Sable SA-HF034 User manual

EN
READ FOLLOWING INSTRUCTIONS AND WARNINGS BEFORE USE
IMPORTANT
· Household use only.
· The voltage used must be AC 110 – 120V for US/CA, AC 220V-240 for EU/UK, and
AC 100V for Japanese specifications.
· This pump cannot be used continuously for more than 10 minutes.
· Keep the pump out of reach of children.
· Keep the air inlet / exhaust ventilation unblocked all the time.
· To reduce the risk of fire and electric shock, do not use the pump to fan speed
control valves and other equipment.
· When the pump is not in use, please unplug the power supply.
· This pump has limiting temperature protection, when the pump has been working
for a long time, it will lead to overheat and stop working to protect the pump. Please
take a break for 5 minutes before your next use.
Warning
· To reduce electrical risk, please contact a qualified electrician for repairs.
· Refer to this guide when using the pump to inflate inflatable items.
· Do not leave the product unattended when it’s in use. Do not use it in wet
environments.
· When using the product, do not allow sand, gravel, or small objects entering the
inflation and deflation ports.
· When the pump is working, do not look directly inside the inflation and deflation
ports.
· Do not ever try to put hands or fingers inside the inflation and deflation ports.
· Do not disconnect the wire with wet hands.
· When the product is not in use, turn it off and unplug from power source.
· If the product is damaged, especially if the power cord is damaged, please stop
using the pump. Do not put liquid in the pump.
· The pump requires regular maintenance.
· Do not use the product near hot objects, such as electric stove, oven, to prevent
melting.
· Stop using the pump for at least 5 minutes after continuous use of 10 minutes.
· This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
· Children should be supervised to ensure that they do not play with the appliance.
· If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
Inflating the Bed
Make sure the extra safety valve closed tightly prior to inflation by firmly pushing the
tab down.
1. Unroll the bed on a flat clean area. Be sure the indented side is facing up and the
other side on the floor.
2. Open the cord storage holder, plug into a power source. Turn the knob clockwise to
the INFLATE position. It takes 3 to 5 minutes to inflate.
3. When the airbed is fully inflated, turn the knob counterclockwise to OFF to shut off
the motor. Put the cord back into cord holder.
Deflating the Bed
1. To deflate, remove the protector and make sure nothing is on top of the
mattress.Take out the cord and plug into a power source. Turn the knob counter-
clockwise to the DEFLATE position.
2. When done, rotate the knob to OFF, and put the cable back into the cord holder.
3. Open the air valve to let the remaining air out, then roll the bed up for easy storage.
Using the protector
Spread the protector and cover it onto the air mattress.
SABLE AIR MATTRESS WITH PROTECTOR
User Guide

Cleaning and Storing
1. Use a damp cloth and wipe the surface to clean off any dirt and debris. Be sure to
store after the bed is dry. Do not use harsh detergents that may damage the airbed.
2. Once deflated, carefully fold the airbed and store in a cool, dry area.
1 2 3
45
Bottom
Folding
Direction
Place Bed into the Carry Bag
Folding
Direction
Folding
Direction Folding
Direction
Caution
• Keep away from heat sources and fire.
• Avoid sharp and rough objects.
• Do not over-inflate or jump on the airbed.
• Not a lifesaving device, do not use it in water.
• The product can be used by children aged 8 years or above.
Don’t drag the deflated bed on the ground.
Additional Information
PVC Smell
There may be some PVC smell when you receive the airbed, which will be gone in 1 to
2 days.
Air Leakage
Check whether the extra safety valve is securely tightened first, if air leakage occurs.
Repair the Air Leakage
1. Wipe the inflated bed with mild soapy water to locate the possible leaking area. Air
bubbles will form from the leaking area. Do not submerge the airbed in water.
2. Clean the leaking area from all dirt and dry it completely. Deflate the bed.
3. Cut a suitable size of repair patch, press it firmly over the leaking area.
4. Wait for 1 hour before inflation.
5. Please be noted that the repair patch can only stick on bottom of the airbed
instead of the flocked top or side.
Model: SA-HF034
NORTH AMERICA
E-mail：
[e-mail]
[e-mail]
Tel : [phone] (Monday-Friday: 9:00 – 17:00 PST)
Address: 46724 Lakeview Blvd, Fremont, CA 94538
EUROPE
E-mail：
[e-mail]
[e-mail]
[e-mail]
[e-mail]
[e-mail]
EU Importer: ZBT International Trading GmbH
Address: Halstenbeker Weg 98C, 25462 Rellingen, Deutschland
ASIA PACIFIC
[e-mail]
Te l : 03-5542-0238（10-18時/土日祝除く）
JP Importer: 株式会社SUNVALLEYJAPAN
Address: 〒104-0032東京都中央区八丁堀３丁目18-6PMO京橋東９F

成品尺寸：100*145mm
公差:±1mm
材质：128G铜版纸
折页