S.R.Smith 30" SENTRY LIFEGUARDCHAIR Instruction manual

06-823 MAR17
30” SENTRY LIFEGUARD CHAIR
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
SRS AUSTRALIA, PTY LTD
12 Enterprise St
Richlands QLD 4077
Australia
Phone [phone] • Fax [phone]
www.srsmith.com/au
S.R. SMITH, LLC
CORPORATE HEADQUARTERS
P.O. Box 400 • 1017 S.W. Berg Parkway
Canby, Oregon 97013
USA
Phone [phone] • Fax [phone]
www.srsmith.com

2
TABLE OF CONTENTS
INTRODUCTION ....................................................................................................................... 3
INSTALLED LIFEGUARD STAND STRUCTURAL & INSTALLATION CHECKLIST .................. 3
MAINTENANCE INSTRUCTIONS ............................................................................................. 3
ASSEMBLED LIFEGUARD STAND LAYOUT............................................................................ 4
PARTS LIST.............................................................................................................................. 5
Tools Required ..................................................................................................................... 7
Lifeguard Stand Assembly...................................................................................................... 7

3
INTRODUCTION
DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE
OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY.
PROPER ASSEMBLY, INSTALLATION, USE, AND SUPERVISION ARE ESSENTIAL FOR PROPER
OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY.
CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING
ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS
LISTED IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY
THE INSTALLER PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN
TRANSIT AND THAT A DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE
OVERSTRESSED, IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY
AFFECT THE SAFETY OF THE USER.
INSTALLED LIFEGUARD STAND STRUCTURAL & INSTALLATION CHECKLIST
1. Inspect material for visible cracks or damage.
2. Inspect hardware for missing or damaged parts.
3. Inspect all fasteners to make sure they are fully tightened.
4. Inspect the Lifeguard Stand for rigidity (and attachment if using anchors).
MAINTENANCE INSTRUCTIONS
1. When hosing down the deck, hose your Lifeguard Stand to wash away any dust, dirt or other debris,
which may have accumulated and wipe clean.
2. Be sure that all connections are secure. Tighten hardware if necessary and check for corroded
fasteners.
3. Inspect for visible cracks or other damage.
4. Inspect all parts for evidence of shear, bending yield, or fatigue. Yield is evidenced by discoloration
or fine cracking of the surface.

4
ASSEMBLED LIFEGUARD STAND LAYOUT

5
PARTS LIST
Item #
Part #
Description
Qty.
1
03-500
FOOTREST & STEP, TOP
1
2
03-501
SEAT & BACK PLATE
2
3
03-502
SEAT SUPPORT, SIDE
2
4
03-503
SEAT SUPPORT, REAR
1
5
03-504
SEAT SUPPORT, CENTER
1
6
03-505
SEAT SUPPORT, FRONT
1
7
03-506
BACK SUPPORT, RIGHT
1
8
03-507
BACK SUPPORT, LEFT
1
9
03-508
30" FRONT LEG, RIGHT
1
10
03-509
30" FRONT LEG, LEFT
1
11
03-510
30" REAR LEG, RIGHT
1
12
03-511
30" REAR LEG, LEFT
1
17
03-516
FOOTREST, FRONT
1
18
03-517
30" FOOTREST SIDE, RIGHT
1
19
03-518
30" FOOTREST SIDE, LEFT
1
20
03-519
30" FOOTREST, REAR
1
27
03-525
CUP HOLDER
1
28
03-526
UMBRELLA MOUNT
1
31
03-529
ARM REST, LEFT
1
32
03-530
ARM REST, RIGHT
1
Hardware
33
05-33-120
1/4-20 X 1.5” FLAT HEAD HEX DRIVE SCREW, 316SS
2
34
05-33-121
#8 X 2" SCREW, #2 SQUARE DRIVE, 316SS
45
35
05-33-123
1/4-20 LOCKNUT, 316SS
22
36
05-33-124
1/4 FLAT WASHER, 316SS
22
37
05-33-125
1/4-20 X 2.25” FLATHEAD SCREW, 316SS
20
38
05-33-126
1/4-20 X 1.75" PLASTIC HEAD THUMB SCREW, 316SS
1
39
04-666
30” ANCHOR BRACKET, SENTRY LGC
2

6
Visit srsmith.com for hardware kit and replacement part information.

7
ASSEMBLY INSTRUCTIONS
Tools Required
1. #2 Square Drive Bit
2. 5/32” Allen Wrench
3. 7/16” Ratchet or Wrench
Lifeguard Stand Assembly
1.Attach part (2) to part (3) as shown using screws (34).
2.Attach part (3) to assembly using screws (34).

8
3.Attach part (4) to assembly with screws (34).
4.Attach part (5) with notch in direction shown to assembly using screws (34).
5.Attach part (6) to assembly with screws (34).

9
6.Seat Bottom Assembly should look like the pictures below when finished. Next make Seat
Back Assembly.
7.Attach part (2) to part (8) using screws (34).
8.Attach part (7) to assembly using screws (34).

10
9.Seat Back Assembly should look like the pictures below when finished. Next make
Footrest Assembly.
10.Attach part (20) to part (18) using screws (34).
11.Attach part (19) to assembly using screws (34).
12.Attach part (17) to assembly using screws (34).

11
13.Attach part (1) to assembly using screws (34).
14.Finished Footrest Assembly should look like the picture below. Next attach legs using
last 3 assemblies.
15.Attach Seat Back Assembly, Seat Bottom Assembly, and Footrest Assembly to leg (11)
as shown using nuts (35), washers (36), and screws (37).

12
16.Next, attach leg (9) to assembly using nuts (35), washers (36), and screws (37).
17.Flip chair and attach leg (12) to assembly using nuts (35), washers (36), and screws (37).

13
18.Next attach leg (10) to assembly using nuts (35), washers (36), and screws (37).
19.Now attach left arm (31) to assembly using screws (34).

14
20.Attach right arm (32) to assembly with screws (34).
21.Install cup holder (27) using screws (34).

15
22.Now install umbrella mount (28) using screws (34).
23.Screw in thumb screw (38), do not tighten.

16
24.Install Anchor (39) using Bolt (33), Washer (36), and Nut (35).
25. Assembly complete. Now, go back through assembly to ensure all hardware has been
properly tightened.
Warning: Chair required to be anchored to deck when using umbrella.
Recommended Anchor: When installing in concrete use type 316 stainless steel concrete anchor,
3/8” in diameter (not included).

A