Planet WSG-500 User manual

300Mbps Hotspot Wireless Subscriber Gateway
WSG-500
Quick Installation Guide

Table of Contents
1. Requirements .............................................................................................. 3
2. Package Contents ........................................................................................ 4
3. WSG-500 .................................................................................................... 5
4. Installation .................................................................................................. 7
5. Hardware Connection and Installation............................................................ 8
6. Conguration of Your WSG-500....................................................................10

3
1. Requirements
Cable modem or DSL/ADSL modem.l
Network cables.l
Use standard 10/100Base-TX network (UTP) cables with RJ45 connectors.l
Subscriber PC installed with Wireless adapter that complied with 802.11b,l
802.11g or 802.11n.
Workstations of subscribers running Windows 2000/XP, MAC OS9 or later.l
Linux, UNIX or other platform compatible with TCP/IP protocols.l
<Optional> Account generator (Model No.: WSG-ACG5).l
Hint
Mac platform should be OS9 or later in order to have DHCP client
support.

4
2. Package Contents
1 x WSG-500 unitl
1 x Power Adaptorl
1 x User’s Manual CDl
1 x Quick Installation Guidel
1 x RJ-45 Cablel
1 x RS-232l
2 x Antennal
1 x Ground Wirel
1 x Screw Packagel

5
3. WSG-500
Overview Top Panel
The top panel of PLANET WSG-500 is shown below.
Front Panel
The Front panel of PLANET WSG-500 is shown below.
LED Denition
LED Color Status LED Description
PWR
Blue Off
On
The device is turned off
The device is turned on
WAN Blue
Off
On
Flashing
The WAN is not connected.
The WAN has a successful (10/100Mbps)
Ethernet connection.
The WAN is sending or receiving packet.
LAN 1
LAN 2 Blue
Off
On
Flashing
The LAN is not connected.
The LAN has a successful (10/100Mbps)
Ethernet connection.
The LAN is sending or receiving packet.
WLAN Blue
Off
On
Flashing
The wireless is not ready.
The wireless is ready.
The wireless is sending or receiving packet.

6
INTERNET
Blue Off
On
The WAN is not connected to the internet.
The WAN is connected to the internet.
WES*
Blue
For indicating WES status during WES setup:
Master Slave
WES Start LED ashing
slowly LED ashing quickly
WES Negotiate LED ashing
slowly LED ashing quickly
WES Fail
(Negotiate
Timeout)
LED OFF LED OFF
WES Success LED ON for
over 5 seconds
LED ON for over 5
seconds (after Master
displays WES Success)
USB*
Blue N/A For future usage only.
Remark: WES is a future supported feature.
Port Indication
Power Reset WAN LAN 2 LAN 1 Console WES USB
Printed on
Housing 12V/1A Reset WAN (PoE) LAN2 LAN1 Console WES USB
Interface Power Button RJ-45 RJ-45 RJ-45 RS-232 Button USB
Power The power adaptor plugs here.
Reset Used for restarting the system.
WAN
(PoE)
One RJ-45 port is used for connecting xDSL or Cable Mode to the
Internet/Intranet.
LAN2 Used for Connecting to the public LAN. It can be chosen to require
authentication to access network resource and the Internet.
LAN1 Used for Connecting to the private LAN. Authentication is not
required to access the network resource from here.
Console Used for conguring the system via Hyper Terminal.
WES* Used for starting WES (WDS Easy Setup) process. For future usage.
USB* For future usage only.

7
4. Installation
The followings are instructions for setting up PLANET WSG-500. Refer to the
illustration and follow the simple steps below to quickly install your Wireless
Subscriber Gateway.
Connecting the Antennas
PLANET WSG-500 provides two antenna connectors on the rear of the unit for
wireless subscribers.
Installation Requirement
Before installing PLANET WSG-500, make sure your network meets the following
requirements.
System Requirements
PLANET WSG-500 requires one of the following types of software:
Windows 95/98/NT/2000/XPl
Any TCP/IP-enabled systems like Mac OS and UNIX (TCP/IP protocol installed)l
Standard phone line for xDSL modem or coaxial cable for Cable modem for l
Internet access
Web Browser Softwarel
(Microsoft I.E 4.0 or later version or Netscape Navigator 5.0 or later version)l
One computer with an installed 10Mbps, 100Mbps or 10/100Mbps Ethernet cardl
UTP network Cable with a RJ-45 connector (Package contents)l
Hint
Mac platform should be OS9 or later in order to have DHCP client
support.

8
5. Hardware Connection and Installation
Physical Installation
Internet
Public Zone
Private Zone
WSG-500
Mobile Guests
Administration
Laptop
PoE Switch
ADSL/Cable
Modem
Smart Phone
Laptop
Administrator
Clerk
Smart Pad
100Base-TX UTP
PoE
100Base-TX UTP with PoE
Telephone wire
2.4GHz 802.11n
N
N
N
N N
N
N
PoE
Ticket
Generator Printer
Physical connection of WSG-500

9
1. Ensure the WSG-500 and the Cable/DSL modem are powered OFF before
commencing. Leave your Cable/DSL modem connected to its wall socket (phone
line or cable input).
2. Use Ethernet cables to connect to the LAN2 port on the front panel. Connect
the other end of the Ethernet cable to an AP or Switch. (Note: Authentication is
required for the clients to access the network via LAN2 port. The LAN port with
authentication function is referred to as Public LAN).
3. Use Ethernet cables to connect to the LAN1 port on the front panel. Connect the
other end of the Ethernet cable to a PC. (Note: Authentication is NOT required
for the clients to access the network via LAN1 port. The LAN port with authenti-
cation function is referred to as Private LAN).
4. Connect your Cable/DSL Modem to the WAN port on the front panel. Use the
cable supplied with your Cable/DSL modem. If no cable was supplied with your
modem, use a standard network cable. Please make sure the connection is
established (LED is on).
5. Connect the Power Adapter. Use only the unit provided.
6. Power ON. The PWR LED should stay on (If your network is connected, the
WAN/WLAN/LAN LED will be on, too).
7. Power on the PC that connected to the WSG-500.
Hint
1. Please consult your ISP personnel to obtain proper Internet
connection related information, and input carefully.
2. If Internet connection cannot be established, please check the
WAN LED display, inserted parameters or contact the ISP service
staff for support information.
3. Account Generator WSG-ACG5 is an optional device.
4. It is recommended that you leave IP settings on subscriber PC
as automatically assigned. By machine default configurations,
WSG-500 will act as a DHCP server, and it will assign PC the
necessary IP settings.

10
6. Conguration of Your WSG-500
Getting Started
The WSG-500 supports web-based conguration. After completing the hardware
installation, WSG-500 can be congured through a PC by using web browser.
To access the web management interface, connect the PC and WSG-500 in advance
via the Private Port of WSG-500. Then, launch the web browser and enter the IP
address of the gateway for that port in the address eld then press Enter. Default
IP address of the default gateway of the Private Port is https://192.168.1.254
(Note: https is used for a secured connection).
The administrator login page will appear. Enter default username “admin” & default
password “admin” in the User Name and Password elds. Click Enter to login.
After logging into WSG-500 successfully, a web management interface with a
welcome message will appear.
Click Setup Wizard to help you complete the conguration.
Setup Wizard
Step 1: General
Enter a new password for the admin account and retype it in the verify pass-
l
word eld (Twenty characters maximum and no spaces allowed).