RUPTELA fm-eco4 light 3g User manual

0
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
FM-Eco4 light 3G/light+ 3G
FM-Eco4 light/light+
User Manual
2019/03

1
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
Table of contents
1 Preface................................................................................................................................... 2
1.1 Use of this document ........................................................................................................ 2
1.2 Document change log ....................................................................................................... 2
2 Introduction............................................................................................................................ 3
2.1 Purpose ........................................................................................................................... 3
2.2 Acronyms......................................................................................................................... 3
2.3 Legal Information ............................................................................................................. 3
2.4 Document application ....................................................................................................... 3
2.5 Safety.............................................................................................................................. 3
2.6 References....................................................................................................................... 4
3 Device description ................................................................................................................... 5
3.1 About .............................................................................................................................. 5
3.2 Package contents ............................................................................................................. 5
3.3 Physical characteristics...................................................................................................... 6
3.4 Technical characteristics.................................................................................................... 6
3.5 IO pin out ........................................................................................................................ 6
3.6 Peripheral accessories ....................................................................................................... 6
3.7 Certification...................................................................................................................... 7
3.8 LED Status ....................................................................................................................... 7
4 Device preparation .................................................................................................................. 8
4.1 Opening/Closing the device ............................................................................................... 8
4.2 Connecting the USB cable.................................................................................................. 9
4.3 Inserting a SIM card ......................................................................................................... 9
4.4 IO cable........................................................................................................................... 9
5 Device configuration.............................................................................................................. 10
5.1 Driver installation............................................................................................................ 10
5.2 Sample configuration ...................................................................................................... 12
5.3 Advanced configuration................................................................................................... 14
5.3.1 Global settings ......................................................................................................... 16
5.3.2 Profile settings......................................................................................................... 21
5.3.3 IO settings .............................................................................................................. 26
5.4 Integration protocol ........................................................................................................ 31
6 Installation recommendations................................................................................................. 32
6.1 Device installation........................................................................................................... 32
6.2 Device mounting position ................................................................................................ 32

2
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
1Preface
1.1 Use of this document
This document provides required information for proper device handling, preparation, configuration and
installation to a vehicle. This document has a linear structure –from the device package box reception
to the recommendations on how to install the device to the vehicle. However, it is not overfilled with
unnecessary information. You will find only basic descriptions about various functions and actions needed
to start using the device with the reference to extensive descriptions of the contents.
The following markings are used to highlight important information:
Notes contain important information that you need to pay attention to.
Note
Notes like this contain important information!
Actions and various elements of the software required for configuration of the device are marked
in bold.
All actions are described in sequence in the following five sections: Introduction, Device
description, Device preparation, Device configuration and Installation recommendations.
1.2 Document change log
Date
Version
Change details
2016-07-21
1.0
Initial draft
2017-02-06
1.1
“Constant TCP link” functionality description in “Profile settings” chapter.
2017-03-09
1.2
Changed DIFF file description in “Advanced Configuration” chapter.
2017-03-13
1.3
Added temperature range for battery.
2017-04-12
1.4
1-Wire interface added.
2017-05-08
1.5
“GSM tracking” feature description and option to enable/disable SIM status
feature in “Global settings” chapter. Configurable sleep mode description in
“Profile settings” chapter.
2017-05-24
1.6
Removed “Absolute maximum ratings” in common specifications.
2017-06-08
1.7
Automatic IO enable function in IO setting chapter.
2017-08-30
1.8
Debounce description added in "IO settings" section.
2017-10-18
1.9
Added “Configuration information” description in the “Sample configuration
section.
2017-12-22
1.10
Added description of “Link settings –Heartbeat” in the “Profile settings”
section. Added note regarding greyed out fields in “Global settings”.
2018-05-11
1.11
Added description of automatic firmware update from configurator.
2018-06-06
1.12
Added description of invertible digital inputs DIN3 and DIN4 for FM-Eco4
light 3G and FM-Eco4 light+ 3G. Technical characteristics moved to
datasheets.
2018-08-24
1.13
Added description of “Periodical redirect” in “Global settings”.
2018-10-23
1.14
Added description of sending only header information in records in “Profile
settings”. Updated description of “Send identification string” in “Global
settings”.
2018-11-19
1.15
Updated operating system requirements in “Sample configuration”. Added
description of DOUT inversion in “IO settings”.
2018-12-06
1.16
Updated list of the peripheral devices in “Peripheral accessories”.
2019-03-08
1.17
LED status diagrams replaced by a table in “LED status”.
Updated description of “Operator list”.
Updated description of “Configurable navigation filtering” in “Profile
settings”.

3
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
2Introduction
2.1 Purpose
The purpose of this document is to provide physical and technical data of the device, to explain device’s
behavior and how various conditions are indicated. Also, device preparation for operation and its
configuration instructions are included.
2.2 Acronyms
AC / DC –Alternating Current/Direct Current;
ACK - A signal to acknowledge the receipt of data;
GLONASS –Global Navigation Satellite System;
GNSS –Global Navigation Satellite System;
GPRS –General Packet Radio Service;
GPS –Global Positioning System;
GSM –Global System for Mobile Communications;
IO –Inputs / Outputs;
LED –Light Emitting Diode;
PC –Personal Computer;
PCB –Printed Circuit Board;
SELV –stands for Safety Extra Low Voltage. A SELV circuit is a secondary circuit which is so designed
and protected that under normal and single fault conditions, its voltages do not exceed a safe value.
SMS –Short Message Service;
UMTS –Universal Mobile Telecommunications System;
2.3 Legal Information
Copyright © 2019 Ruptela. All rights reserved. Reproduction, transfer, distribution or storage of parts or
all of the contents in this document in any form without the prior written permission of Ruptela is
prohibited. Other products and company names mentioned in this document are trademarks or trade
names of their respective owners.
2.4 Document application
Given parameter values and various characteristics within this document apply only to the most recent
device hardware version.
2.5 Safety
All the associated (additional) equipment such as PC’s, batteries, sensors etc., shall meet the
requirements of standard EN60950-1.
Do not disassemble the terminal. If the enclosure of the terminal is damaged, or the insulation
of wires is damaged, first of all disconnect power supply cables from the power supply source.
All of the wireless data transferring equipment produces interference that may affect other
devices, which are placed nearby.
The terminal can be installed or dismounted only by qualified personnel!
The terminal must be firmly fastened in the predefined location. Predefined location is described
in the mounting instructions.
The programming must be performed using a 2nd safety class PCs (with an autonomic power
supply).

4
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
Make sure that the terminal is installed in a place, where it will not be subjected to harsh
environmental conditions for extended time periods.
Any installation and/or handling during a lightning storm is prohibited.
Caution! If an incorrect type of battery is used for replacement, there is a high explosion risk.
Dispose used batteries according to the environmental requirements.
For configuration use cables that were purchased from Ruptela. Ruptela is not responsible for
any harm caused, while using wrong cables for the PC ↔ Terminal connection.
Attention! Do not connect the wires marked red (power supply) and black (chassis) to the wrong
battery poles. Device has a reverse polarity protection, however if connected incorrectly, the
device will not work.
To disconnect the device from the power supply, you need to disconnect 12 PIN plug from the
device or disconnect the wires from the vehicle‘s power supply.
This crossed-out wheelie bin symbol means that waste equipment should not be disposed of
with your other household waste. The product must be taken to separate collection points at
the product`s end-of life.
This chapter contains procedures to help you safely operate the FM terminal. By following these
requirements and recommendations, you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the device! The terminal is supplied from
a car battery with these ratings: 12/24 V DC. The allowed voltage range from the battery is from 10
volts to 32 volts DC. Max. current 150 mA @ 12 V DC ( Supplied from SELV power supply source ).
To avoid mechanical damage, it is advised to transport the FM terminal in an impact-proof package.
Before connecting wires of the 12 PIN cable to the vehicle, it is recommended to ensure that the cross-
sectional area of wires mounting is at least 0.75 mm2. To correctly dismount the terminal from the
vehicle, first of all disconnect power supply wires. Only then other plugs or interfaces can be
disconnected.
The terminal is intended to be installed in a restricted access location, which is not accessible for the
operator.
2.6 References
This document is designed to work in a conjunction with other documents. Documentation is kept light,
unnecessary information is omitted. Additional and extensive explanations can be found in the
documentation referenced below:
FM-Eco4 light/light 3G datasheets –contain technical data of the FM-Eco4 light/light+ and FM-
Eco4 light 3G/light+ 3G devices.
Peripheral accessories –Instructions on how to use peripheral accessories together with the FM-
Eco4 light /light 3G device.
Website –Our documentation website that contains the latest firmware, configurator and sample
configuration files.
Microsoft Framework –This additional software is required in order to run our configurator.
VCOM drivers –Drivers are required in order to connect the device to a PC.
All links are also provided in corresponding sections, where additional information might be needed.
Note
Ruptela documentation website address: doc.ruptela.lt

5
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
3Device description
3.1 About
Ruptela‘s FM-Eco4 light / FM-Eco4 light 3G device is a 4th generation low cost, low power consumption
basic tracking device. It acquires its position by a GPS/GLONASS signal and transfers data to a server
via cellular GSM/GPRS/3G network. 3G network support was not previously available for FM4 devices.
This new feature in FM-Eco4 light 3G is the main advantage over the FM-Eco4 light devices.
Both device versions FM-Eco4 light and FM-Eco4 light 3G have various improvements over the older 3rd
generation FM-Eco3 devices:
Lower power consumption
1-Wire interface
Internal GPS/GLONASS antenna
FM-Eco4 light FM-Eco4 light 3G
Both devices can have an internal power supply source. Device versions with batteries are labeled
FM-Eco4 light+ and FM-Eco4 light+ 3G.
3.2 Package contents
FM-Eco4 light / FM-Eco4 light 3G device is supplied in a cardboard.
Package contents:
FM-Eco4 light / FM-Eco4 light 3G device or its variant with
battery
12 PINs cable
USB 2.0 cable: USB A - male to mini USB B (as an optional
accessory)
Note
Providing a SIM card is optional, according to your payment plan. The SIM card is necessary for
connection to the GSM network. The SIM card can be obtained from your local GSM service provider.
The SIM card can work with the terminal only when all SIM card security codes are disabled.

6
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
3.3 Physical characteristics
Properties
Enclosure dimensions
64.5L x 61W x 22H mm
Indication
3 LEDs: GNSS status, GSM status, 1-Wire status
Housing
Plastic
Configuration interface
USB
Connectors
12 Pin, insulated
3.4 Technical characteristics
Technical characteristics can be found in FM-Eco4 light and FM-Eco4 light 3G datasheets.
3.5 IO pin out
Pin
Wire color
Description
10-32 V
Red
Power supply 12/24 V (range: 10-32 V)
Chassis
Black
Ground connection
DIN1
Pink
Digital input, threshold 4 V
DIN2
Blue
Digital input, threshold 4 V
DIN3
White
Digital input, threshold 4 V (invertible)
DIN4
Yellow
Digital input, threshold 4 V (invertible)
AIN1
Grey
Analogue input (range: 0-30 V)
AIN2
Green
Analogue input (range: 0-30 V)
DOUT1
Purple
Digital output open collector up to 32 V, 1 A
DOUT2
Orange
Digital output open collector up to 32 V, 1 A
1-Wire POWER
White with red stripe
1-Wire power output: 80 mA @ 4.1 V
1-Wire DATA
Green with yellow stripe
1-Wire data transfer
3.6 Peripheral accessories
There are several peripheral accessories that can be connected to the FM-Eco4 light/ FM-Eco4 light 3G
device. With these peripherals you can get even more features and extended functionalities. All available
peripherals can be purchased from Ruptela. Please contact your manager for more details.
Note
1-Wire power maximum power output is 80 mA @ 4.1 V
Available on 1-Wire:
4 × Temperature sensors DS18B20/DS18S20
1 × iButton DS1990
1 × 1-Wire RFID
Available on DOUTs:
1 × Buzzer/LED
1 × ECO Driving panel (power supply from 1-Wire)
1 × Ignition lock
Available on DINs:
1 × Panic button
1 × Door sensor

7
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
Available on AINs:
2 × Analog fuel sensors
You can find peripheral accessories installation instructions and documentation on our website.
3.7 Certification
FM-Eco4 light and FM-Eco4 light 3G devices have passed quality tests and comply with the following
certifications:
E-Mark
CE ready
3.8 LED Status
The device has three LEDs with different blinking patterns that show the state of the device's
communication.
LED
Pattern
Description
GNSS
Once every second
Accurate signal
Once every 0.4 seconds
No signal
GSM
Once every 4 seconds
Accurate signal
Once every 0.2 seconds
No signal
Always on
Link with the server is open
1-Wire
Always off
No devices connected
Once every 5 seconds
One device connected
Twice every 5 seconds
Two devices connected
Three times every 5 seconds
Three devices connected
All
Once every 5 seconds
Sleep/deep sleep mode

8
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
4Device preparation
In order for the device to work you have to
configure it and insert a SIM card. To do so, you
have to open the device enclosure and perform
certain actions described below.
4.1 Opening/Closing the device
Use a screwdriver or a similar tool to open up the
plastic housing of the device. It is recommended to
use a flat-head type screwdriver ( see figure on the
right ). Inappropriate tools might cause permanent
damage to the device.
To correctly assemble the device you have to know
the exact positions of all the plastic pins used to hold
the PCB in place ( see figure on the right ). These
positions are listed in the table below:
Proper assembly sequence:
1. Make sure that the PCB is facing up. Only then it can be mounted in its plastic housing.
2. The PCB goes under the intermediary plastic pin - 1.
3. Then it is mounted on the stabilizer –2.
4. The PCB must be correctly placed on the PCB support pin - 3.
When the assembly sequence described above is completed, push the other side of the PCB down into a
stable position.
The plastic lid of the device can be mounted only
when all of the PCB pins are holding the PCB in a
stable position ( see figure above ).
To correctly seal the plastic housing of the device,
start by placing the plastic lid at either side of the
device ( see figure on the right ). Then push the
remaining side down until the housing is fully
closed.
Note
It is recommended to keep the number of opening procedures to the minimum.
No
Name
1
The intermediary PCB pin
2
The PCB stabilizer pin
3
The PCB support pin

9
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
4.2 Connecting the USB cable
Connect a mini USB cable to the device ( see figure on the
right ). The cable can be connected only in one way, be
careful not to damage the plug. Connect the other end to
your PC or a laptop.
Before starting the configuration procedure of the device,
make sure that it is connected to the external power
supply.
4.3 Inserting a SIM card
If you received a device without a SIM card, place your
own SIM card into the device as shown in the picture
below. The microchip must be facing down.
4.4 IO cable
Connect the IO cables plug to the Micro - Fit slot on the
device ( see figure on the right ). The cable can be
connected only in one way.

10
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
5Device configuration
5.1 Driver installation
Virtual COM port driver installation is mandatory, only then your PC will recognize the FM-Eco4 light device
that was connected to the USB port. You can download the latest driver from our documentation website
server (VCOM drivers).
Choose the correct archive file with drivers for your OS version and download it to your PC.
Installation procedure:
Uninstall any previous Virtual COM port driver versions:
Start -> Settings -> Control Panel -> Add or remove programs (Windows 7);
Start -> Settings -> Apps -> Apps & features (Windows 10);
Extract archive file “Win7.zip” or “Win8.zip” to a desired location on your PC.
If you are running a 32-bits OS version, launch the “dpinst_x86.exe” [1.]
If you are running a 64-bits OS version, launch the “dpinst_amd64.exe” [2.]
Windows 7 Users might get a Security Warning message. Click “Yes” [3.].

11
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
In the next window select “Next” [4.].
Wait for the setup to complete the installation and click “Finish” [5.].
The driver is now installed and ready to use.

12
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
5.2 Sample configuration
Go to our documentation website server and download sample configuration and the latest configurator.
Also you will need the latest version of Microsoft Framework.
Operating system requirements:
MS Windows 7/8/10
Start VCP.exe from configurator folder.
1. Select Eco4.
2. Click File → Open CFG.
3. In the dialog window, browse the sample configuration file that you have downloaded from the
documentation website.
4. Click Open.

13
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
Configuration information
Starting from configurator version 00.03.04.XX, the configurator will display additional information
regarding the loaded configuration. The following information will be displayed at the top of the
configurator once a configuration is loaded (if no configuration is loaded, the fields will be empty):
1. Configuration source –can be from “Configurator” or from “Device”.
Configurator –means that the configuration is loaded from the PC;
Device [Device_IMEI] –means that the configuration was received from the FM device;
2. FM device FW version –this will be displayed only if the configuration was received from the
device;
3. FM4 configurator version –show the configurator version on which the currently loaded
configuration was made;
4. Target device –display the FM device model for which this configuration was created or from which
device it was downloaded;
5. CFG Tag –is simply additional information that the user can save with the configuration file.
Maximum length is 32 symbols, only printable ASCII characters are allowed;
6. Last edited –display the date and time when the configuration was last edited. If the edit was
from a PC, the time will be the same as the PCs local time. If the configuration was received from
the device, and the device currently has no time from any source, the date and time will be shown
as the beginning of this century (2000/01/01 00:00:00);
7. If any changes were made to the currently loaded configuration, a small “*” symbol will appear
next to the name of the configuration.
Configuration additional steps
Sample parameters will be loaded. However you will need to enter other parameters on your own.
1. Enter IP (in the 255.255.255.255 format) or a Domain Name (not exceeding 40 characters) and
PORT to which the device should send data.
2. Enter APN settings: APN name, User login and Password (if login and password needed). If you
choose to enable Lock FM device to the SIM card check-box you will be required to enter SIM
card’s PIN code every time you try to connect to the device via USB cable. As long as it is checked
you will not be able to use different SIM cards with this device.
3. Select a COM port you connected the device to and click Connect. At this point the configuration
is ready to be send to the device, so the device must be connected to the computer.
4. Click Send CFG button. The configuration will be uploaded to the device.
Note
APN name, login and password should be provided by your mobile network operator.

14
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
Now the device is configured to send data to the specific server. Sample IO parameters are enabled
(loaded with configuration file). You can log in to your tracking platform to see whether the device is
sending data.
5.3 Advanced configuration
The configuration tool is quite similar to the one used for 3rd generation devices. Overview of the
configuration is described in sections.
The File menu gives you access to control
configuration files. Choose New/Save/Open CFG to
perform the corresponding action. CFG means full
configuration file.
New CFG wizard –It helps users to go through all
basic configuration steps.
Generate SMS –This tool allows the user to
generate a SMS command to configure the FM device remotely. Working principle and general SMS
command functionality is described in the “Device configuration via SMS” document at doc.ruptela.lt
The Tools menu contains:
Language selection options: English or Russian are available.
Diagnostics tool.
Save/Open DIFF allows you to create a DIFF file. DIFF files are used to change only one or few certain
parameters without a need to upload the full configuration to the device. It is useful, when updating over-
the-air.
Attention
A DIFF file will save all made changes to a configuration. For example changing a number in the IP filed,
or marking a checkbox, but, if a change was made, and afterwards reverted to the previous state
(checkbox checked, and unchecked afterwards), this will not be marked as a "change made". DIFF will
only record changes made to the initial configuration (a loaded pre-set configuration is considered an

15
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
initial configuration). Particular attention must be taken, when creating a DIFF file, to avoid accidental
changes to the configuration.
The control panel on the left hand side allows you to select and control the device.
Select the COM port that the device is connected to and click “Connect”. At this
point the FM4 configurator checks the compatibility between itself and firmware in
the device. Every firmware version is released together with a recommended FM4
configurator. More information about different firmwares and recommended
configurators for them can be found in firmware changelogs. After the compatibility
check, three outcomes are possible:
1. The firmware and configurator versions are compatible. Go ahead and continue
configuring the FM device.
2. The configurator is too old for the current firmware version. An error message
will appear. The “Send CFG” and “Get CFG” buttons will be disabled. You will
need to download a new version of the configurator, recommended for the
firmware version.
3. The firmware is too old for the current configurator version. An error message
will appear. The configurator will suggest to update the firmware automatically. To update the
firmware, click “Yes”. The firmware will be updated to the version supported by the configurator.
This can be done without an internet connection. Click “No” to close the message without updating
the firmware. If the firmware is not updated, the “Send CFG” and “Get CFG” buttons will be
disabled. We highly recommend using the latest firmware and configurator.
The “Send CFG” and “Get CFG” buttons are used to send and receive the configuration file to/from the
device.
“Send FW” is used to send new firmware to your device manually.
In the drop-down list below you can select the model of the device. If you connected one to your PC, it
will be displayed. Now Eco4 should be displayed.

16
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
5.3.1 Global settings
The first part of the configuration tool is “Global” settings. Global include connection settings and other
settings independent from the profile settings –global settings are the same for all profiles.
Connection settings here you should enter server IP and port that the device should connect to. The
IP can be entered in the numeric format: 255.255.255.255. You can also use a Domain name (not
exceeding 40 characters). IP2 is a backup IP address, which is used when the device is unable to connect
to the first server.
Note
Please have in mind that ports for TCP and UDP transfer protocols usually are different –please select
the correct transfer protocol and enter the correct port.
Two servers –checkbox changes the logic described above. It enables a two servers mode –the
same data is repeatedly transmitted to another server with IP2, unless we get a timeout. IP1 is
dedicated IP for server, from which we get the ACK’s for our record packets sent. After we get the
ACK from this IP, record data is considered as successfully transmitted to the server and it is
removed from the memory.
In this mode data is sent to IP2 only when connection to the IP1 is established. Packet, which is
sent to the IP1 server is also sent to the IP2 server.
Only records are going to be send to the IP2. Data packets such as Transparent Channel,
Tachograph, SD card, Garmin will not be send to the IP2.
Unable to send data:
When unable to establish connection to IP1, device does not connect to the IP2 as well. When
connected to IP1 and doing data transmission, but IP2 is unreachable –after receiving ACK from
IP1 server, data is removed from memory, which can cause information loss in IP2 server.
Note
Two server mode doubles the amount of data that is being sent. Before using this functionality consider
the cost which arises from the higher data traffic.

17
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
Periodical redirect –clicking on this button will open the “Periodical redirect” window. This
functionality is used to periodically redirect the FM device to a specified server to initiate automatic
configuration or firmware updates when using 3rd party tracking software. The following settings
can be changed:
IP –the IP address of the server. The
default value is 92.62.134.34;
Port –the port of the server. Note:
the redirection is done using the TCP
protocol. The default value is 9015.
Period –how often the device should
connect to the server. The period is
measured in hours. The default value
is 0 hours. The maximum value is 168
hours (1 week). If it is set to 0 hours,
the functionality is disabled.
Once the period timer passes, the device checks the following conditions:
If there are unsent records in device memory;
If the GSM level is lower than 9;
If the power supply voltage status is 0 (refer to the version SMS command);
If the device is in a critical process.
If at least one condition is true, the device waits until no conditions are true. If none of the
conditions are true, the device connects to the previously configured server. The device then
initiates updates and closes the connection. After the connection to the server is closed, the period
timer is reset to zero.
Protocol section allows you to choose from two protocols. UDP protocol is less reliable than the TCP,
but also uses less traffic. TCP uses more internet traffic, but it is more reliable. Choose one according to
your needs.
Note
If the IP, port or APN fields are greyed out when the device is connected to
the configurator, their values cannot be changed.
APN settings are needed for internet connection. These settings must be
provided by your mobile network provider. Without APN settings the device will
not send any data.
If you choose to enable the Lock FM device to the SIM card check-box you will be required
to the enter SIM card’s PIN code every time you try to connect to the device via USB cable. As
long as it is checked you will not be able to use a different SIM card
with this device.
Note
If the “SIM status” checkbox is not enabled, the “Enter PIN” window will not
appear when connecting to a FM device. This means you will not be able to
access your device.
If the wrong PIN is typed in more than three times, the SIM card will be locked.
It can be returned to its original unlocked state by entering a PUK, provided by the service operator after
verification. If the wrong PUK is entered ten times in a row, the device will become permanently blocked
and unrecoverable, requiring a new SIM card. Once you enter the PUK code, you must set a new PIN.

18
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
SIM status section at the bottom of the configuration tool displays SIM card related information. By default
feature is disabled. Tick the checkbox to enable it.
Total of seven different statuses are available:
1. Ready –PIN code is known or PIN code check is disabled. GSM/GPRS (/UMTS) modem can operate
normally.
2. Error –Represents a wide range of possible problems. Common reason would be old FW version,
which does not support SIM commands.
3. Unknown –Communication between device and GSM/GPRS (/UMTS) modem failed, SIM status is
unknown.
4. PIN Request –SIM card requests a PIN code, FM device cannot provide it (code provided by the
device is incorrect).
5. PUK Request –SIM card requests a PUK code.
6. Locked –This FM device is attached to a different SIM card.
7. Not inserted –SIM card is not inserted.
Configuration password allows to lock the configuration –without the password no one can change
the device configuration via cable. However, over-the-air update ignores the configuration password.
Driver registration is used to authorize the start of the vehicle, identify a driver and account working
hours. The full functionality description can be found on our documentation website, Driver registration.
Send data without GPS fix - device cold-start often causes issues, because it is not sending data,
therefore the user is unable to see parameter values until GPS fix is obtained. This functionality allows
data sending even when there is no GPS fix. A full functionality description can be found in “Send data
without GPS fix” document on our documentation website.
When the device loses GPS fix, there is no way to determine its location. GSM tracking feature can now
be used to obtain an approximate location in densely urbanized areas, where GNSS signal is not available.
Full functionality description can be found in “Send data without GPS fix” document on our documentation
website.
GNSS allows to select positioning network –GPS, GLONASS or GPS+GLONASS. GPS+GLONASS by default
( recommended not to change this ).
Geofencing allow to use internal geozones, configured directly into device. Full description can be found
on our documentation website, Internal geozones.

19
Main Support no.: [phone]
Polish Support no.: [phone]
Ukrainian Support no.: [phone]
[e-mail] | www.ruptela.com
Towing detection –with Towing detection driver can be informed, that his car is being towed.
Information about such event is sent to the server, therefore driver might still have time to come back to
his vehicle before it is taken away. A full functionality description can be found on our documentation
website.
Impact detection –when this feature is active, FM device monitors its acceleration in all directions and
generates records, when acceleration exceeds configured limits. Clients can use this feature to get
notifications to the server about irresponsible drivers, who hit sidewalks or other obstacles. A full
functionality description can be found on our documentation website.
Authorized numbers
Set a Password to restrict access to the SMS commands
feature.
SMS Alert Number –when specific I/O parameter is
triggered, the FM device will send an alert message to this
number.
In the Valid Numbers table enter specific numbers that will
be able to send commands to the device.
Enable configuration over SMS checkbox controls
configuration over the SMS feature. A full functionality
description can be found on our documentation website.
ECO Driving options are used to choose sensitivity for the ECO Drive functionality. It helps to rate drivers
according to their safety or according to driver's behavior. Full functionality description can be found on
our documentation website, ECO Drive.