SACAGAWEA DESIGNS VK-2108 Manual

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
20’
VK-2108 - 10’ x 20’ Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
REV 12/2022

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2022
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
1) Mounting plate & wing nuts,
in packed position.
6) Place fixed counter bolts
into mounting plate, then
secure using wing nuts.
Completed Assembly
Counter Attachment
Wing Nut
Fixed
Bolts
Mounting
Plate [11A]
10
11
Counter
Attach mounting plate to curved extrusion
[10], using bolt. Insert fixed bolts, located
on underside of counter, into holes of flange
plate. Secure with wing nuts.
Mounting Plate
w/ Wing Nuts
Bottom view
of counter
10
11
Wing Nut
Wing Nut
Counter
2) Mounting plate bolt in,
packed position.
10
11
Bolt
5) Tighten bolt, using hex tool,
to secure.
Mounting Plate
Bolt
3) Place mounting plate onto
[10] then tighten bolt, part
way, allowing some rotation
for final positioning.
4) Place fixed counter bolts
into mounting plate, then lift
counter to re-tighten bolt.
Mounting Plate
10
Fixed
Counter
Bolt
Fixed
Counter
Bolt
Hex Tool
Keep mounting plate [11A] and wing nuts
attached to counter, when packing.
Keep bolt attached to [10], when packing.
Bolt
Mounting
Plate
Bottom view of counter Bottom view of counter
Counter Assembly

© 2022
Case 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Wing Panels
A,A
B,B
6A
3A,3B
2B,2A
6B
4A, 4B, 5A, 5B
Level 2Level 1 (Bottom Level)
Round
Sign
A,A
B,B
6A
3C,3D
2C,2D
6B
4A, 4B, 5A, 5B
Level 3
Base Plates
Graphics
Lights
Setup Hardware
4C 5C
Case Packing

© 2022
Step 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Attach base plates [1] lower verticals [2A] [3A] [2C] and [3C], using bolts.
2) Connect verticals [2A to 2B] [2C to 2D], [3A to 3B] and [3C to 3D], using
connection bars [B]. See Straight Connection with Knobs detail.
3) Connect horizontals [4A to 4B] and [5A to 5B], using connection bars [A].
See Straight Connection with Knobs detail.
4) Attach vertical assemblies [2A/2B] [3A/3B] [2C/2D] and [3C/3D] with horizontal
assemblies [4A/4B] and [5A/5B]. See Corner Connection with Knob detail.
5) Connect extrusions [6A] and [6B] to verticals [2B] [2D] [3B] and [3D].
See 2.5”h Angle-Cut Vertical Attachment detail.
6) Connect left & right assemblies using horizontals [4C,5C].
7) Attach graphic to Velcro on back of assembled Backwall.
Velcro on extrusions
must face to BACK of
assembled Backwall.
Horizontal Placement
Stopper
Set upper horizontal extrusion
on top of stopper of verticals.
Slide connection bar between
extrusions, then turn knobs
clockwise to tighten lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
Corner Connection
with Knob
Turn knob clockwise
to tighten lock.
Do not over tighten Knobs
Knob
Item
1
2A,2B
3A,3B
2C,2D
3C,3D
4A,4B
5A,5B
4C,5C
6A,6B
Description
Base Plate
42” S40 Vertical Extrusion w/ A10 Clamps
42” S40 Vertical Extrusion w/ A10 Clamps
42” S40 Vertical Extrusion
42” S40 Vertical Extrusion
45” Z45 Horizontal Extrusion
45” Z45 Horizontal Extrusion
24” Z45 Horizontal Extrusion
2.5” S40 Angle-Cut Vertical
Qty.
2
1,1
1,1
1,1
1,1
2,2
2,2
1,1
2,2
14A
2A
2B
2C
2D
4B 4C
5A 5B
5C
B
B
Velcro on
BACK/Bottom Edges
Velcro on
BACK/Bottom
Edge
Velcro on
BACK/Top
Edge
Velcro on
BACK/Top Edge
Velcro on
BACK/Inside Edges
of Left Verticals
A
A
FRONT VIEW
Bolt
Bolt
Velcro on
BACK Edges
of Verticals
Velcro on
BACK Edges
of Verticals
**
6B
6A
1
4A
3C
3D
3A
3B
4B
5A 5B
B
B
Velcro on
BACK/Bottom Edges
Velcro on
BACK/Top Edge
A
A
Bolt
Bolt
Velcro on
BACK/Inside Edges
of Right Verticals
**
6B
6A
1
1
Set Screw
Connector
2.5”h Angle-Cut
Vertical Attachment
Back View of Backwall
Insert connector into groove
of vertical extrusion, then
tighten set screw to secure.
*
Velcro
When Assembled
Keep extrusions [6A,6B]
attached to [2B,2D,3B,3D].
Connection bars [A]
stay attached to [4A,5A].
Connection bars [B]
stay attached to [2A,2C,3A,3C].
Keep A10 clamps
attached to [2A,2B,3A,3B].
Backwall Assembly

© 2022
Step 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
1) Slide connector of clamp into
extrusion groove.
2) Tighten set screw when A10 is in
desired location.
3) Insert wing into clamp.
4) Tighten knob on clamp to secure wing
in place.
Clamp Attachment
Connector
Knob
Set Screw
A10
Clamp
Keep A10 clamps
attached to verticals.
*
Connector
Sign Attachment
Cap
Sign
Standoff
Slide connector into groove of
extrusion. Tighten set screws to
secure in place. Screw standoff into
connector. Place sign between
standoff and cap then tighten cap
to secure sign.
FRONT VIEW
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Clip
Light
Light Connection
Clip
Light
Horizontal Extrusion
Steps:
1) Connect lights to top horizontal extrusions. See Light Connection detail.
2) Attach Wings to A10 clamps. See Clamp Attachment detail.
3) Attach Signs to vertical extrusions [2B] & [3B]. See Sign Attachment detail.
Wing
Wing
Wing
Wing
2D
2C
2B
2A
3B
3A
3D
3C
Clamp
*
**
*
Completed Assembly
*
*
Graphic
*
*
Graphic
Backwall Attachments