Rutland County Morcott wheelie bin storage unit User manual

Assembly Instructions
T
Morcott wheelie bin
storage unit
1
Before you commence the assembly process we recommend that you read these instructions
thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have
the correct components. If for any reason you need assistance, you can find our contact details on the
final page of these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you
use another person to assist you if necessary.
Package contents
Tools required
Per Unit
2 x End panels
1 x Back panel
1 x Front panel
1 x Roof
1 x Metal bar
10 x 65mm screws
2 x 75mm screws
2 x spacer blocks
160mm Coach screws (Multiple units only –
Double x 4, Triple x 8)
Electric screwdriver with No2 Pozidrive bit
Or No2 Pozidrive Screwdriver
10mm socket drive
Morcott wheelie bin storage unit

Morcott wheelie bin storage unit
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
2
Step 1
Step 2
Important: Single units will have a mirror pair of side
panels. A double or triple unit (shown above) will
have a plain left outer end panel and a right panel
with pre-drilled clearance holes as shown above.
The right hand unit when constructing a double store
will have a plain right outer end panel and battens
attached to the left panel as indicated.
Step 3
Step 4
The triple will have 2 x units with 2 mirror plain outer
ends with pre-drilled inner panels as in Steps 1 & 4
and a centre unit with 2 end panels, each with
battens on the outer edge.
The right hand end unit for a triple store with plain
out end panel and pre-drilled inner panel.

Morcott wheelie bin storage unit
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
3
Step 5
Step 6
If you are building a combo unit with recycling
storage, two of the end panels will have supports for
a shelf. These should be paired together as shown
above...
..so the shelf can be supported as shown.
Step 7
Step 8
Stand the appropriate left hand end panel for the unit
you are building upright on a flat, level surface.
Arrange the 2 spacer blocks on the ground, adjacent
to the end panel as shown in the photo above. Now
place a back panel on the blocks, at 90° to the end
panel, aligning the 2 panels ready for fixing.

Morcott wheelie bin storage unit
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
4
Step 9
Step 10
Using the 65mm screws provided, attach the batten
on the back panel to the post of the end panel,
ensuring that the batten remains vertically aligned to
the post.
Now secure the appropriate right hand side panel in
place with 65mm screws in the same manner as you
attached the left side panel.
Step 11
Step 12
Lay the assembly on its back and position the metal
bar as shown across the bottom of the front posts.
(Please note: The metal bar will be screwed to the
side panel during packing for security and will need to
be removed prior to commencing construction.)
Keeping the metal bar flush with the edge of the post,
secure it in position using 2 65mm screws and repeat
for the other side.

Morcott wheelie bin storage unit
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
5
Step 13
Step 14
Carefully lift the assembly back into the normal
position. If you are building a double or triple store,
repeat steps 5 to 11 before arranging the completed
units in their final location, ready to be connected as
shown in the following steps.
Manoeuvre 2 units into position next to each other,
using an assistant if necessary in aligning the front
centre posts...
Step 15
Step 16
...at the top...
...and at the bottom...

Morcott wheelie bin storage unit
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
6
Step 17
Step 18
Now insert a 160mm coach screw into the pre-drilled
hole in the upper front post and drive it fully home,
pulling the 2 units together...
...before adding another one at the bottom of the
front post.
Step 19
Step 20
Add the rear coach screws in the same manner as the
front ones.
For a triple store, follow steps 12 to 17 and add the
remaining unit using 4 coach screws as before.

Morcott wheelie bin storage unit
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
7
Step 21
Step 22
Place the roof section onto the store and align the
rear securing batten with the edge of the rear post as
shown.
Now secure each end of the batten to the posts with
an 75mm screw.
Step 23
Step 24
The roof(s) can now be propped in place as shown,
ready for you to hang the front door(s) using the
hooks already fitted.
Your Morcott wheelie bin storage unit is now
complete.
We hope that you found your product quick and easy to assemble but if not and you require any
further assistance or have any questions you can contact us by telephone on: 01778 440803
Email: [email protected]
www.rutlandcountygardenfurniture.co.uk