Saeco Moltio HD8766 User manual

English
USER MANUAL
Read carefully before using the machine.
Register your product and get support at
www.saeco.com/welcome
Type HD8766 - HD8767
EN
02
02

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse
cord, plugs, or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near
children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair
or adjustment.
7. The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10.Do not place on or near a hot gas or electric burner, or in a heated oven.
11.Always attach plug to appliance first, then plug cord into wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
12.Do not use appliance for other than intended use.
13.Save these instructions.
SAVE THESE INSTRUCTIONS

CAUTION
This appliance is for household use only. Any servicing, other than cleaning
and user maintenance, should be performed by an authorized service center.
Do not immerse machine in water. To reduce the risk of fire or electric shock,
do not disassemble the machine. There are no parts inside the machine
serviceable by the user. Repair should be done by authorized service personnel
only.
1. Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2. Never use warm or hot water to fill the water tank. Use cold water only.
3. Keep your hands and the cord away from hot parts of the appliance during
operation.
4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5. For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6. Do not use caramelized or flavored coffee beans.
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A. A short power-supply cord (or detachable power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
B. Longer detachable power-supply cords or extension cords are available
and may used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used,
1. The marked electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance
2. If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or tripped
over.

2 ENGLISH
Congratulations on your purchase of a Saeco Moltio Classic
Milk Frother fully automatic coee machine!
To fully benet from the support that Saeco oers, please
register your product at www.saeco.com/welcome.
The machine is made for preparing espresso coee using
whole coee beans and for dispensing steam and hot water.
In this user manual you will nd all the information you need
to install, use, clean and descale your machine.

3 ENGLISH
CONTENTS
INSTALLATION ................................................................................................. 4
Product Overview ................................................................................................................................4
General Description .............................................................................................................................5
PREPARING FOR USE........................................................................................ 6
Machine Packaging..............................................................................................................................6
Machine Installation............................................................................................................................6
USING THE MACHINE FOR THE FIRST TIME ........................................................10
Circuit Priming...................................................................................................................................10
Automatic Rinse/Self-Cleaning Cycle.................................................................................................11
Manual Rinse Cycle............................................................................................................................11
Measuring and Programming Water Hardness ..................................................................................14
“INTENZA+”Water Filter Installation.................................................................................................15
Replacing the“INTENZA+”Water Filter..............................................................................................17
CHANGING COFFEE BEANS ...............................................................................18
Removing the Coee Bean Hopper ....................................................................................................18
Inserting the Coee Bean Hopper......................................................................................................19
Selecting Coee Beans ......................................................................................................................21
Coee Emptying Cycle .......................................................................................................................22
ADJUSTMENTS................................................................................................23
Saeco Adapting System .....................................................................................................................23
Adjusting the Ceramic Coee Grinder ...............................................................................................23
Adjusting the Aroma (Coee Strength)..............................................................................................24
Adjusting the Coee Dispensing Spout..............................................................................................25
Adjusting the Coee Length .............................................................................................................26
BREWING ESPRESSO AND COFFEE ....................................................................27
Brewing Espresso and Coee Using Coee Beans ..............................................................................27
Brewing Espresso and Coee Using Pre-Ground Coee......................................................................28
DISPENSING STEAM / BREWING CAPPUCCINO...................................................29
Frothing Milk.....................................................................................................................................29
Brewing a Cappuccino .......................................................................................................................30
DISPENSING HOT WATER .................................................................................31
CLEANING AND MAINTENANCE ........................................................................32
Daily Cleaning of the Machine ...........................................................................................................32
Daily Cleaning of the Water Tank........................................................................................................34
Daily Cleaning of the Classic Milk Frother...........................................................................................34
Weekly Cleaning of the Machine........................................................................................................34
Weekly Cleaning of the Classic Milk Frother.......................................................................................35
Weekly Cleaning of the Brew Group...................................................................................................35
Weekly Cleaning of the Coee Bean Hopper, Tray and Coee Compartment......................................39
Monthly Lubrication of the Brew Group.............................................................................................40
DESCALING.....................................................................................................42
ACCIDENTAL INTERRUPTION OF THE DESCALING CYCLE .....................................47
PROGRAMMING..............................................................................................49
The following settings can be adjusted..............................................................................................49
How to Program the Machine............................................................................................................50
MEANING OF THE DISPLAY ICONS.....................................................................52
TROUBLESHOOTING........................................................................................56
ENERGY SAVING..............................................................................................59
Stand-by............................................................................................................................................59
TECHNICAL SPECIFICATIONS............................................................................60
WARRANTY AND SERVICE ................................................................................60
Warranty ...........................................................................................................................................60
Service...............................................................................................................................................60
ORDERING MAINTENANCE PRODUCTS ..............................................................61
MACHINE ACCESSORIES...................................................................................62

4
INSTALLATION
Product Overview
17
21
22
19
23
20
32
18
12
3
11 12 13 14
5
4c
4b
4a
6
7
8
9
24
26
27
29
25 28
16
15
10
30 31

5 ENGLISH 5
General Description
1. Coee bean hopper locking/removal selector switch
2. Pre-ground coee compartment
3. Cup stacking surface
4a. Coee bean hopper
4b. Coee bean hopper tray
4c. Coee bean hopper lid
5. Control panel
6. Coee dispensing spout
7. Cup holder grill
8. Full drip tray indicator
9. Drip tray
10. Classic Milk Frother (for hot water/steam)
11. Coee grounds drawer
12. Brew group
13. Coee residues drawer
14. Service door
15. Wand protective gripper
16. Water tank
17. Power cord socket
18. Power button
19. Coee grinder adjustment key + Pre-ground coee measuring scoop
20. Cleaning brush (optional)
21. Grease for brew group (optional)
22. Power cord
23. Water hardness test strip
24. Espresso brew button
25. Coee brew button
26. Steam / hot water button
27. "Aroma" - Pre-ground coee button
28. "MENU" button
29. ON/OFF button
30. Descaling solution (to be purchased separately)
31. Filter (INTENZA+) (to be purchased separately)
32. Protection lid (optional)

6 ENGLISH
PREPARING FOR USE
Machine Packaging
The original packaging has been designed and constructed to protect the
machine during transport. We recommend keeping the packaging material
for possible future transport.
Machine Installation
1Remove the drip tray with grill from the packaging.
2Remove the machine from the packaging.
3For best use, it is recommended to:
• Choose a safe, level surface, where there will be no danger of over-
turning the appliance or being injured;
• Choose a location that is suciently well-lit, clean and near an eas-
ily reachable socket.
• Allow for a minimum distance from the sides of the machine as
shown in the gure.
4Insert the drip tray with grill into the machine. Make sure it is fully
inserted.
Note:
The drip tray collects the water that comes out of the coee dispensing
spout during each rinse/self-cleaning cycle, as well as any coee that
might be spilled during beverage brewing. Empty and wash the drip tray
daily and each time the full drip tray indicator is raised.
Caution:
NEVER remove the drip tray when the machine has just been turned
on. Wait a couple of minutes for the machine to carry out a rinse/self-
cleaning cycle.

7 ENGLISH 7
5Press gently on the side of the water tank door to release the handgrip.
7Rinse the water tank with fresh water.
8Fill the water tank with fresh water up to the MAX level and reinsert it
into the machine. Make sure it is fully inserted.
Caution:
Never ll the water tank with warm, hot, sparkling water or any other
liquid, as this may cause damage to the water tank and the machine.
6Remove the water tank by pulling it by the handgrip.
Note:
When the water tank is full, it must be transported as shown in the gure.

8 ENGLISH
13 Switch the power button to "I". The red light next to the " " button
ashes.
11 Insert the plug into the socket located on the back of the machine.
12 Insert the plug at the other end of the power cord into a wall socket
with suitable power voltage.
1
2
9Remove the coee bean hopper lid. Slowly pour in the coee beans.
Note:
The coee bean hopper contains a tray that vibrates during grinding and
conveys the beans into the coee grinder.
Caution:
Only coee beans must be put into the coee bean hopper. If ground
coee, instant coee, avored coee, raw coee beans or any other
substance is put in the coee bean hopper, it may damage the ma-
chine.
10 Put the lid back on the coee bean hopper.

9 ENGLISH 9
14 To turn on the machine, simply press the “ ” button.
Yellow
Note:
By keeping the button pressed for more than 8 seconds, the machine
enters the demo mode. To exit the demo, turn the machine o and on
again using the power button.
15 The control panel indicates that the circuit must be primed.

10 ENGLISH
USING THE MACHINE FOR THE FIRST TIME
When using the machine for the rst time, the following activities need to
happen:
1) You need to prime the circuit;
2) The machine will perform an automatic rinse/self-cleaning cycle.
3) you need to perform a manual rinse cycle.
Circuit Priming
During this process, fresh water ows through the internal circuit of the
machine and the machine warms up. This takes a few minutes.
1Place a container under the Classic Milk Frother.
2Press the “ ” button to start the cycle. The machine starts the auto-
matic priming of the circuit by dispensing some water through the
Classic Milk Frother.
Yellow
3The bar under the icon shows the operation progress. When the pro-
cess has been completed, the machine stops dispensing automatically.
4The control panel now shows the machine warm-up icon.
Yellow

11 ENGLISH 11
Automatic Rinse/Self-Cleaning Cycle
When warm-up has been completed, the machine automatically performs
a rinse/self-cleaning cycle of the internal circuits with fresh water. This
takes less than a minute.
1Place a container under the coee dispensing spout to catch the small
amount of water which will be dispensed.
2The machine shows this display. Wait for the cycle to nish automati-
cally.
Note:
You can stop dispensing by pressing the “ ” button.
Yellow
Green
3When the operations described above have been completed, the ma-
chine shows this display. You can now perform the manual rinse cycle.
Manual Rinse Cycle
During this process you activate the coee brewing cycle and fresh water
ows through the water circuit. This takes a few minutes.
1Place a container under the coee dispensing spout.

12 ENGLISH
2Check that the machine shows this display.
Green
3Select the pre-ground coee brewing function by pressing the “ ”
button. The machine shows this display.
Note:
Do not add any pre-ground coee into the compartment.
4Press the “ ” button. The machine starts dispensing water.
5When dispensing has nished, empty the container. Repeat the opera-
tions from step 1 to step 4 twice, then continue with step 6.
6Place a container under the Classic Milk Frother.
Green
7Press the “ ” button. The machine shows this display.
Green
8Press the “ ” MENU button to start dispensing hot water.

13 ENGLISH 13
Red
9After dispensing water, remove and empty the container.
11 At the end of this operation, ll the water tank again up to the MAX
level. Now the machine is ready to brew coee.
This icon will be displayed.
Note:
The automatic rinse/self-cleaning cycle starts when the machine has been
in stand-by mode, or turned o, for more than 15 minutes.
When you have not used the machine for 2 or more weeks, you will also
need to perform a manual rinse cycle.
At the end of the cycle, you can brew a coee.
Green
10 Repeat steps 7 to 9 until the water tank is empty and the no water
warning sign appears.
Note:
Press the “ ” button to stop the manual rinse cycle.

14 ENGLISH
Measuring and Programming Water Hardness
Water hardness measuring is very important in order to dene the descal-
ing frequency and to install the “INTENZA+” water lter (for more details on
the water lter, see next chapter).
To measure the water hardness follow the steps below:
1Immerse the water hardness test strip (supplied with the machine) in
water for 1 second.
Note:
The test strip can only be used for one single measurement.
2Wait for one minute.
23 4
ABC
Intenza Aroma System
Machine Water Hardness Setting
1
3Check how many squares have changed to red, then consult the table.
Note:
The numbers on the water hardness test strip correspond to the water
hardness adjustment settings.
More precisely:
1 = 1 (very soft water)
2 = 2 (soft water)
3 = 3 (hard water)
4 = 4 (very hard water)
The letters correspond to the references that are located at the base of the
“INTENZA+” water lter (see next chapter).
4Press the “ ” MENU button and scroll through the options by pressing
the “ ” MENU button until this icon is displayed.
Note:
The machine is supplied with a standard water hardness setting, suitable
for most types of water.
Yellow Green

15 ENGLISH 15
7Press the “ ”button to exit the programming menu. The machine is
now ready for brewing.
“INTENZA+”Water Filter Installation
We recommend that you install the “INTENZA+” water lter as this prevents
limescale build-up in your machine and preserves a more intense aroma of
your coee.
The “INTENZA+” water lter can be purchased separately. For further de-
tails, please refer to the maintenance products page in this user manual.
Water is a crucial part of every coee, so it is very important to always have
it professionally ltered. Using the“INTENZA+” water lter will prevent
mineral deposits from building up and improve your water quality.
1Remove the small white lter from the water tank and store it in a dry
place.
Green Yellow
5Press the ““ ” button to increase the value and the“ ” button to
decrease the value.
6Press the “ ” MENU button to conrm the setting.

16 ENGLISH
2Remove the “INTENZA+” water lter from its packaging, immerse it ver-
tically (with the opening positioned upwards) in cold water and gently
press the sides so as to let the air bubbles out.
3Set the “INTENZA+” water lter according to the measurements per-
formed (see previous chapter) and indicated on the base of the lter:
A = soft water – equals 1 or 2 on the test strip
B = hard water (standard) – equals 3 on the test strip
C = very hard water – equals 4 on the test strip
4Put the "INTENZA +" water lter into the empty water tank. Press it
down until it cannot move any further.
5Fill the water tank with fresh water and put it into the machine.
6Dispense all the water in the tank by using the hot water function (see
the “Dispensing Hot Water” section).
7Fill the water tank again.
8Press the “ ” MENU button and scroll through the options by pressing
the “ ” MENU button until this icon is displayed.
GreenYellow

17 ENGLISH 17
9Press the “ ” button to select “ON”and press the “ ” MENU button to
conrm.
Yellow
Replacing the “INTENZA+”Water Filter
When the “INTENZA+” water lter needs to be replaced with a new one,
this icon is displayed.
1Replace the “INTENZA+” water lter as described in the previous chap-
ter.
Yellow
10 To exit, press the“ ”button. The machine is now ready for brewing.
In this way the machine has been programmed to inform the user of
the need to replace the“INTENZA+” water lter.
GreenYellowYellow
3Select the “RESET” option. Press the " " button to conrm.
2Press the “ ” MENU button and scroll through the options by pressing
the “ ” MENU button until this icon is displayed.

18 ENGLISH
Yellow Green
4To exit, press the“ ”button. The machine is now ready for brewing.
The machine is now programmed to manage a new lter.
Note:
If the “INTENZA+” water lter is already installed and you want to remove,
but not replace it, select the “OFF”option instead.
If there is no “INTENZA+” water lter installed, insert the small white lter
previously removed into the water tank.
CHANGING COFFEE BEANS
The machine comes with a removable coee bean hopper so you can
easily switch from one type of coee bean to another and enjoy a dierent
coee taste.
Note:
You can buy an additional coee bean hopper as an accessory (CA6803).
To preserve their taste, you can store coee beans in the bean hopper in
the refrigerator.
Removing the Coee Bean Hopper
To remove the coee bean hopper follow the steps below:
1Move the selector switch to the“ ” position.
Caution:
It may happen that the selector switch can not be shifted as it is
blocked by coee beans. In this case, move the selector switch back
and forth until the coee beans are released.