SadoTech EA-3106 User manual

SadoTtch.f,smT
Thank you for purchasing
manual before using, for
the future.
Reco rdable
Infrared Chime
Model : EA-3106
Sensor Chime. Please read this
Keep this manual for instruction tn
PRODUCT
g lndicator
@ Microphone
@ Power Jack
su ita ble garage, warehouse, hosPital etc.
(No wiriilg, Easy installation)
FUNCTION$
I Record ing Fu nction
Press and hold the record
,uftpress the record button
about 20 seconds.
I Sound $electing Function
Push the three*grade slide switch to:
1). DINGDONG sound
2) ^" Record i ng co nte nt"
3), Alarm sou nd
t Fower On & Off Function
Push the two-grade slide switch to select doorbell's power on and off.
r lndicating Function
The indicator on the doorbell can be used for low voltage indication, power on instruction,
signal reception.
1 ). Low voltage indication: When the supply voltage is lower than 4.0t0.3V, the indicator will
be flashing. That means supply voltage isn't enough and will affect doorbell's normal
operation, please replace the battery in time;
Zi. eo*er on instruction: When the toggle switch connects the power, the indicator will blink,
that means the doorbell is Power on;
button, then talk into the microphone hole what you want to record
after you finished recording. The maximum recording time is
1
?
3
ON
OFF
User Manual
the SadoTech Recordable Motion
proper installation and operation.
ffi ii f': lj'i
ffi lt i'' i1i
t ,....-----.-.-.-. : ! r
<* ---"..--" "....i i
...o;:;d=.i:pr-_
i-"' -.---- -.......1--.'"1 ''1
ffi 1., - Ili*-w
ti#ilii ' .:"'. Ii-l
i;..:ll', l;fi
ffi i;;il:ri iiiii #
l'"'^'" iii
i.-.. i t ;
i.i- 6
O Detector Cover
O Reccrding Button
@ Power Switch
for shop,

3). Signal reception indication: When the doorbell receivessignals, the indicator will be
blinking accordin g to the sound.
r Delaying Function
When the doorbell is power on, it'll work after 10 seconds' delay. When someone enters the
sensing area, it'll respond one of the following sounds: "Ding Dong", "Recording content",
"Alarm"(Customers can preset the sound through the slide switch according to their needs).
r Operation Notes for the Alarm Mode in the Sado Tech
Voice Alert Motion Sensor Doorbell
1).When the motion is activated in Alarm mode and when the alarm is triggered,the alarm will
sound ONLY after a 10-15 seconds delay.This is normal because this will give some time to the
user to leave the room OR turn off the device when they enter the room without sounding the alarm.
2).When the Alarm mode is first turned ON,the user will have about 1 5 seconds to leave the area
before sensing becomes activated.
3).When the Alarm is sounding it will sound for about 30 minutes before self-stopping.
4).To reset the Alarm Mode turn OFF and then ON the power switch.
r Detector Cover
Use the detector cover to narrow the detector area so that it can meet more consumer needs.
CHARGE THE DOORBELL
The doorbell can be powered both by Size-S('t.2V"4pcs) rechargeable battery and adapter.
The adapter will charge it automatically when the battery's power isn't enough. After fully
charged, the adapter will stop charge automatically. lf a battery with capacity 1 .2Y l1500mAH,
after fully charged, the unit can work more than 1 500 hours continuously. lt can also be
powered by common alkaline battery{AA 1.5V"4pcs)
BASIC PARAMETERS
Power: DC GVipowered by DC 6V/300mAh adapter or alkaline batteryAA 1.5V*4pcs, can also
powered by Size-5 rechargeable battery 1.2V*4pcs);
Working current: < 120mA;
Quiescent current: ( 0.8mA;
Volume: >120d8;
Detect distance: 5-8 meters;
Detect angle: 125 degrees;
Working temperature: -20C-+60C.
INSTALLATION DIAGRAM €s
I rolqlul I
Fixed on
the wall
Pull out the battery cCIver, press
the batteries and install them.
To ensure stable power supply, we recommend you to use the adapter(GV 350mA).
NOTES FOR INSTALLATION
1 ). Battery's installation--requires 4pcs AA 1 .5V alkaline battery to ensure best performance;
2). Please flip the switch to "OFF" when replacing with new battery;
3). Select and install the doorbell near to the door, to ensure effective detecting distance;
4). The doorbell can be installed on the table, wall or on the ceiling. lt can also be attached to
the objects with double-sided adhesive tape, preferably with screws;
5). Make the induction angle facing the detecting position, and turn on the power switch;
6). Don't install it under the direct sunlight or damp places, away from the following
environments: strong signal interference and big temperature changes(such as motor or
ventilation openings etc). Outdoor use is prohibited.