RUPTELA FM-Tco4 HCV User manual

www.ruptela.com [e-mail] | [phone]
FM-Tco4/FM-Pro4
Quick Start Guide
Q
FM-Tco4 HCV
FM-Tco4 LCV
FM-Pro4
Make sure that you have:
•A computer with Windows 7/8/10
•An internet connection (or a predownloaded Device Center)
•A USB A to USB mini (Type B) cable
•Tools for installation and wire connection: a screwdriver, a panel removing tool, a wrench, a crimp terminal,
zip-ties (or double-sided tape)
Device overview
Indication LEDs
USB mini (Type B) port
Audio jack
GNSS antenna port
14 Pin port
12 Pin port
12 Pin cable pinout
Pin
Wire color
Description
+BAT
Red
Power supply
12/24V
GND
Black
Ground connection
DIN1
Pink
Digital input 1
DIN2
Blue
Digital input 2
DIN3
White
Digital input 3
DIN4
Yellow
Digital input 4
AIN1
Grey
Analog input 1
AIN2
Green
Analog input 2
DOUT1
Purple
Digital output 1
DOUT2
Orange
Digital output 2
CAN2 L
Blue/Red
CAN Low
CAN2 H
White/Red
CAN High
14 Pin cable pinout
Pin
Wire color
Description
PortB-232 RX
Yellow
RS232 RX
GND
Black
Ground connection
PortB-232 TX
Orange
RS232 TX
1W +5V
Red
1-Wire power
PortA-232 RX
Purple
RS232 RX
1W Data
Green/Yellow
1-Wire data
PortA-232 TX
Pink
RS232 TX
CAN1 H
White
CAN High
L-Line
Green
L-Line
CAN1 L
Blue
CAN Low
K-Line
Brown
K-Line
GND
Black
Ground connection
PortC-485A
White/Red
RS485 line A
PortC-485B
Yellow/Brown
RS485 line B

www.ruptela.com [email protected] | [phone]
Indication LED patterns
LED
Pattern
Description
GNSS
Once every second
Accurate signal
Once every 0.4 seconds
No signal
GSM
Once every 4 seconds
Accurate signal
Once every 0.2 seconds
No signal
Always on
Link with the server is open
Peripheral
Always off
No devices connected
Once every 5 seconds
One device connected
Twice every 5 seconds
Two devices connected
Three times every 5 seconds
Three devices connected
All
Once every 5 seconds
Sleep/deep sleep mode
Configuration
Insert your SIM card into the device.
Download and launch the Device Center.
Install device drivers if prompted.
Click Configure device in the main menu.
Connect the device to your computer using a USB
cable.
Click Connect device.
Select your device.
Insert SIM

www.ruptela.com [email protected] | [phone]
Open the Connection settings.
Configure Fleet Management System Main Server settings (TrustTrack server settings are entered by
default).
Configure GSM provider APN settings.
Click Save to device to upload the config to the device.
Installation
For faster and easier installation, it is highly recommended to use installation harnesses.
Install the device, make sure the label is facing towards the sky and is not covered by metal.
Follow the recommendations:
•It is allowed to tilt up to 45 degrees in any axis, but the top surface in all cases must be facing up
•Install behind the dashboard
•Install as close to the windshield as possible
•Avoid installing near metal surfaces
Fasten the device in the vehicle using zip-ties or double-sided tape.
Make sure it is secured tightly.
Install the GNSS antenna facing towards the sky.
Connect the device according to the wiring diagram (on Page 4).
Turn on the ignition.
Check that the required data is received before finishing the installation.

www.ruptela.com [email protected] | [phone]
Wiring diagram
•Power input 12/24 V DC
•Recommended protection fuse 1 A
Further reading
•Documentation website: https://doc.ruptela.lt/
•Datasheet: FM-Tco4 HCV, FM-Tco4 LCV, FM-Pro4
•User manual: FM-Tco4 HCV, FM-Tco4 LCV, FM-Pro4
•Device Center: https://doc.ruptela.lt/display/AB/Device+Center
•Datasheets and Quick Start guides for harnesses: https://doc.ruptela.lt/display/AB/Harnesses
We highly recommend you read the user manual before using the device.
Legal information
Copyright © 2020 Ruptela. All rights reserved. Reproduction, transfer, distribution or storage of parts or all of the
contents in this document in any form without the prior written permission of Ruptela is prohibited. Other products
and company names mentioned in this document are trademarks or trade names of their respective owners.