Sabine Rt-7000 User manual

Sabine Professional Rack Tuner

Operating Guide

Quick Setup Directions

1.1.

1. Power on the Sabine RT-7000 or RT-7100 Rack Tuner.

2.2.

2. Plug your instrument into one of the ¼-inch input connectors.

3.3.

3. Pluck the string you wish to tune—the nearest note will be displayed in the Note LED display and the distance to

in-tune (in relation to that note) will be shown by the number of Flat or Sharp LEDs lit.

4.4.

4. Adjust the tuning of the string until the In-Tune LED lights.

Congratulations! You have the world’s most advanced rack-mount

instrument tuner. Sabine RT-7000 Series Professional Rack Tuners

are road-worthy tuners that are fast, accurate, versatile and easy-

to-read.

RT-7100 Features

Swoop LED DisplaySwoop LED Display

Swoop LED Display: Gives you the best visual cue for easy

tuning, especially from a distance. It works like a bar graph of

your pitch, sweeping up for sharp & down for flat.

Bright & Easy to ReadBright & Easy to Read

Bright & Easy to Read: The huge note indicator is visible from

across the stage, even if you’re wearing shades!

Dual Tuning ModesDual Tuning Modes

Dual Tuning Modes: Never again will tuning be a dreary pre-

lude to greater things with Sabine’s Dual Mode LED tuning dis-

play. Standard Mode gives you a bar graph reading of your

pitch. Strobe Mode shows moving sweep of pitch. Both are

more accurate than conventional needle-style displays.

Two Independent ChannelsTwo Independent Channels

Two Independent Channels: Select on front panel or with op-

tional foot switch (model # RTPED2).

SmartSwitchSmartSwitch

SmartSwitch™ A/B CircuitA/B Circuit

A/B CircuitA/B Circuit

A/B Circuit: The RT-7100 senses your input/

output configuration and automatically adjusts the A/B switch

to conform to your setup. Have two guitars and one amp? Or

one guitar and two amps? No problem – just plug ‘em in and

switch between guitars or amps depending your setup!*

&Flat TuneFlat Tune

Flat TuneFlat Tune

Flat Tune: Set the tuner to any of four different flat tunings: ½,

1, 1½, or 2 steps below standard pitch. Play and tune your

guitar normally but at a lower overall pitch!

CalibrationCalibration

Calibration: Change the overall calibration of the tuner from

435 to 445 Hz.

MuteMute

Mute: Mute your instrument for silent tuning – select on the

front panel or with the optional foot switch.

Built-in MicBuilt-in Mic

Built-in Mic: Tunes almost any acoustic instrument.

Dual JacksDual Jacks

Dual Jacks: Front and back panel input/output jacks.

Automatic Note & Sharp/Flat SensingAutomatic Note & Sharp/Flat Sensing

Automatic Note & Sharp/Flat Sensing

ChromaticChromatic

Chromatic: 7-Octave range, perfect for guitar and bass; works

all the way down to a low A!

Heavy-Duty Metal CaseHeavy-Duty Metal Case

Heavy-Duty Metal Case: Built for heavy road use.

Built-in power supplyBuilt-in power supply

Built-in power supply

Power-off MemoryPower-off Memory

Power-off Memory: Recalls previous Calibration & Flat-tune set-

tings.

RT-7000 Features

All the same great features except:

♦Standard A/B switch between channels

♦Output jacks on back panel only

♦Tunes via instrument plug-in only (no built-in mic)

Both the RT-7000 & RT-7100 Professional Rack Tuners are Made in the USAMade in the USA

Made in the USAMade in the USA

Made in the USA

and come with Sabine’s famous two-year warranty.

♦If you have difficulty getting a note to register on

the tuner, touch the other strings lightly to stop their

sympathetic vibrations.

♦Use good strings. Old strings lose their uniformity

and do not vibrate evenly. Remember to stretch your

new strings out; new strings stretch flat as you play.

♦All sources of friction cause tuning problems. For

example, if the slot in an instrument’s nut is too

tight, the string will be pulled flat as it is played. A

tight nut (or capo) will cause the string’s pitch to

change in steps rather than evenly.

♦Avoid pressure on the instrument while tuning. Even

moderate pressure on the neck of a guitar will cause

a noticeable change in pitch. Also, press the strings

straight down to the fingerboard. Bending the

strings sideways is very common, especially on dif-

ficult chords, but causes the strings to be pulled

sharp.

♦Pluck one string at a time.

♦Pluck the instrument once per second to keep the

note “fresh” while you are tuning. Notes go notice-

ably flat a second or two after being plucked. If tun-

ing a higher-pitched instrument (such as a mando-

lin), pluck a little faster; for a lower-pitched instru-

ment (such as a bass), pluck slower.

♦Do not pluck loudly. Generally light to medium

volumes provide purer tones that are easier for

tuners to analyze.

♦Fingernails and flat picks add overtones and slow

the tuning process.

♦Tune from a pitch that is flat up to the pitch you de-

sire. This procedure removes any slack in the gears

of the instrument’s tuning heads. If you tune from

sharp to in tune, the gears will slip as you play,

and the instrument will go flat after a few minutes

of playing.

Instrument Tuning Tips

*NOTE: A/B switch does not combinecombine

combinecombine

combine signals from inputs or outputs. Only one output

is active at a time.

Using your RT-7100 Rack Tuner

Inputs/Outputs

The RT-7100RT-7100

RT-7100RT-7100

RT-7100 Rack Tuner has two channels (A or B) with

inputs (labeled “INST”) for these channels on both the front

panel and back panel. NOTENOTE

NOTENOTE

NOTE: Only one input jack (front or

back) per channel can be used at a time.

The Rack Tuner Outputs are labeled “AMP.” The RT-7100RT-7100

RT-7100RT-7100

RT-7100

has outputs located on the back and on the front panel. NOTENOTE

NOTENOTE

NOTE:

only one input or output jack (front or back panel) per channel

can be used at a time.

Foot Pedal

The RT-7100RT-7100

RT-7100RT-7100

RT-7100 has ¼-inch TRS connectors for a two-switch pedal

(model # RTPED2). Use the Foot Pedal to toggle between Chan-Chan-

Chan-Chan-

Chan-

nels Anels A

nels A & BB

B and/or to MuteMute

MuteMute

Mute the tuner output. Connectors are located

on both the front and back panels (use only one pedal at a time).

When a foot pedal is connected, all front panel switches still operate.

NOTE: if you use your own pedal, the switches must be momentary,

not latching.

SmartSwitch™ A/B Display

This LED array displays your input/output con-

figuration and the signal path of the SmartSwitchSmartSwitch

SmartSwitchSmartSwitch

SmartSwitch

circuit. As you plug in your guitar(s) and amp(s)

you will immediately see the corresponding A or

B INST or AMP LED light on the Display.

When you touch the A/B switch, the signal path LEDs will clearly

show the signal routing configuration of the SmartSwitchSmartSwitch

SmartSwitchSmartSwitch

SmartSwitch (see

diagrams on page 4). And, at the same time, the A or B input

LED will flash to indicate the active tuner channel.

Front Panel Switches

The A/B switch performs two func-

tions simultaneously.

Tuner Channel Switching:Tuner Channel Switching:

Tuner Channel Switching:

Tapping the front-panel A/B

button switches the tuner to either the A or B input, and the

appropriate LED flashes on the SmartSwitchSmartSwitch

SmartSwitchSmartSwitch

SmartSwitch display to show

you which channel is active in the tuner.

Signal Channel Routing:Signal Channel Routing:

Signal Channel Routing:

Tap-

ping the A/B switch also routes the in-

put/output signal path to match your

rig. Use the SmartSwitchSmartSwitch

SmartSwitchSmartSwitch

SmartSwitch A/B circuit

with any of the following configurations:

Use the front panel Flat TuneFlat Tune

Flat TuneFlat Tune

Flat Tune ButtonButton

ButtonButton

Button

to quickly transpose your guitar down

from standard tuning — great for

those dark-n-heavy Eband D tunings. The front panel Flat TuneFlat Tune

Flat TuneFlat Tune

Flat Tune

StepsSteps

Steps scale shows the number of steps or tones below stan-

dard tuning. NN

NOTEOTE

OTEOTE

OTE: The RT-7100 display has dedicated LEDs

that show Flat Tune status. The Flat Tune LEDFlat Tune LED

Flat Tune LEDFlat Tune LED

Flat Tune LED for the current

setting will always be lit. The “0” LED signifies standard tuning;

each position to the left of zero represents ½ tone down from

standard tuning. Press the Flat TuneFlat Tune

Flat TuneFlat Tune

Flat Tune ButtonButton

ButtonButton

Button once to move the

status light one LED to the left. For example, to flat tune your

guitar down two half tones, tap the Flat TuneFlat Tune

Flat TuneFlat Tune

Flat Tune ButtonButton

ButtonButton

Button twice. The

Flat TuneFlat Tune

Flat Tune ButtonButton

ButtonButton

Button will light and the Flat TuneFlat Tune

Flat TuneFlat Tune

Flat Tune LEDLED

LEDLED

LED will move two

positions to the left.

Tapping the front panel’s Strobe But-Strobe But-

Strobe But-Strobe But-

Strobe But-

tonton

ton toggles the display mode between

StandardStandard

Standard and StrobeStrobe

StrobeStrobe

Strobe mode.

Standard Mode:Standard Mode:

Standard Mode:

(resembles a bar graph)

Up to 8 sharp or

flat LEDs will light up to indicate the degree of sharpness or flat-

ness in cents. As the played note gets closer to the note indi-

cated by the Note LEDNote LED

Note LEDNote LED

Note LED, the corresponding sharp or flat LEDs will

dim and turn off one by one until the green “in tune” LED lights.

Strobe ModeStrobe Mode

Strobe Mode::

LEDs strobe left to indicate flat, right to

indicate sharp. Strobe speed is a function of the distance the

played note is from being in tune. A pitch far from the closest

note (as indicated by the Note LEDNote LED

Note LEDNote LED

Note LED) will strobe quickly. As the

played note gets closer to the note indicated by the Note LEDNote LED

Note LEDNote LED

Note LED,

the strobe effect will slow down and eventually stop for in tune.

NOTENOTE

NOTE: As in all strobe tuners, it can be difficult to get the strobe

effect to stop completely. This is due to the extreme accuracy

of the strobe tuner and the fluctuation in string vibration fre-

quency as it varies from “first plucked” to sustained note.

Use the Front Panel Calibrate But-Calibrate But-

Calibrate But-Calibrate But-

Calibrate But-

tonton

ton to tune your instrument to a

pitch basis other than A = 440 Hz.

NOTENOTE

NOTE: The RT-7100 display has dedicated LEDs that show

calibration status. The Calibration LEDCalibration LED

Calibration LEDCalibration LED

Calibration LED for the current setting

will always be lit. Press the Calibrate ButtonCalibrate Button

Calibrate ButtonCalibrate Button

Calibrate Button once to move the

status light one LED to the right (past 445 Hz, the LED will

cycle to 435 Hz). For example, if you wish to recalibrate the

tuner from standard A = 440 Hz to A = 442 Hz, tap the CalibrateCalibrate

CalibrateCalibrate

Calibrate

ButtonButton

Button twice. The Calibrate ButtonCalibrate Button

Calibrate ButtonCalibrate Button

Calibrate Button and the Calibration LEDCalibration LED

Calibration LEDCalibration LED

Calibration LED above

442 Hz will remain lit while the tuner is calibrated to A = 442 Hz.

The Mute ButtonMute Button

Mute ButtonMute Button

Mute Button mutes both outputs

for silent tuning. The mute function can

also be operated with a foot switch.

Front Panel Microphone

The front panel of the RT-7100 is equipped with a micro-

phone for acoustic instrument tuning without a ¼-inch

cord. This microphone is disconnected whenever any of

the inputs has a connector plugged into it. Signal fromSignal from

Signal fromSignal from

Signal from

the microphonethe microphone

the microphone will notwill not

will notwill not

will not pass to any of the outputs.pass to any of the outputs.

pass to any of the outputs.pass to any of the outputs.

pass to any of the outputs.

One guitar into one amp out:

Simple setup, you don’t need

the A/B Function

One guitar, 2 amp outputs:

Switches outputs

Two guitars, one amp

output: Switches inputs

Two separate rigs: 2

guitars into 2 amp

outs: Switches both

inputs & outputs

between channels

A or B

Quick Setup Directions

1.1.

1. Power on the Sabine RT-7000 or RT-7100 Rack Tuner.

2.2.

2. Plug your instrument into one of the ¼-inch input connectors.

3.3.

3. Pluck the string you wish to tune—the nearest note will be displayed in the Note LED display and the distance to

in-tune (in relation to that note) will be shown by the number of Flat or Sharp LEDs lit.

4.4.

4. Adjust the tuning of the string until the In-Tune LED lights.

RT-7100

RT-7100 Front PanelRT-7100 Front Panel

RT-7100 Front Panel

1 Instrument Inputs (See NOTENOTE

NOTENOTE

NOTE on

last page)

2 Outputs

3 Pedal Switch

4 SmartSwitch™ A/B Display

5 A/B Display

6 Function Buttons

7 Note Display

8 Flat Tune Step LEDs

9 Calibration Scale LEDs

1010

10 In Tune LED

1111

11 Power Switch

688

1010

366

21111

1111

NOTE: A/B switch does not combine signals from

inputs or outputs. Only one output is active at a time.

RT-7000

Quick Setup Directions

1.1.

1. Power on the Sabine RT-7000 or RT-7100 Rack Tuner.

2.2.

2. Plug your instrument into one of the ¼-inch input connectors.

3.3.

3. Pluck the string you wish to tune—the nearest note will be displayed in the Note LED display and the distance to

in-tune (in relation to that note) will be shown by the number of Flat or Sharp LEDs lit.

4.4.

4. Adjust the tuning of the string until the In-Tune LED lights.

Using your RT-7000 Rack Tuner

Inputs/Outputs

The RT-7000 Rack Tuner has two channels (A or B) with in-

puts (labeled “INST”) for these channels on both the front panel

and back panel. NOTENOTE

NOTENOTE

NOTE: Only one input jack (front or back)

per channel can be used at a time. The Rack Tuner Outputs

are labeled “AMP.” The RT-7000 has Outputs for channels A

and B located on the back panel of the unit.

Foot Pedal

The RT-7000RT-7000

RT-7000RT-7000

RT-7000 has ¼-inch TRS connectors for a two-switch

pedal (model # RTPED2). Use the Foot Pedal to toggle between

Channels A & BChannels A & B

Channels A & B and/or to MuteMute

MuteMute

Mute the tuner output. Connectors

are located on both the front and back panels (only one pedal

should be used at a time). When a foot pedal is connected, all

front panel switches still operate. NOTE: if you use your ownNOTE: if you use your own

NOTE: if you use your ownNOTE: if you use your own

NOTE: if you use your own

pedal, the switches must be momentary, not latching.pedal, the switches must be momentary, not latching.

pedal, the switches must be momentary, not latching.

A/B Switch Display

This LED array displays your input/output con-

figuration and the signal path of the A/BA/B

A/BA/B

A/B circuit.

As you plug in your guitar(s) and amp(s) you will

immediately see the corresponding A or B INST

or AMP LED light on the Display.

When you touch the A/B switch, the signal path LEDs will clearly

show the input/output configuration. And, at the same time, the

A or B input LED will flash to indicate the active tuner channel.

Front Panel Switches

The front-panel A/B ButtonA/B Button

A/B ButtonA/B Button

A/B Button (or optional

pedal switch) toggles the tuner between A

or B input/output. The current selection is

displayed on the A/B Switch DisplayA/B Switch Display

A/B Switch DisplayA/B Switch Display

A/B Switch Display.

Use the front panel Flat Tune ButtonFlat Tune Button

Flat Tune ButtonFlat Tune Button

Flat Tune Button

to quickly transpose your guitar down

from standard tuning — great for those

dark-n-heavy Eband D tunings. NOTENOTE

NOTENOTE

NOTE: The RT-7000RT-7000

RT-7000RT-7000

RT-7000 display

uses the tuning indicator LEDs in conjunction with the Flat Tune

Steps legend to display Flat Tune status. The LED below the

“0” of the Flat Tune Steps legend signifies standard tuning;

each position to the left of zero represents ½ tone down from

standard tuning. The current Flat Tune status will be displayed

briefly the first time the Flat Tune ButtonFlat Tune Button

Flat Tune ButtonFlat Tune Button

Flat Tune Button is pressed. While the

status LED remains lit, each subsequent pressing will move

the setting one LED to the left. For example, to flat tune your

guitar down two half tones, press the Flat Tune ButtonFlat Tune Button

Flat Tune ButtonFlat Tune Button

Flat Tune Button once

to display the current setting, and then two more times to lower

the setting two half tones. The LED below the current flat-tune

setting will remain lit briefly. The Flat Tune ButtonFlat Tune Button

Flat Tune ButtonFlat Tune Button

Flat Tune Button will remain lit

whenever the tuner is set to other than standard tuning.

Tapping the front panel’s Strobe But-Strobe But-

Strobe But-Strobe But-

Strobe But-

tonton

ton toggles the display mode between

StandardStandard

Standard and StrobeStrobe

StrobeStrobe

Strobe mode.

Standard Mode:Standard Mode:

Standard Mode:

(resembles a bar graph)

Up to 8 sharp or

flat LEDs will light up to indicate the degree of sharpness or flat-

ness in cents. As the played note gets closer to the note indi-

cated by the Note LED, the corresponding sharp or flat LEDs will

dim and turn off one by one until the green “in tune” LED lights.

Strobe Mode:Strobe Mode:

Strobe Mode:

LEDs strobe left to indicate flat, right to indi-

cate sharp. Strobe speed is a function of the distance the

played note is from being in tune. A pitch far from the closest

note (as indicated by the Note LED) will strobe quickly. As the

played note gets closer to the note indicated by the Note LEDNote LED

Note LEDNote LED

Note LED,

the strobe effect will slow down and eventually stop for in tune.

NOTENOTE

NOTE: As in all strobe tuners, it can be difficult to get the strobe

effect to stop completely. This is due to the extreme accuracy

of the strobe tuner and the fluctuation in string vibration fre-

quency as it varies from “first plucked” to sustained note.

Use the Front Panel CalibrateCalibrate

CalibrateCalibrate

Calibrate ButtonButton

ButtonButton

Button

tune your instrument to a pitch other than

A = 440 Hz, or if you want to use alter-

nate scales. NOTENOTE

NOTENOTE

NOTE: The RT-7000 display uses the tuning indica-

tor LEDs in conjunction with the Calibration Legend to display

calibration status. The current calibration status will be displayed

when the CalibrateCalibrate

CalibrateCalibrate

Calibrate ButtonButton

ButtonButton

Button is pressed once. While the status LED

remains lit, each subsequent pressing will move the status light

one LED to the right (past 445 Hz, the LED will cycle to 435 Hz).

For example, if you wish to recalibrate the tuner from standard A

= 440 Hz to A = 442 Hz, tap the CalibrateCalibrate

CalibrateCalibrate

Calibrate ButtonButton

ButtonButton

Button once to display

the current setting (A = 440 Hz), and then twice more. The 442

Hz LED will remain lit briefly. The CalibrateCalibrate

CalibrateCalibrate

Calibrate ButtonButton

ButtonButton

Button will remain lit

whenever the tuner is calibrated to other than A = 440 Hz.

The Mute ButtonMute Button

Mute ButtonMute Button

Mute Button mutes both outputs

for silent tuning. The mute function can

also be operated with a foot switch.

1 Instrument Inputs (See NOTENOTE

NOTENOTE

NOTE on last page)

2 Outputs

3 Pedal Switch

4 SmartSwitch™ A/B Display

5 A/B Display

6 A/B Switch

7 Function Buttons

8 Note Display

9 Flat Tune Step LEDs (RT-7100 only)

1010

10 Flat Tune Step markers (RT-7000)

1111

11 Calibration Scale LEDs (RT-7100 only)

1212

12 Calibration Scale Markers (RT-7000)

1313

13 In Tune LED

1414

14 AC Power Cord & Fuse Holder

1515

15 Power Switch

RT-7000 Front PanelRT-7000 Front Panel

RT-7000 Front Panel 1212

1212

155

51010

1010

31515

1515

NOTE: A/B switch

does not combine sig-

nals from inputs or

outputs. Only one out-

put is active at a time.

Sabine.com

Sabine, Inc.

13301 NW US Highway 441

Alachua, Florida 32615 USA

Tel: (386) 418-2000

Fax: (386) 418-2001

MADE IN USAMADE IN USA

MADE IN USA

FCC Statement:FCC Statement:

FCC Statement:

This device complies with Part 15, Class B, of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference; and (2) This device must accept any

interference received, including interference that may cause undesired operation.

Warning:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

SPECIFICATIONSSPECIFICATIONS

SPECIFICATIONS

RANGEANGE

ANGEANGE

ANGE::

: Chromatic, 7 octaves

ACCURACYCCURACY

CCURACYCCURACY

CCURACY::

: ± 1 cent (quartz crystal)

OWEROWER

OWER

NPUTNPUT

NPUT

100 - 130 VAC, 50/60 Hz, 0.1A 15 Watt input

200 - 240 VAC, 50/60 Hz, 0.1A 15 Watt input

FUSEUSE

USEUSE

USE::

100 - 130 VAC models: 0.100 A Type T slow blow fuse

200 - 240 VAC models: 0.050 A Type T slow blow fuse

DIMENSIONSIMENSIONS

IMENSIONSIMENSIONS

IMENSIONS::

: 1-U rack mount; 19 x 1.75 x 4.5 inches nominal

(rack mountable); 48.3 x 4.45 x 11.43 cm nominal

WEIGHTEIGHT

EIGHTEIGHT

EIGHT::

: 3.75 lbs. (1.7 kg) nominal

SCALECALE

CALECALE

CALE::

: Even-tempered, 12 notes per octave

INPUTSNPUTS

NPUTSNPUTS

NPUTS::

: RT-7100: A & B channels, ¼-inch front & back

RT-7000: A & B channels, ¼-inch front & back

OUTPUTSUTPUTS

UTPUTSUTPUTS

UTPUTS::

: RT-7100: A & B channels, ¼-inch front & back

RT-7000: A & B channels, ¼-inch back only

Specifications subject to change without notice.

(piano: 1st octave A to 6th octave C)

RT7000-Series-OpGd-4PDF-020531.pmd - hto

Rack Tuner Back PanelRack Tuner Back Panel

Rack Tuner Back Panel

NOTENOTE

NOTE: use either FrontFront

FrontFront

Front or BackBack

BackBack

Back panel inputs per channel, NOT BOTHNOT BOTH

NOT BOTHNOT BOTH

NOT BOTH

(RT-7000 & RT-7100)(RT-7000 & RT-7100)

(RT-7000 & RT-7100)

122

NexFX Pedal Tuner (NEX-5000)NexFX Pedal Tuner (NEX-5000)

NexFX Pedal Tuner (NEX-5000)

The Sabine NEX-5000 Pedal Tuner captures notes fast and accu-

rately, and holds them longer for quick and easy tuning. The NexFX

Pedal Tuner has an 11-LED display simulates a bar graph that sweeps

to the right or left showing how sharp or flat the note is, a Flat-Tune

function that lets you quickly transpose from standard tuning and a

Calibrate function allows for tuning to other than A = 440 Hz, and two

parallel outputs—that means the same signal can split to different

sound processing equipment or to other Sabine NexFX Pedals.

NexFX FuzzStortion™ (NEX-5100)NexFX FuzzStortion™ (NEX-5100)

NexFX FuzzStortion™ (NEX-5100)

From warm and fuzzy to head-crushing, this one has all the distortion

you need! Blend the perfect mix, from 60s fuzz tone to end-of-the-

millennium bombast. Carve out a heaping scoop of midrange while

leaving a sparkling top and a thunderous bottom—or leave the mids

intact and tweak the treble. You’ll love the buzz from this fuzz!

♦♦

♦Fuzz and Distortion in one pedalFuzz and Distortion in one pedal

Fuzz and Distortion in one pedalFuzz and Distortion in one pedal

Fuzz and Distortion in one pedal

♦♦

♦Two tone controls for optimal sonic contouringTwo tone controls for optimal sonic contouring

Two tone controls for optimal sonic contouringTwo tone controls for optimal sonic contouring

Two tone controls for optimal sonic contouring

♦♦

♦Broad range of sound, from light crunch to thick metal distortionBroad range of sound, from light crunch to thick metal distortion

Broad range of sound, from light crunch to thick metal distortionBroad range of sound, from light crunch to thick metal distortion

Broad range of sound, from light crunch to thick metal distortion

NexFX Overdrive (NEX-5200)NexFX Overdrive (NEX-5200)

NexFX Overdrive (NEX-5200)

Boost it! Crunch it! This NexFX is fat, lean, clean, mean, dirty, sweet,

and in-between. With squeaky clean Sustain or pumped up Over-

drive, plus Mid, Treble, and Level controls, you can change moods

faster than a jilted lover on a bad hair day. Make your leads sing!

♦♦

♦Rippin’ analog overdrive soundRippin’ analog overdrive sound

Rippin’ analog overdrive soundRippin’ analog overdrive sound

Rippin’ analog overdrive sound

♦♦

♦Sustain control for extra punch in your leadSustain control for extra punch in your lead

Sustain control for extra punch in your leadSustain control for extra punch in your lead

Sustain control for extra punch in your lead

♦♦

♦Threshold control for touch-sensitive effectThreshold control for touch-sensitive effect

Threshold control for touch-sensitive effectThreshold control for touch-sensitive effect

Threshold control for touch-sensitive effect

NexFX StereoChorus (NEX-5300)NexFX StereoChorus (NEX-5300)

NexFX StereoChorus (NEX-5300)

The greatest event in the history of swirl since chocolate met vanilla in a

Kansas twister. Lush swirling choruses with control for Depth, Speed,

Wet/Dry Mix (no, not for your dog), Tone, and Sabine’s unique Stereo

Auto-Pan. Your head will spin as your guitar gently whirls. It’s Taber-

nacle Choir awesome!

♦♦

♦True stereo effects; two outputsTrue stereo effects; two outputs

True stereo effects; two outputsTrue stereo effects; two outputs

True stereo effects; two outputs

♦♦

♦AutoPan function sweeps between outputs at adjustable rateAutoPan function sweeps between outputs at adjustable rate

AutoPan function sweeps between outputs at adjustable rateAutoPan function sweeps between outputs at adjustable rate

AutoPan function sweeps between outputs at adjustable rate

♦♦

♦Mix control let's you balance effect and dry soundMix control let's you balance effect and dry sound

Mix control let's you balance effect and dry soundMix control let's you balance effect and dry sound

Mix control let's you balance effect and dry sound

NexFX Compressor (NEX-5400)NexFX Compressor (NEX-5400)

NexFX Compressor (NEX-5400)

Now you can cut through the mix like a silk knife or a raging chain saw,

without overpowering the rest of the band. Ratio, Threshold, Level, At-

tack, and Tone Controls allow you to put 10 tons of whammy into a 1

pound mix. Add punch without distortion—your sound will be clean, fat

and chillin’. Like your first kiss in the back of the movie theatre, it’s so

smooooth and drawn out!

♦♦

♦Famous Sabine compressorFamous Sabine compressor

Famous Sabine compressorFamous Sabine compressor

Famous Sabine compressor

♦♦

♦Control Ratio, Threshold and AttackControl Ratio, Threshold and Attack

Control Ratio, Threshold and AttackControl Ratio, Threshold and Attack

Control Ratio, Threshold and Attack

♦♦

♦Clean sustain for punch without distortionClean sustain for punch without distortion

Clean sustain for punch without distortionClean sustain for punch without distortion

Clean sustain for punch without distortion

Evolution couldn’t get this far.

Step on the NEX Revolution in Pedal Effects!

RT-7000 Series Back PanelRT-7000 Series Back Panel

RT-7000 Series Back Panel

1 Instrument Inputs (See NOTENOTE

NOTENOTE

NOTE)

2 Outputs

3 Pedal Switch

4 AC Power Cord & Fuse Holder

(built into AC Plug Housing)

SABINE TWO-YEAR WARRANTYSABINE TWO-YEAR WARRANTY

SABINE TWO-YEAR WARRANTY

If your RT-7000 or RT-7100 Professional Rack Tuner fails because of a manufacturing defect within TWO YEARS from the date of originalf your RT-7000 or RT-7100 Professional Rack Tuner fails because of a manufacturing defect within TWO YEARS from the date of original

f your RT-7000 or RT-7100 Professional Rack Tuner fails because of a manufacturing defect within TWO YEARS from the date of originalf your RT-7000 or RT-7100 Professional Rack Tuner fails because of a manufacturing defect within TWO YEARS from the date of original

f your RT-7000 or RT-7100 Professional Rack Tuner fails because of a manufacturing defect within TWO YEARS from the date of original

purchase, please return, postage prepaid, to SABINE for a replacement with a new or reconditioned product. This warranty does not coverpurchase, please return, postage prepaid, to SABINE for a replacement with a new or reconditioned product. This warranty does not cover

purchase, please return, postage prepaid, to SABINE for a replacement with a new or reconditioned product. This warranty does not cover

damage caused by accident or misuse. You must include your full name, address, proof of purchase and the nature of the defect.damage caused by accident or misuse. You must include your full name, address, proof of purchase and the nature of the defect.

damage caused by accident or misuse. You must include your full name, address, proof of purchase and the nature of the defect.

This warranty is in lieu of all other warranties, expressed or implied. This warranty gives you specific legal rights which vary from state toThis warranty is in lieu of all other warranties, expressed or implied. This warranty gives you specific legal rights which vary from state to