Ruijie Networks is prohibited.
, , , ,
, ,
, , , ,
, are registered trademarks of Ruijie Networks. Counterfeit is
strictly prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please
obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content
accuracy and will not shoulder any responsibility for losses and damages caused by content omissions, inaccuracies
or errors.

RG-EasyGate Series Hardware Installation Guide V1.28
Preface
Version Description
This manual applies to EG series RG-EG1000C, RG-EG1000CM, RG-EG1000S, RG-EG1000L and RG-EG1000M
gateways of Ruijie Networks.
Readers
This manual is suitable for the following readers:
Network engineer
Technology promotion personnel
Network administrator
Introduction
This manual mainly introduces the hardware characteristics, installation configuration, maintenance and troubleshooting
of Ruijie EG series gateways. Before and during product installation, please read this manual carefully to avoid potential
device damage and physical injury.
This manual includes the following chapters:
Chapter 1 "Product Overview"
Describes product appearance and system characteristics of Ruijie EG Series gateway.
Chapter 2 "Preparation before Installation"
Describes environmental requirements for gateway installation, precautions before and during installation, and tools
needed.
Chapter 3 "Installing the Breakout Gateway"
Describes mechanical installation, power supply connection, and console port cable connection of Ruijie EG series
breakout gateway.
Chapter 4 "Starting and Configuring the Breakout Gateway"
Describes the initial startup information and initial configuration of breakout gateway;
Chapter 5 "Troubleshooting"
Introduces possible faults and troubleshooting during the installation process.

RG-EasyGate Series Hardware Installation Guide V1.28
Note
This installation manual only introduces how to install Ruijie EG series breakout gateway and the configuration guide of
some commonly used functions. To further configure the breakout gateway, refer to the configuration guide and command
reference document contained in the attached CD.
In this manual, Ruijie RG-EGxxx series breakout gateways are abbreviated as Ruijie EGxxx breakout gateway.
Detailed descriptions and configurations shall be subject to the CD attached. Ruijie may revise this manual without further
notice.
Installation and configuration of this device shall be carried out by a specialized technical personnel being familiar with
electrical environment and cable connection and being experienced in breakout gateway installation and configuration.

RG-EasyGate Series Hardware Installation Guide V1.28
Product Overview
Ruijie EG series breakout gateway employs the global-leading semiconductor technologies and communication control
technologies, and is an independently developed data communication product of Ruijie Networks with independent
intellectual property right. The breakout gateway products of Ruijie are completely developed as per international
standards and are similar to the mainstream breakout gateway products in the international market. By reading this
manual, network administrator being familiar with mainstream breakout gateway configuration commands can easily use
this product without training.
Ruijie EG Series Breakout Gateways
Ruijie EG1000L Breakout Gateway
Appearance of Ruijie EG1000L Breakout Gatgeway
Figure 1-1 Front Panel of Ruijie EG1000L Breakout Gateway
Figure 1-2 Backpanel of Ruijie EG1000L Breakout Gateway
Basic Configuration of Ruijie EG1000L Breakout Gateway
Table 1-1 Basic Configuration of Ruijie EG1000L V1.0 Breakout Gateway
Item Description
DDR2 SDRAM: 512 MB
BOOTROM: 8 MB
Storage
FLASH: 128 MB
Supports 24 100 MB switching ports and automatic recognition of
network cables and cross-over cables.
Supports two Gigabit Ethernet copper ports, two SFP optical ports and
automatic recognition of network cables and cross-over cables. (The
Gigabit Ethernet copper port and the SPF optical port are fiber/copper
combo ports.) Each optical port supports 1000BASE-SX/LX/ZX mini
GBIC optical module.
I/O Setup
One console port.

RG-EasyGate Series Hardware Installation Guide V1.28
One USB port.
One reset button (RESET), which is on the right side of the serial port.
LED Indicators There are seven LED indicators: PWR, SYS, USB, GE1, GE2, SFP1
and SFP2.
Interface Standard Ethernet: 10Base-T/100Base-TX/1000Base-TX, 1000BASE-SX/LX/ZX
Configuration port (console port): RS-232
Dimension (W x H x D) 440 x 43.6 x 200 mm (excluding the foot pad)
Voltage 100–240 V; 50–60 Hz
Power Consumption Less than 35 W
Temperature: 0°C to 50°C
Working Environment Humidity: 10% to 90% RH (non-condensing)
Since there are numerous types of U-disk, we cannot ensure that the system supports all of them. The
Kingston U-disk with FAT 32 are recommended to be used.
LED Indicators of Ruijie EG1000C Breakout Gateway
Table 1-2 LED Indicators of Ruijie EG1000L V1.0 Breakout Gateway
LED Indicators Working Status
PWR Solid green indicates the power supply is working properly.
SYS
Blinking green indicates the system is being initialized.
Solid green indicates system initialization has completed.
Solid red indicates system warning.
USB Solid green indicates the USB disk is inserted.
Blinking green indicates data reading/writing.
0-23 Solid green indicates the link that the port connects to is up.
Blinking green indicates data is being transceived at the port.
GE0/1, GE0/2
Solid green indicates the 1000 M link that the port connects to is up.
Blinking green indicates data at a rate of 1000 M is being transceived at
the port.
Solid orange indicates the 10 M/100 M link that the port connects to is
up.
Blinking orange indicates data at a rate of 10 M/100 M is being
transceived at the port.
SFP1, SFP2 Solid green indicates the link that the port connects to is up.
Blinking green indicates data is being transceived at the port.
Reset Button
To reset the breakout gateway system, press this button for less than
three seconds.
To restore the breakout gateway to default settings and reset the
system, press this button for more than three seconds.

RG-EasyGate Series Hardware Installation Guide V1.28
Ruijie EG1000-CM Breakout Gateway
Appearance of Ruijie EG1000-CM Breakout Gateway
Figure 1-3 Front Panel of Ruijie EG1000-CM Breakout Gateway
Figure 1-4 Backpanel of Ruijie EG1000-CM Breakout Gateway
Basic Configuration of Ruijie EG1000-CM Breakout Gateway
Table 1-3 Basic Configuration of Ruijie EG1000-CM Breakout Gateway
Item Description
DDR2 SDRAM: 512 MB
BOOTROM: 8 MB
FLASH: 128 MB
Storage
Mass Storage: 8 GB
WAN port: two default 10/100/1000 M self-adaptive fast Ethernet copper
ports (0/5, 0/6), automatic recognition of network cables and cross-over
cables. Each WAN port is fiber/copper combo port and supports
1000BASE-SX/LX/ZX mini GBIC optical module.
LAN port: five default 10/100/1000 M self-adaptive fast Ethernet copper
ports (0/0, 0/1, 0/2, 0/3, 0/4), automatic recognition of network cables
and cross-over cables.
All Ethernet ports can be switched between WAN mode and LAN mode.
Management port: one management port (in bridge mode)
I/O Setup
One console port, one USB port and one SD card.
BYPASS
Hardware BYPASS: 0/3-0/5, 0/4-0/6;
Supports the two modes of power-off, power-on BYPASS and the main
program configured BYPASS
Interface Standard Ethernet: 10Base-T/100Base-TX/1000Base-TX, 1000BASE-SX/LX/ZX
Configuration port (console port): RS-232
Dimension (W x H x D) 440 x 43.6 x 200 mm (excluding the foot pad)
Voltage 100–240 V; 50–60 Hz
Power Consumption Less than 30 W
Temperature: 0°C to 45°C
Working Environment Humidity: 10% to 90% RH (non-condensing)

RG-EasyGate Series Hardware Installation Guide V1.28
Since there are numerous types of U-disk and SD cards, we cannot ensure that the system supports all of
them. The Kingston 2G SD card and the 2G U-disk with FAT 32 are recommended to be used.
For the RG EG1000-CM product has the built-in hard disk, please avoid the vibration and collision in the
process of moving and usage.
When the EG series hosts are in hardware BYPASS mode, the two Ethernet ports connecting with the pair of
BYPASS ports of the EG series products are directly connected via network cables actually. As a result,
prevent them from being in the same VLAN to avoid broadcast storm.
LED Indicators of Ruijie EG1000-CM Breakout Gateway
Table 1-4 LED Indicators of Ruijie EG1000-CM Breakout Gateway
LED Indicators Working Status
PWR Solid green indicates the power supply is working properly.
Off indicates the power supply is off or the power supply is faulty.
SYS
Blinking green indicates the system is being initialized.
Solid green indicates system initialization has completed.
Solid red indicates system warning.
SATA Solid green indicates the SATA hard disk is inserted.
Blinking green indicates data reading/writing.
SD Solid green indicates the SD card is inserted.
Blinking green indicates data reading/writing.
USB Solid green indicates the USB disk is inserted.
Blinking green indicates data reading/writing.
Link/ACT Indicators of
0-6 Copper Ports
Solid green indicates the 10/100/1000 M link that the port connects to is
up.
Blinking green indicates data is being transceived at the port.
Speed Indicators of 0-6
Copper Ports
Solid orange indicates data at a rate of 1000 M is being transceived at
the port.
Off indicates data at a rate of 10 M or 100 M is being transceived at the
port.
Optical port indicators
of 5F-6F Gigabit Ports
Solid green indicates the link that the port connects to is up.
Blinking green indicates data is being transceived at the port.
Ruijie EG1000C Breakout Gateway
Appearance of Ruijie EG1000C Breakout Gateway
Figure 1-5 Front Panel of Ruijie EG1000C Breakout Gateway

RG-EasyGate Series Hardware Installation Guide V1.28
Figure 1-6 Backpanel of Ruijie EG1000C Breakout Gateway
Basic Configuration of Ruijie EG1000C Breakout Gateway
Table 1-5 Basic Configuration of Ruijie EG1000C Breakout Gateway
Item Description
DDR2 SDRAM: 1 GB
BOOTROM: 8 MB
FLASH: 128 MB
Storage
SATA Hard Disk: 320 GB
WAN port: two default 10/100/1000 M self-adaptive fast Ethernet copper
ports (0/5, 0/6), automatic recognition of network cable and cross-over
cable. Each WAN port is fiber/copper combo port and supports
1000BASE-SX/LX/ZX mini GBIC optical module.
LAN port: five default 10/100/1000 M self-adaptive fast Ethernet copper
ports (0/0, 0/1, 0/2, 0/3, 0/4), automatic recognition of network cables
and cross-over cables.
All Ethernet ports can be switched between WAN mode and LAN mode.
Management port: one management port (in bridge mode)
I/O Setup
One console port, one USB port and one SD card.
BYPASS
Hardware BYPASS: 0/3-0/5, 0/4-0/6;
Supports the two modes of power-off, power-on BYPASS and the main
program configured BYPASS
Interface Standard Ethernet: 10Base-T/100Base-TX/1000Base-TX, 1000BASE-SX/LX/ZX
Configuration port (console port): RS-232
Dimension (W x H x D) 440 x 43.6 x 200 mm (excluding the foot pad)
Voltage 100–240 V; 50–60 Hz
Power Consumption Less than 30 W
Temperature: 0°C to 45°C
Working Environment Humidity: 10% to 90% RH (non-condensing)
Since there are numerous types of U-disk and SD cards, we cannot ensure that the system supports all of
them. The Kingston 2G SD card and the 2G U-disk with FAT 32 are recommended to be used.

RG-EasyGate Series Hardware Installation Guide V1.28
For the RG-EG1000C product has the built-in hard disk, please avoid the vibration and collision in the
process of moving and usage.
When the EG series hosts are in hardware BYPASS mode, the two Ethernet ports connecting with the pair of
BYPASS ports of the EG series products are directly connected via network cables actually. As a result,
prevent them from being in the same VLAN to avoid broadcast storm.
LED Indicators of Ruijie EG1000C Breakout Gateway
Table 1-6 LED Indicators of Ruijie EG1000C Breakout Gateway
LED Indicators Working Status
PWR Solid green indicates the power supply is working properly.
Off indicates the power supply is off or the power supply is faulty.
SYS
Blinking green indicates the system is being initialized.
Solid green indicates system initialization has completed.
Solid red indicates system warning.
SD Solid green indicates the SD card is inserted.
Blinking green indicates data reading/writing.
SATA Solid green indicates the SATA hard disk is inserted.
Blinking green indicates data reading/writing.
USB Solid green indicates the USB disk is inserted.
Blinking green indicates data reading/writing.
Link/ACT Indicators of
0-6 Copper Ports
Solid green indicates the 10/100/1000 M link that the port connects to is
up.
Blinking green indicates data is being transceived at the port.
Speed Indicators of 0-6
Copper Ports
Solid orange indicates data at a rate of 1000 M is being transceived at
the port.
Off indicates data at a rate of 10 M or 100 M is being transceived at the
port.
Optical port indicators
of 5F-6F Gigabit Ports
Solid green indicates the link that the port connects to is up.
Blinking green indicates data is being transceived at the port.
Ruijie EG1000S Breakout Gateway
Appearance of Ruijie EG1000S Breakout Gateway
Figure 1-7 Front Panel of Ruijie EG1000S Breakout Gateway
Figure 1-8 Backpanel of Ruijie EG1000S Breakout Gateway

RG-EasyGate Series Hardware Installation Guide V1.28
Basic Configuration of Ruijie EG1000S Breakout Gateway
Table 1-7 Basic Configurations of Ruijie EG1000S Breakout Gateway
Item Description
DDR2 SDRAM: 2 GB
BOOTROM: 2 MB
FLASH: 512 MB
Storage
SATA Hard Disk: 320 GB
Supports gateway mode (default) and bridge mode.
WAN port: four default 10/100/1000 M self-adaptive fast Ethernet ports,
automatic recognition of network cables and cross-over cables. The 0/1
port can also be used as an optical port, which supports the
1000BASE-SX/LX/ZX mini GBIC optical module.
LAN port: two default 10/100/1000 M self-adaptive fast Ethernet ports,
automatic recognition of network cable and cross-over cable.
All Ethernet ports can be switched between WAN mode and LAN mode.
Management port: one management port (in bridge mode)
I/O Setup
One console port
BYPASS
Hardware BYPASS: 0/0-0/1, 0/3-0/4
Supports the two modes of power-off, power-on BYPASS and the main
program configured BYPASS.
Ethernet: 10Base-T/100Base-TX/1000Base-TX,
1000BASE-SX/LX/ZX
Interface standard
Configuration port (console port): RS-232
Dimension (W x H x D) 440 x 43.6 x 400 mm (excluding the foot pad)
Voltage 100–240 V; 50–60 Hz
Power Consumption Less than 50 W
Temperature: 0°C to 50°C
Working Environment Humidity: 10% to 90% RH (non-condensing)
Since there are numerous types of U-disk and SD cards, we cannot ensure that the system supports all of
them. The Kingston 2G SD card and the 2G U-disk with FAT32 are recommended to be used.
For the RG-EG1000S product has the built-in hard disk, please avoid the vibration and collision in the
process of moving and usage.

RG-EasyGate Series Hardware Installation Guide V1.28
When the EG series hosts are in hardware BYPASS mode, the two Ethernet ports connecting with the pair of
BYPASS ports of the EG series products are directly connected via network cables actually. As a result,
prevent them from being in the same VLAN to avoid broadcast storm.
LED Indicators of Ruijie EG1000S Breakout Gateway
Table 1-8 LED Indicators of Ruijie EG1000S Breakout Gateway
LED Indicators Working Status
PWR Solid green indicates the power supply is working properly.
SYS Solid green indicates system normality.
Solid yellow indicates system abnormity.
SD Solid green indicates the SD card is inserted.
Blinking green indicates data reading/writing.
SATA Solid green indicates the SATA hard disk is inserted.
Blinking green indicates data reading/writing.
USB Solid green indicates the USB disk is inserted.
Blinking green indicates data reading/writing.
1F Solid green indicates the link that the optical port connects to is up or
data is being transceived at the port.
0, 1, 2, 3, 4, 5/MGMT Solid green indicates the link that the port connects to is up.
Blinking green indicates data is being transceived at the port.
Reset Button
To reset the breakout gateway system, press this button for less than 3
seconds.
To restore the breakout gateway to default settings and reset the
system, press this button for more than 3 seconds.
Ruijie EG1000M Breakout Gateway
Appearance of Ruijie EG1000M Breakout Gateway
Figure 1-9 Front Panel of Ruijie EG1000M Breakout Gateway
Figure 1-10 Backpanel of Ruijie EG1000M Breakout Gateway

RG-EasyGate Series Hardware Installation Guide V1.28
Basic Configuration of Ruijie EG1000M Breakout Gateway
Table 1-9 Basic Configuration of Ruijie EG1000M Breakout Gateway
Item Description
DDR2 SDRAM: 4 GB
BOOTROM: 8 MB
FLASH: 512 MB
Storage
SATA Hard Disk: 320 GB
Gigabit Ethernet interface:
Supports 8 pairs of fiber/copper combo ports and all of them
can be switched between the WAN mode and LAN mode. By
default, the interface 0/1, 0/3, 0/5, 0/7 are WAN ports, while the
interface 0/0, 0/2, 0/4, 0/6 are LAN ports.
The copper ports are 10/100/1000 M adaptive and support
automatic recognition of the network cables and the cross-over
cables.
The fiber ports are supported on the 1000BASE-SX/LX/ZX mini
GBIC module.
One management port, which supports 10/100 M adaptive and
automatic recognition of the network cables and the cross-over
cables.
One console port
One USB port
I/O Setup
One SD card
BYPASS
Gigabit copper port hardware BYPASS:
Supports two pairs of the interfaces: 0/0-0/1 and 0/2-0/3;
Supports the two modes of power-off, power-on BYPASS and
the main program configured BYPASS.
Supports fiber BYPASS. (you need to purchase the fiber
BYPASS device.)
Switch Power Module Supports two RG-PA300I power modules.
Hot-swapping Supports fan tray hot swapping.
Supports power supply hot swapping.
Interface Standard
Ethernet: 10Base-T/100Base-TX/1000Base-TX,
1000BASE-SX/LX/ZX
Configuration port (console port): RS-232
Dimension (W x H x D) 440 x 88.1 x 420 mm (excluding the foot pad)

RG-EasyGate Series Hardware Installation Guide V1.28
Voltage 100–240 V; 50–60 Hz
Power Consumption Less than 100 W
Temperature: 0°C to 45°C
Working Environment Humidity: 10% to 90% RH (non-condensing)
Since there are numerous types of U-disk and SD cards, we cannot ensure that the system supports all of
them. The Kingston 2G SD card and 2G U-disk with FAT32 are recommended to be used.
For the RG-EG1000M product has the built-in hardware disk, please avoid the vibration and collision in the
process of moving and usage.
When the EG series hosts are in hardware BYPASS mode, the two Ethernet ports connecting with the pair of
BYPASS ports of the EG series products are directly connected via network cables actually. As a result,
prevent them from being in the same VLAN to avoid broadcast storm.
LED Indicators of Ruijie EG1000M Breakout Gateway
Table 1-10 LED Indicators of Ruijie EG1000M Breakout Gateway
LED Indicator Working status
PWR1, PWR2
Solid green indicates the power module is installed.
Off indicates the power module is not installed.
Solid red indicates the power module is faulty or not powered on.
SYS
Blinking green indicates the system is being initialized.
Solid green indicates system initialization has completed.
Solid red indicates system warning.
Fan
Solid green indicates the fan is installed.
Off indicates the fan is not installed.
Solid red, blinking red or blinking green indicates the fan is faulty.
SD Solid green indicates the SD card is inserted.
Blinking green indicates data reading/writing.
SATA Solid green indicates the SATA hard disk is inserted.
Blinking green indicates data reading/writing.
USB Solid green indicates the USB disk is inserted.
Blinking green indicates data reading/writing.
Link Indicator of the
Management Port. Solid green indicates the link that the port connects to is up.
ACT Indicator of the
Management Port Blinking orange indicates data is being transceived at the port.
Indicators of 0-7 Gigabit Solid green indicates the 1000 M link that the port connects to is up.

RG-EasyGate Series Hardware Installation Guide V1.28
Copper Indicators Solid orange indicates the 10 M/100 M link that the port connects to is
up.
Blinking indicates data is being transceived at the port.
Indicators of 0F-7F Gigabit
Optical Ports
The green in-position LED is on when the optical module is inserted.
Solid green indicates the link that the port connects to is up.
Blinking green indicates data is being transceived at the port.
BYPASS Indicators of the
OBS0, OBS1 Optical port
Solid green indicates the power supply is working.
Off indicates no power supply.
Power Modules
RG-PA300I Power Module
Module Appearance and Indicators
Figure 1-11 Appearance of the RG-PA300I Power Module
Table 1-11 Indicator Description of the RG-PA300I Power Module
LED Indicator Working Status
IN Solid green indicates normal power input.
Off indicates abnormal power input.
OUT Solid green indicates normal power output
Off indicates abnormal power output.
FAIL Off indicates the power supply is working properly.
Solid red indicates the abnormal power supply.
Module Attributes
Table 1-12 Attribute Description of the RG-PA300I Power Module
Attributes Description
Rated Input Value 100–240 V; 50–60 Hz; 6.5 A
Rated Output Value 12 V: 1–25 A
12 V FAN: 0–5 A
Rated Output Power 300 W
Hot Swapping Supported
N+1 Backup Supported
Power Factor Correction (PFC) Supported
Protection Features
Input over-voltage and under-voltage protection, output
over-voltage protection, over-current protection, short-circuit
protection and over-temperature protection.
Communication Features Supports to communicate with the host to obtain information

RG-EasyGate Series Hardware Installation Guide V1.28
about power temperature and output power.
It is worth mentioning that the power temperature range is
-5ºC–+50ºC (±2ºC). The temperature value would be incorrect if
it is beyond that range.
Features of Ruijie EG Series Breakout Gateway
Full Support to Extensive Protocols
Ruijie EG series breakout gateway is applicable to different network environment as it provides full support to
extensive protocols:
Providing RJ45 port and supporting Ethernet protocol and ARP protocol;
Supporting TCP/IP protocol stack at the network layer (IP, ICMP, IGMP, TCP, UDP and so on);
Supporting multiple IP-based dynamic routing protocol such as RIP (V1/V2), OSPF;
Supporting the network management protocol of SNMP;
Supporting TELNET;
Supporting DHCP;
Supporting PPPoE;
Supporting asynchronous file transfer protocol of X-MODEM;
Supporting NAT;
Supporting policy-based routing;
Supporting VRRP;
Supporting L2TP and PPTP;
Supporting TFTP.
Friendly User Interface
The standard operation interface allows visual configuration, and each command is accompanied by detailed online
help;
The user manual contains detailed explanation and demonstration of each command, and provides comprehensive
fault analysis;
Both the WEB configuration interface and the standard CLI configuration interface are provided, reducing the costs
of study and usage and bringing convenience to maintenance.
Abundant Diagnosis and Management Tools
Comprehensive debugging and tracking commands are provided, allowing convenient and precise location of
various network faults.
Complete statistics and status information display functions are provided, enabling user to have a clear knowledge of
network performance and operating status.
Supporting multiple terminal login and configuration modes, such as configuration via the console port, login and
configuration via TELNET, and configuration via the TFTP server.

RG-EasyGate Series Hardware Installation Guide V1.28
Excellent Security
Adopting the perfect firewall and IP packet filtering technology to implement rigid checking of network address, port
number or protocol type.
PAP and CHAP protocol over PPP protocol.
Supporting MAC address binding.
Supporting Network Address Translation (NAT).
Professional Flow Control
The gateway product adopts the new-generation DPI engine developed by Ruijie Networks, and is capable of
precisely recognizing over 600 protocols including P2P, IM, stock application, stream media, officing and online
gaming.
Real-time acquisition, monitoring and precise analysis of network flow, achieving the visualization of network
operation status, application status and bandwidth usage status. Protocol-based and user-based real-time flow
analyzer provides detailed information on source/destination IP address, service port, application protocol, session
number and flow size.
Supporting user (source IP address), destination IP address, time, protocol and application based flexible blocking
and permitting, including: outbound and inbound bandwidth control, session number control and so on.
Supporting group object configuration, such as the configuration of user group (IP group) and protocol group (such
as P2P protocol group and gaming group), as well as the bandwidth management policy based control of users of
the same level and with the same type of application.
URL Filtering and Auditing
The independently developed Chinese URL database: The independently developed URL system will constantly
collect URL information, and the URL database of Ruijie Networks is divided into 41 categories, with 6 million entries
covering almost all websites in Mainland China.
Supporting user (source IP address), URL classification and time based flexible blocking and permitting of URL
accesses of intranet users.
Supporting user (source IP address), URL classification and time based real-time auditing of URL accesses of
intranet users and flexible query of audit content.
Easy Upgrade
Supporting asynchronous file transfer protocol of X-MODEM, allowing the user to download new versions of upgrade
software through Console port under various operating systems (such as Windows 95, Windows NT, UNIX, and
DOS).
Downloading new versions of software via TFTP protocol.
Online upgrade of BOOTROM.
Supporting automatic upgrade and upgrade via Web.
High Reliability in Software and Hardware.
Supporting bridge mode, routing mode, bypass mode and other deployment modes, meeting the need for
deployment in various contexts.

RG-EasyGate Series Hardware Installation Guide V1.28
The transparent bridging does not change the configurations of other devices, allowing complete URL filtering, flow
control and content auditing.
The bypass mode ensures that the network is free from single point failure and will not affect network performance.
Built-in hardware BYPASS guarantees uninterrupted forwarding in case of power failure, device reboot and other
abnormal circumstances.

RG-EasyGate Series Hardware Installation Guide V1.28
Preparations before Installation
Safety Precautions
The breakout gateway acts as the critical transfer station of network connections, and its normal service is crucial to the
normal operation of the entire network.
The following safety suggestions are applicable to the installation and use of the breakout gateway:
Do not place the device in a watery place and prevent any liquid from entering into it.
Keep the device away from heat sources.
Ensure the normal grounding of device.
Wear an anti-static wrist strap to install and maintain the device.
Do not wear loose clothes to avoid hooking any parts. Before operation, tighten your band, shawl and sleeves.
Keep tools and parts away from the walkway to avoid damage.
Use the uninterruptible power supply (UPS) to avoid power failure and other interferences.
If the system time is incorrect, check whether you have set the clock. If the clock is not set, the time may not be correct; if
the clock has been set precisely and the time is still incorrect, the built-in button cell of device may have ran out, which is
typically happened after 10-year service.
Install and use the device in restricted access locations.
Use of wrong battery may cause damage to the device. Do not replace the battery by yourself. Please contact the
Customer Service Department of Ruijie Networks for help.
Invite professionals and related technicians to install this type of device.
This is a Class-A product which may cause radio interference in the living environment. In such a case, the user may need
to take feasible measures against such interference.
Requirements on Installation Environment
Ruijie EG series breakout gateway products are for indoor use only. To ensure normal operation and prolong their service
life, the installation site must meet the following requirements:
Temperature/humidity requirements
Cleanliness requirements
Anti-static requirements
Anti-interference requirements
Lightning protection requirements
Checking the installation location

RG-EasyGate Series Hardware Installation Guide V1.28
Temperature/Humidity Requirements
To ensure normal operation and prolong the service life of the device, the equipment room must maintain constant
temperature and humidity. If the equipment room is overheated for a long time, the insulation materials may result in
defective insulation and even electric leakage. If the relative humidity is low, the insulation spacer may result in dry
shrinkage, which will make screws looser and easily generate static electricity in the dry environment, thus damaging the
interior circuits on the device. Excessively high temperature will accelerate the aging of insulation materials and
compromise the reliability and even service life of the device. The temperature/humidity requirements are shown below
(detailed difference between products is described in the chapter of "Product Overview"):
Table 2-1 Temperature and Humidity Requirements of Ruijie EG Series Breakout Gateways
Temperature Relative Humidity
Long-term working
condition
Short-term working
condition
Long-term working
condition
Short-term working
condition
15ºC to 30ºC 0ºC to 45ºC 40% to 65% 10% to 90%
The temperature/humidity of working atmosphere indicates the value measured at 1.5 m above the floor and
0.4 m ahead of the equipment frame when there is no protection plate on the front and rear side of the
equipment frame.
Short-term working condition refers to the continuous operation no exceeding 48 hours or accumulative
operations no exceeding 15 days in a year.
Extremely harsh working environment generally refers to the ambient temperature and humidity which may
be encountered when the equipment room air-conditioning system fails but will recover in less than 5 hours
every time.
Cleanliness Requirements
The dust is also a major threat to the safe operation of device. The dust accumulated on the device may cause
electrostatic adsorption and result in poor contact. It will not only compromise the service life of device but also cause
communication failure. When the indoor relative humidity is low, such electrostatic adsorption will incur more easily.
Table 2-2 The Equipment Room Dust Content and Particle Size Requirements of Ruijie EG Series Breakout
Gateways
Maximum Diameter (μm) 0.5 1 3 5
Maximum Density (Particles/m3) 1.4 x 1077 x 1052.4 x 1051.3 x 105
Apart from the dust, the device is also sensitive to the hydrochloric acid sulfide contained in the air. These noxious gases
will accelerate metal wastage and the aging of certain parts. The upper limits of noxious gases (Sulfur dioxide, Sulfured
hydrogen, Nitrogen dioxide, Ammonia and Chlorine) in the equipment room are shown in Table 2-3:
Table 2-3 Upper Limits of Noxious Gases of Ruijie EG Series Breakout Gateways