SACAGAWEA DESIGNS VK-1228 Manual

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View 10’
10’
VK-1228 - 10’ x 10’ Display
REV 11/2022
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2022
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
1) Mounting plate & wing nuts,
in packed position.
6) Place fixed counter bolts
into mounting plate, then
secure using wing nuts.
Completed Assembly
Counter Attachment
Wing Nut
Fixed
Bolts
Mounting
Plate [11A]
10
11
Counter
Attach mounting plate to curved extrusion
[10], using bolt. Insert fixed bolts, located
on underside of counter, into holes of flange
plate. Secure with wing nuts.
Mounting Plate
w/ Wing Nuts
Bottom view
of counter
10
11
Wing Nut
Wing Nut
Counter
2) Mounting plate bolt in,
packed position.
10
11
Bolt
5) Tighten bolt, using hex tool,
to secure.
Mounting Plate
Bolt
3) Place mounting plate onto
[10] then tighten bolt, part
way, allowing some rotation
for final positioning.
4) Place fixed counter bolts
into mounting plate, then lift
counter to re-tighten bolt.
Mounting Plate
10
Fixed
Counter
Bolt
Fixed
Counter
Bolt
Hex Tool
Keep mounting plate [11A] and wing nuts
attached to counter, when packing.
Keep bolt attached to [10], when packing.
Bolt
Mounting
Plate
Bottom view of counter Bottom view of counter
Counter Assembly

© 2022
Case 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
A,A
B,B
6A
3A,3B
2B,2A
6B
4A, 4B, 5A, 5B
Level 2 Level 3Level 1 (Bottom Level)
Wing Panels
Round
Sign
Assembled
Header
Shelf
Graphics
Lights
Setup Hardware
Monitor Mount
Literature Trays
Base
Plates
10A 11
10
11A
Counter
Top
Case Packing

© 2022
Case 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
3 3
Assembled
Pedestal
Side
Assembled
Pedestal
Side
Level 2 Level 3 Level 4
Level 1 (Bottom Level)
Shelf
Front Infill
Counter Top
Case Packing

© 2022
Step 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
**
Connection Bar
1
Bolt
Bolt
1
3B
2B
B
B
4B
4A
5B
5A A
A
Velcro on extrusions
must face to BACK of
assembled Backwall.
2A
3A
Velcro on
BACK/Bottom Edges
of Top Horizontals
Velcro on BACK/Top
Edges of Bottom
Horizontals
Velcro on BACK/Inside
Edges of Right Verticals
Velcro on BACK/Inside
Edges of Left Verticals
Horizontal Placement
Stopper
Set upper horizontal extrusion
on top of stopper of verticals.
FRONT VIEW
When Assembled
6B
Steps:
1) Attach base plates [1] lower verticals [2A] and [3A], using bolts.
2) Connect verticals [2A to 2B] and [3A to 3B], using connection bars [B].
See Straight Connection with Knobs detail.
3) Connect horizontals [4A to 4B] and [5A to 5B], using connection bars [A].
See Straight Connection with Knobs detail.
4) Connect assemblies [2A/2B] and [3A/3B] with assemblies [4A/4B] and [5A/5B].
See Corner Connection with Knob detail.
5) Connect extrusions [6A to 2B] and [6B to 3B].
See 2.5”h Angle-Cut Vertical Attachment detail.
6) Attach graphic to Velcro on back of assembled Backwall.
6A
Set Screw
Connector
2.5”h Angle-Cut
Vertical Attachment
Back View of Backwall
Insert connector into groove
of vertical extrusion, then
tighten set screw to secure.
*
Velcro
Slide connection bar between
extrusions, then turn knobs
clockwise to tighten lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
Corner Connection
with Knob
Turn knob clockwise
to tighten lock.
Do not over tighten Knobs
Knob Keep extrusions [6A,6B]
attached to [2B,3B].
Keep A10 clamps
attached to [2A,2B,3A,3B].
Item
1
2A,2B
3A,3B
4A,4B
5A,5B
6A,6B
Description
Base Plate
42” S40 Vertical Extrusion w/ A10 Clamps
42” S40 Vertical Extrusion w/ A10 Clamps
45” Z45 Horizontal Extrusion
45” Z45 Horizontal Extrusion
2.5” S40 Angle-Cut Vertical
Qty.
2
1,1
1,1
1,1
1,1
1,1
Connection bars [A]
stay attached to [4A,5A].
Connection bars [B]
stay attached to [2A,3A].
Backwall Assembly

© 2022
Step 2 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Wing
Wing
3B
3A
2B
2A
Clamp
Wing
Wing
*
*
Literature
Holder
Literature
Holder
Knob
Set Screw
Connector
1) Slide connector of clamp
into extrusion groove.
2) Tighten set screw when
A10 is in desired location.
3) Insert wing into clamp.
4) Tighten knob on clamp
to secure wing in place.
Clamp Attachment
A10 Clamp
Keep A10 clamps
attached to verticals.
*
Connector
Sign Attachment
Cap
Sign
Standoff
Slide connector into groove of extrusion.
Tighten set screws to secure in place.
Screw standoff into connector. Place
sign between standoff and cap then
tighten cap to secure sign.
Connector
Literature Holder
Locks
Literature
Holder
Attach angled end of connector to
literature holder. Attach flat end of
connector to vertical extrusion.
Tighten locks to secure.
*
Keep curved extrusion [10]
& horizontal [11] assembled.
FRONT VIEW
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Clip
Light
Light Connection
Clip
Light
Horizontal Extrusion
Monitor Mount Attachment
Connectors
V4
Connectors
*
Slide V4 Connectors into groove
of Extrusion. Tighten Set Screws
to secure connectors in place.
Attach Monitor Mount back
piece to Extrusion, using bolts.
Then slide monitor mount into
back piece.
Bolts
Monitor
Mount
Back
Piece
Steps:
1) Connect lights to top horizontal extrusions [5A/5B]. See Light Connection detail.
2) Attach assembled Header Frame and affix graphic using Velcro.
3) Attach extrusions [10/11] and shelf to vertical [2A].
4) Attach support leg [10A] to curved extrusion [10].
5) Attach flange plate [11A] to top of curved extrusion [10], using bolt.
6) Attach counter top to counter mounting plate [11A]. See Counter Assembly page.
7) Attach Wings to A10 clamps. See Clamp Attachment detail.
8) Attach Monitor Mount to vertical [2B]. See Monitor Mount Attachment detail.
9) Attach Sign to vertical extrusion [3B]. See Sign Attachment detail.
10) Attach Literature Holders to [3A/3B]. See Literature Holder detail.
Item
7/8/9
10
10A
11
11A
Qty.
1/1/1
1
1
1
1
Description
Header Frame
30.2” Curved Extrusion
Support Leg
12.184” Horizontal Extrusion
Counter Mounting Plate
Keep header
frame assembled,
when packing.
7
8
9
Velcro on extrusions
must face to BACK of
assembled Header.
*
*
Graphic
11A
10
10A
Screw
Shelf
11
*
*
*
Backwall Attachments

© 2022
Step 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
*
Steps
1) Attach horizontals [2] and [2A] between verticals [1], with infills between.
2) Attach curved horizontals [3] between front verticals [1], with infill between.
3) Place shelf on lip of extrusions [2]. See Extrusion Lip detail.
4) Set pedestal top on top of extrusions [2A] and [3].
Infill
Completed Pedestal Assembly
Shelf
Pedestal Top
1
2
2A
3
3
1
11
2
2A
*
Top View
1
2A
3
1
2A
11
Extrusions [2] have
a lip for the shelf
to rest upon.
Lip
Extrusion Lip
*
Pedestal sides [1/1/2/2A]
stay assembled when packing
Infill
I
n
f
i
l
l
Item
1
2,2A
3
Qty
4
2,2
2
Description
38” S40 Vertical Extrusion
12” Z45 Horizontal Extrusion
25” Z45 Horizontal Extrusion
MOD-1243 Pedestal Assembly