Saeco Intelia Deluxe HD8902 User manual

HD8902
HD8900
Register your product and get support at
www.saeco.com/welcome
4219_460_2735_2_DFU-Simple_A5_v1.indd 1 15/12/15 09:53

4219_460_2735_2_DFU-Simple_A5_v1.indd 2 15/12/15 09:53

Intelia/Intelia Deluxe
ENGLISH 4
ČEŠTINA 13
MAGYAR 23
POLSKI 33
SLOVENSKY 43
4219_460_2735_2_DFU-Simple_A5_v1.indd 3 15/12/15 09:53

4
Introduction
Congratulations on buying this Intelia/Intelia Deluxe full automatic espresso machine! To fully benet
from the support that Saeco offers, please register your product at www.saeco.com/welcome.
This quick start guide applies to all Intelia/Intelia Deluxe models with classic milk frother.
For complete instructions download the user manual from www.saeco.com/support.
The machine is suitable for preparing espresso coffee using whole coffee beans.
General description (Fig. 1)
1 Coffee bean hopper lid
2 Coffee bean hopper
3 Power cord socket
4 Water tank
5 Pre-ground coffee compartment
6 Grinder adjustment knob
7 Control panel
8 Coffee grounds container
9 Coffee dispensing spout
10 Drip tray
11 Drip tray cover
12 Drip tray full indicator
13 Espresso button
14 Espresso lungo button
15 Aroma strength button
16 Standby button
17 Menu button
18 Hot water button
19 Steam button
20 Power cord
21 Cleaning brush (for specic types only)
22 Grease for the brew group (for specic types only)
23 Pre-ground coffee measuring spoon
24 Water hardness test strip
25 Coffee residues drawer
26 Brew group
27 Hot water/steam dispensing spout
28 Classic milk frother
Important
Read and follow the safety instructions carefully and only use the
machine as described in this user manual to avoid accidental injury or
damage due to improper use of the machine. Keep this user manual for
future reference.
Warning
- Check if the voltage indicated on the machine corresponds to the
local mains voltage before you connect the machine
- Connect the machine to an earthed wall socket.
- Do not let the power cord hang over the edge of a table or counter,
or touch hot surfaces.
ENGLISH
4219_460_2735_2_DFU-Simple_A5_v1.indd 4 15/12/15 09:53

- Never immerse the machine, mains plug or power cord in water
(danger of electrical shock).
- Do not pour liquids on the power cord connector.
- Never direct the hot water jet towards body parts: danger of burns.
- Do not touch hot surfaces. Use handles and knobs.
- Remove the mains plug from the wall socket:
- If a malfunction occurs.
- If the machine will not be used for a long time.
- Before cleaning the machine.
- Pull on the plug, not on the power cord. Do not touch the mains
plug with wet hands.
- Do not use the machine if the mains plug, the power cord or the
machine itself is damaged.
- Do not make any modications to the machine or its power cord.
Only have repairs carried out by a service centre authorised by
Philips to avoid a hazard.
- This machine can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given
supervision or instruction concerning use of the machine in a safe
way and if they understand the hazards involved.
- Cleaning and user maintenance shall not be made by children unless
they are older than 8 and supervised.
- Keep the appliance and its cord out of reach of children aged less
than 8 years.
- Children shall not play with the appliance.
- Do not spill water on the mains plug.
- Only use the machine as described in the user manual to avoid
potential injury due to misuse.
- Never insert ngers or other objects into the coffee grinder.
- When you descale the machine, always remove the AquaClean lter
from the water tank.Then thoroughly clean the whole water tank
and replace the AquaClean lter.
Caution
- Using 8 AquaClean lters in the correct way ensures that you do not
have to descale the machine for a period of 5000 cups (based on
100 ml cups and 8 lter replacements as indicated by the machine).
- As water is a foodstuff, the water in the water tank must be used up
within 1 to 2 days.
ENGLISH 5
4219_460_2735_2_DFU-Simple_A5_v1.indd 5 15/12/15 09:53

- If you are not going to use your coffee machine for a prolonged
period (e.g. a holiday), we recommend that you discard any water left
inside the tank and leave the AquaClean lter inside. Before you use
the coffee machine again, take out the Aquaclean lter, clean the
water tank and perform a manual rinsing cycle.Then prepare the
AquaClean lter.
- Do not put any of the detachable parts of the machine in the
dishwasher, except for the milk carafe.
- The machine is for household use only. It is not intended for use in
environments such as canteens, staff kitchen of shops, ofces, farms
or other work environments.
- Always put the machine on a at and stable surface.
- Do not place the machine on hot surfaces, directly next to a hot
oven, heater or similar source of heat.
- Only put roasted coffee beans into the coffee bean hopper. If ground
coffee, instant coffee, raw coffee beans or any other substance is put
in the coffee bean hopper, it may damage the machine.
- Let the machine cool down before inserting or removing any parts.
- Never use warm or hot water to ll the water tank. Use cold non-
sparkling drinking water.
- Never clean with scrubbing powders or harsh cleaners. Simply use a
soft cloth dampened with water.
- Descale the machine regularly.The machine indicates when descaling
is needed. If you do not clean and descale the machine, you run the
risk that the machine stops working and that your guarantee
becomes invalid.
- Do not keep the machine at temperatures below 0°C.Water left in
the heating system may freeze and cause damage.
- Do not leave water in the tank when the machine is not used over a
long period of time.
The water can be contaminated. Use fresh water every time you use
the machine.
Electromagnetic elds (EMF)
This machine complies with all applicable standards and regulations regarding exposure to
electromagnetic elds.
ENGLISH6
4219_460_2735_2_DFU-Simple_A5_v1.indd 6 15/12/15 09:53

The display
Some buttons can be used to navigate through the menus:
- ESPRESSO button = ESC button: you can press this button to return to the main menu.
The ESC button takes you back one level.You may have to press the ESC button. several times
to get back to the main menu (Fig. 2).
- AROMA STRENGTH button = OK button: you can press this button to select, conrm or stop
a function (Fig. 3).
- STEAM button = UP button: press this button to scroll up through the display menu. (Fig. 4)
- MENU button = DOWN button: press this button to scroll down through the display
menu (Fig. 5).
First installation
1 Slide the drip tray with drip tray cover into the machine.
2 Remove the water tank.
3 Fill the water tank to the MAX level with fresh water.
4 Fill the coffee bean hopper with coffee beans.
5 Insert the small plug into the socket located on the back of the machine. Insert the mains
plug into the wall socket.
6 Attach the classic milk frother to the hot water/steam dispensing spout
7 Place a container under the classic milk frother.
8 Press the STANDBY button to switch on the machine.
9 Press the OK button to start the automatic circuit priming cycle.
10 The displays shows the following icon to indicate that the machine is heating up (Fig. 6).
,The machine performs an automatic rinsing cycle (Fig. 7).
11 ThedisplayshowsthefollowingicontoindicateyouhavetoinstalltheAquaCleanlter
(Fig. 8).
Note: If you want to install the AquaClean lter later, press the ESC button and continue with the manual
rinsing cycle. For installation see chapter ‘AquaClean lter’.
12 Press the OK button, the display shows the following icon (Fig. 9).
13 RemovetheAquaCleanlterfromitspackaging.Shakethelterforabout5seconds.
14 Immersethelterupsidedowninajugwithcoldwaterandwaituntilnomoreairbubbles
come out (Fig. 10).
15 Removethewatertankfromthemachine,emptyitandinsertthelterverticallyontothe
lterconnection(Fig.11).
16 Fill the water tank with fresh water and slide it back into the machine.
17 Press the OK button.
18 SelectONonthedisplayandconrmtheactivationbypressingtheOKbutton(Fig.12).
Note: The display shows a tick icon to conrm the activation (Fig. 13).
19 ThedisplayshowsthelterreadyicontoindicatetheAquaCleanlterhasbeeninstalled
correctly (Fig. 14).
ENGLISH 7
4219_460_2735_2_DFU-Simple_A5_v1.indd 7 15/12/15 09:53

20 Torinsethelter,presstheHOTWATERbuttonandlethalfalitreofwaterowoutfrom
the hot water/steam dispensing spout. Discard this water.
The machine is ready for use.
Note: After installing the AquaClean lter you do not have to perform the manual rinsing cycle.
Manual rinsing cycle
1 Place a container under the hot water/steam dispensing spout.
2 PresstheAROMASTRENGTHbuttontoselectpre-groundcoffee.
Donotaddpre-groundcoffee.
3 PresstheESPRESSOorESPRESSOLUNGObutton.Themachinestartsdispensingwater.
4 Whenthemachinestopsdispensing,emptythecontainer.Repeatsteps1-3twice.
5 Place a container under the classic milk frother.
6 PresstheHOTWATERbutton.Hotwaterdispensingstartsautomatically.
,Dispense water until the display shows no water icon.
7 Fill the water tank with fresh water up to the MAX level and remove the container.
The machine is ready for use.
AquaClean lter
The AquaClean lter is designed to reduce limescale deposits in your coffee machine and provide
ltered water to preserve the aroma and avour of each cup of coffee. Using 8 AquaClean lters
correctly allows you to descale your machine every 2 years only, or every 5000 cups (with 100 ml
capacity)
AquaClean lter installation
Note: Your machine has to be completely limescale-free before you start to use the AquaClean lter.
If you did not activate the lter upon rst use and brewed more than 50 cups (with 100 ml capacity),
you need to descale the machine before you activate the lter.
1 RemovetheAquaCleanlterfromitspackaging.Shakethelterforabout5seconds.
2 Immersethelterupsidedowninajugwithcoldwaterandwaituntilnomoreairbubbles
come out. (Fig. 10)
3 Removethewatertankfromthemachineandinsertthelterverticallyontothelter
connection. (Fig. 11)
4 Fill the water tank with fresh water and slide it back into the machine.
5 PresstheMENUbuttonandscrollthemenutotheAquaCleanlteroption.
ThenpresstheOKbuttontoselecttheAquaCleanlteroption.
Note: If you are installing the lter at rst time use, follow the steps in chapter ‘First installation’.
6 SelectONonthedisplayandconrmtheactivationbypressingtheOKbutton.
Note: The display shows a tick icon to conrm the activation.
7 Torinsethelter,presstheHOTWATERbuttonandlethalfalitreofwaterowoutfrom
the hot water/steam dispensing spout. Discard this water.
Note: It can take a while until water comes out of the dispensing spout. The lter needs to be fully lled
and rinsed with water
ENGLISH8
4219_460_2735_2_DFU-Simple_A5_v1.indd 8 15/12/15 09:53

8 UsethestickerattachedtotheplasticpackagingoftheAquaCleanltertowritedownthe
dateofthenextlterreplacement(after3months).Placethestickeronthewatertank.
,Thelterandmachinearenowreadyforuse.
Replacing the AquaClean lter
Replace the lter every 3 months or at machine request.
Display icon AquaClean
lter Whattodo
10% + icon ashes The performance of this lter is decreasing. It is recommended to
remove the old lter and place the new lter as described in section
‘AquaClean lter installation’ to retain proper lter performance.
0% + icon ashes Remove the old lter immediately and place the new lter as
described in section ‘AquaClean lter installation’.
0% and icon disappears
from display
You rst need to descale the machine before you can place and
activate a new lter.
After 8 lter replacements you need to descale the machine see chapter ‘Descaling’, section
‘Descaling procedure’.
Using the machine
Brewing coffee with beans
1 Adjustthecoffeedispensingspouttosuitthesizeofyourcup.
2 PresstheAROMASTRENGTHbuttontoselectthedesiredstrengthfrom1-5beans.
3 PresstheESPRESSObuttontobrewanespressoorpresstheESPRESSOLUNGObuttonto
brew a coffee.
Adjusting the coffee quantity
1 PressandholdtheESPRESSObuttonorESPRESSOLUNGObuttonuntilthedisplayshows
thewordMEMO.
2 Whenthecupcontainsthedesiredamountofcoffee,presstheOKbuttontosavethe
selected quantity.
Adjusting the grind setting
Note: Only adjust the grind setting while the grinder is working.
1 Open the bean hopper.
2 PlaceacupunderthecoffeedispensingspoutandpresstheESPRESSObuttontobrewan
espresso.
3 Whilethemachinegrindsthecoffee,placetheendofthemeasuringspoonhandleonthe
grinderadjustmentknobinthecoffeebeanhopper.Usethespoontopressandturnthe
knob to the left or to the right one notch a time.
4 There are 10 different grinding degree settings you can choose from.The smaller the dot,
the stronger the coffee.
1 Coarse grind: lighter taste, for dark roasted coffee blends.
2 Fine grind: bolder taste, for light roasted coffee blends.
5 Brew2-3coffeestotastethedifference.
ENGLISH 9
4219_460_2735_2_DFU-Simple_A5_v1.indd 9 15/12/15 09:53

Frothing milk
Dangerofscalding.Dispensingmaybeprecededbysmalljetsofhotwater.Onlyusethe
appropriate protective handle.
1 Fill1/3ofajugwithcoldmilk.
2 Immersetheclassicmilkfrotherinmilk.PresstheSTEAMbutton.
3 Froththemilkbygentlyswirlingthejugandmovingitupanddown.
4 Press the OK button to stop frothing.
Hot water
Dangerofscalding.Dispensingmaybeprecededbysmalljetsofhotwater.Onlyusethe
appropriate protective handle.
1 Placeajugundertheclassicmilkfrother.
2 PresstheHOTWATERbutton.Hotwaterdispensingstartsautomatically.
3 Press the OK button to stop hot water dispensing. Remove the container.
Descaling
You have to descale the machine when the display shows the CALC CLEAN icon or after
8 AquaClean lter replacements.
Note: If you do not descale when the display shows the CALC CLEAN icon or after 8 AquaClean lter
replacements, the machine may stop working properly. In this case, repairs are not covered by the
guarantee. (Fig. 15)
Never drink the water with descaling mixture that you pour into the water tank or any water
with residues that comes out of the machine during the descaling procedure.
The descaling procedure lasts approximately 30 minutes. Only use the Saeco descaling solution to
descale the machine.The Saeco descaling solution is designed to ensure optimal performance of the
machine.You can buy the Saeco descaling solution in the online shop at www.shop.philips.com/
service.
Descaling procedure
Note: You can pause the descaling or rinsing cycle by pressing the ESC button. The display will show the
following icon. To continue the descaling or rinsing cycle, press the OK button (Fig. 16).
1 Remove and empty the drip tray. Slide the drip tray back into the machine.
Note: Remove the AquaClean water lter from the water tank (if present).
2 Remove the classic milk frother from the steam wand.
3 Press the OK button.
4 The display shows the following icon to indicate that the machine enters the descaling cycle.
Ifyouwanttoexitthedescalingcycle,presstheESCbutton.(Fig.17)
5 Pour the entire bottle of Saeco descaling solution (250ml) into the water tank.
6 AddwatertothedescalingsolutioninthewatertankuptotheCALCCLEANindication.
7 Place a large container (1.5 l) under the steam wand and dispensing spout.
ENGLISH10
4219_460_2735_2_DFU-Simple_A5_v1.indd 10 15/12/15 09:53