Saeco Primea Ring User manual

Operation and maintenance manual
Before using the machine, please read the attached operating instructions.
Carefully read the safety rules
FOR HOUSEHOLD USE ONLY

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse
cord, plugs, or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near
children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair or
adjustment.
7. The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10.Do not place on or near a hot gas or electric burner, or in a heated oven.
11.Always attach plug to appliance first, then plug cord into wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
12.Do not use appliance for other than intended use.
13.Save these instructions.
SAVE THESE INSTRUCTIONS

CAUTION
This appliance is for household use only. Any servicing, other than cleaning and
user maintenance, should be performed by an authorized service centre. Do
not immerse machine in water. To reduce the risk of fire or electric shock, do not
disassemble the machine. There are no parts inside the machine serviceable
by the user. Repair should be done by authorized service personnel only.
1Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2Never use warm or hot water to fill the water tank. Use cold water only.
3Keep your hands and the cord away from hot parts of the appliance during
operation.
4Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6 Do not use caramelized coffee
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A. A short power-supply cord (or detachable power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
B. Longer detachable power-supply cords or extension cords are available and
may used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used,
1. The marker electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance
2. If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the counter
top or table top where it can be pulled on by children or tripped over.

2 INDEX
WARNING ......................................................................................................................................2
APPLIANCE ....................................................................................................................................4
ACCESSORIES .................................................................................................................................................4
INSTALLATION ...............................................................................................................................5
STARTING THE MACHINE .....................................................................................................................................5
SETTING THE LANGUAGE .....................................................................................................................................6
INTENZA WATER FILTER ......................................................................................................................................7
DISPLAY ........................................................................................................................................8
COFFEE AROMA...............................................................................................................................................8
ADJUSTMENTS ..............................................................................................................................9
COFFEE INTENSITIY ...........................................................................................................................................9
ADJUSTING THE HEIGHT OF THE DRIP TRAY ................................................................................................................9
FILLING THE MILK CONTAINER ...............................................................................................................................9
BEVERAGE DISPENSING................................................................................................................10
ESPRESSO / COFFEE / LONG COFFEE.....................................................................................................................10
DISPENSING BEVERAGES WITH GROUND COFFEE .........................................................................................................11
LATTE MACCHIATO .........................................................................................................................................12
ESPRESSO MACCHIATO.....................................................................................................................................14
CAPPUCCINO ................................................................................................................................................14
DISPENSING HOT MILK .....................................................................................................................................15
HOT WATER DISPENSING ...................................................................................................................................15
BEVERAGE PROGRAMMING...........................................................................................................16
1. PROGRAMMING FOR SELF-INSTRUCTING ..............................................................................................................16
2. PROGRAMMING FROM THE “BEVERAGE SETTINGS” MENU ...........................................................................................16
PROGRAMMING THE MACHINE......................................................................................................18
MACHINE SETTINGS ........................................................................................................................................19
LANGUAGE MENU.....................................................................................................................................19
CUP WARMER MENU .................................................................................................................................20
WATER FILTER MENU ................................................................................................................................20
RINSE MENU..........................................................................................................................................21
WATER HARDNESS MENU - INTENZA AROMA SYSTEM ............................................................................................21
ACOUSTIC ALARM MENU.............................................................................................................................22
MAINTENANCE MENU ......................................................................................................................................23
MILK CIRCUIT RINSE CYCLE..........................................................................................................................23
COFFEE WASH CYCLE ................................................................................................................................24
MILK WASH CYCLE ...................................................................................................................................25
DESCALING CYCLE....................................................................................................................................28
CLOCK SETTINGS ...........................................................................................................................................30
TIME SETTING ........................................................................................................................................30
DATE SETTING........................................................................................................................................31
TIME FORMAT ........................................................................................................................................31
STANDBY SETTING..........................................................................................................................................32
ENERGY SAVING ......................................................................................................................................32
TIMER SETTING.......................................................................................................................................32
SPECIAL FUNCTIONS........................................................................................................................................34
DELETING ALL THE SETTINGS .......................................................................................................................34
COFFEE IN THE WORLD ..............................................................................................................................35
BEVERAGE COUNTERS................................................................................................................................36
CLEANING AND MAINTENANCE .....................................................................................................37
MAINTENANCE DURING OPERATION........................................................................................................................37
GENERAL MACHINE CLEANING .............................................................................................................................37
MILK CONTAINER MAINTENANCE AND CLEANING .........................................................................................................38
CLEANING THE BREW GROUP. .............................................................................................................................40
GRINDER MAINTENANCE....................................................................................................................................41
ERROR CODES.............................................................................................................................42
SAFETY RULES ............................................................................................................................43
TECHNICAL DATA .........................................................................................................................45

3
The coffee machine is intended for preparing espresso by using either coffee beans or ground coffee. It
includes an automatic device for preparing milk beverages and a hot water dispenser.
The machine is elegantly designed for domestic use and is not suitable for continuous heavy duty or
professional use.
Warning: no liability is assumed for any damage caused by:
• Incorrect use not in accordance with the intended uses;
• Repairs not carried out by authorized customer service centers;
• Tampering with the power cord;
• Tampering with any part of the machine;
• The use of non-original spare parts and accessories;
• Failure to descale the machine or use at temperatures below 0°C.
IN THESE CASES, THE WARRANTY IS NOT VALID.
Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee
machine. For further information or if you experience problems not completely or sufficiently addressed in these
instructions, please contact an Authorized Customer Service Center.
KEEP THESE INSTRUCTIONS
A WARNING TRIANGLE DRAWS ATTENTION TO ALL THE INSTRUCTIONS THAT
ARE IMPORTANT FOR USER SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS
CAREFULLY TO AVOID SERIOUS INJURY!
HOW TO USE THESE OPERATING INSTRUCTIONS
GENERAL INFORMATION

4
Cappuccinatore
maintenance kit
Cit
Ground coffee
measuring scoop
Cleaning detergent
(Brew group)
Water hardness
tester
Grinder
adjustment key
Lubricant for the
brew group
Detergent for cleaning
milk container
i
d
t
Intenza water filter
ACCESSORIES
Control panel
SBS
APPLIANCE
Compartment for pre-
ground coffee
Brew group
Coffee grounds drawer
Socket for
power cord
Open coffee bean hopper
button
Coffee bean hopper
Cup warming plate
Main switch
Service door
Coffee bean hopper cover
Drip tray
Button for raising/lowering
the drip tray
Dispensing head
Drip tray + grill and float
Compartment for
milk container
Hot water spout
Water tank
Milk compartment
button

5
1 2 3
4
7
65
INSTALLATION
Attach the female end of the
power cord to the machine. Insert
the male end into the power
outlet.
Place a container beneath the hot
water spout.
Press the button on the coffee
hopper to open the cover. Fill the
hopper with coffee beans.
Close the cover pushing it down
completely.
Remove the water tank.
We recommend installing the
water filter (see page 7).
Press the main switch to the “On”
position.
Make sure that the main power button is not switched to the “ON” position.
Fill the tank with fresh drinking
water. Do not exceed the “max”
level indicated on the water tank.
Once filled place the tank back
into the machine.
STARTING THE MACHINE
BEFORE PERFORMING ANY OPERATION, COMPLETE
THE INSTALLATION (PAGES 6 – 7).
TO ADJUST THE WATER HARDNESS LEVEL AND SET
THE INTENZA AROMA SYSTEM SEE THE «WATER
HARDNESS MENU» ON PAGE 21.

6
6
press ok
boiler filling
Press to prime the circuit; wait until
the machine stops.
7
warming up
please wait
8
rinsing
please wait
9
strong aroma
espresso coffee 08:33
When the priming is completed,
wait until the machine has
finished the heating phase.
Once the heating phase is
completed, a small quantity of
water is dispensed. Wait for this
cycle to be completed
automatically. Refer to page 21 to
enable/disable the function.
The screen for product dispensing
appears on the display.
INSTALLATION
1 2 3
5
SETTING THE LANGUAGE
When the machine is switched-on for the first time, it requires the selection of the desired language.
This allows you to adjust the parameters of the beverages to the typical parameters of the country
where the machine is used. This is why some languages are differentiated also by country.
english
language
Select the language by navigating
the click wheel with your finger.
When the desired language is
displayed, press .
The machine now displays the
messages in the selected
language.
The machine displays the
following menu.
Wait before making the
selection.
In this phase you must decide
whether to install the water filter.
Its use is recommended by
Saeco. The water filter purifies
water and allows you to taste the
full aroma of coffee.
Otherwise, select and press .
If you want to install the water
filter, go to page 7.
2.
1.
4
english
language
water filter inserted
yes
water filter inserted
no

7
56
78 9
4
13 2
Remove the small white filter
from the tank and store it in a dry
place sheltered from dust.
Fill the tank with fresh drinking
water and reinsert it into the
machine.
Set the Intenza Aroma System:
A = Light water
B = Medium water (standard)
C = Hard water
For further details see page 21
INTENZA WATER FILTER
To improve the quality of the water you use, and extend the life of your machine at the same time, it is
recommended that you install the water filter. After installation, go to the water filter initialization program
(see programming). In this way, the machine informs the user when the water filter must be replaced.
Remove the water filter from its packaging, immerse it vertically (with the opening facing upwards)
in cold water and gently press its sides so as to let the air bubbles out.
Insert the filter in its place within
the empty tank (see figure);
Press down until it clicks into
place.
The machine initialises the filter.
Then, press repeatedly. When the “exit” message is displayed, press . In this way, the machine ends
the start-up phase. Wait until at the end of the procedure, the display shows what is shown on page 8.
NOTE: if the Intenza water filter is not available, insert the small white filter previously removed (see point 1)
into the tank.
Place a container under the
spout. Press .
water filter inserted
yes
push ok
initialisation
in progress
initialisation
Press again.
done
initialisation
Press again.

8
• Press the key twice to make 2 cups. This operation can be performed until the grinding is
complete.
Press twice
By pressing the key, there are three
possible selections (strong, medium, mild) that
indicate the aroma (coffee quantity to be ground
by the machine) for the beverage selected. This
key enables you to select also the ground coffee
function.
DISPLAY
Enter the
programming menu
COFFEE AROMA
strong aroma
espresso coffee 08:33
Select dispensing of
beverages with milk
Confirmation key
Hot water brewing
selection key
strong aroma
espresso coffee 08:33
strong aroma
double espresso 08:33
• To brew 2 cups, the machine dispenses half of the entered quantity and briefly interrupts dispensing in
order to grind the second serving of coffee.
Coffee dispensing is then restarted and completed. If a milk beverage has been chosen, the machine
automatically manages milk dispensing.
strong aroma
espresso coffee 08:33
SELECT THE DESIRED AROMA BEFORE
DISPENSING THE BEVERAGE.
medium aroma
espresso coffee 08:33
mild aroma
espresso coffee 08:33
pre-ground
espresso coffee 08:33
Click wheel
Select the coffee
bean dose or the
quantity of pre-
ground coffee

9
Open the milk compartment by
pressing the button and remove
the milk container.
Remove the cover and pour in the
milk. DO NOT EXCEED THE
MAXIMUM LEVEL shown in the
figure.
Replace the lid on the container
and place it back in the milk
compartment. Make sure to
carefully close the compartment.
21 3
MEDIUM
COFFEE
STRONG
COFFEE
MILD
COFFEE
SBS adjusts the intensity of the brewed coffee,
and can even be adjusted while brewing. Any
adjustment has an immediate effect on the
brewing coffee.
COFFEE INTENSITIY
SBS – SAECO BREWING SYSTEM
Height-adjustable drip tray.
To raise the drip tray, press lightly on the lower part of the button. To lower the tray,
press lightly on the upper part of the button; when the desired height is reached,
release the button.
Note: there is a red floater in the drip tray. When it rises, the tray must be emptied
and washed.
ADJUSTING THE HEIGHT OF THE DRIP TRAY
FILLING THE MILK CONTAINER
ADJUSTMENTS
The SBS system has been carefully designed to give your coffee the intense taste you desire. Simply
turn the dial and you will notice that the coffee goes from mild intensity to strong intensity.
Adjust the drip tray before dispensing any beverages.
The container with the cappuccinatore must be filled before preparing any milk beverage. Do not use
milk after the best-before date. (Important! Refer to the instructions for maintenance and cleaning of the
cappuccinatore on page 38).
S
C

10
1 2 3
THE DISPENSING OF COFFEE, HOT WATER AND MILK MAY BE STOPPED AT ANY TIME
BY PRESSING THE KEY AGAIN.
THE DISPENSED MILK MAY BE VERY HOT: DANGER OF SCALDING. AVOID TOUCHING
IT DIRECTLY WITH YOUR HANDS.
Check that all the containers are clean. To do this operation, follow the instructions in the “Cleaning and
Maintenance” chapter (see page 37)
WHEN YOU HAVE FINISHED PREPARING BEVERAGES CONTAINING MILK, PROCEED BY
CLEANING THE CONTAINER AND THE MACHINE’S CIRCUIT.
To brew 2 cups, the machine dispenses half of the entered quantity and briefly interrupts dispensing in order
to grind the second serving of coffee. Coffee dispensing is then restarted and completed. If a milk beverage
has been chosen, the machine automatically manages milk dispensing.
THE USED MILK HAS TO BE PROPERLY PRESERVED.
DO NOT USE IT AFTER THE BEST-BEFORE DATE SHOWN ON THE PACKAGE.
ESPRESSO / COFFEE / LONG COFFEE
Select the coffee aroma by
pressing the key one or
more times.
Press the key once for 1
cup and twice for 2 cups. The
selected beverage will be brewed.
BEVERAGE DISPENSING
This procedure shows how to dispense an espresso. To dispense another type of coffee, select it by sliding
the click wheel with a finger. Use appropriate espresso or coffee cups so that the coffee will not overflow.
The machine ends dispensing automatically according to the quantity determined by the manufacturer. It is
possible to customize this quantity. See page 16.
strong aroma
espresso coffee 08:33
strong aroma
espresso coffee 08:33
brewing in progress
espresso coffee
Select the desired beverage by
navigating the click wheel with
your finger.

11
4
1 2 3
5
DISPENSING BEVERAGES WITH GROUND COFFEE
Pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean
hopper. Pour in only coffee ground for espresso machines and never coffee beans or instant coffee. (see the
“Beverage programming” chapter on page 16).
WARNING: PUT PRE-GROUND COFFEE IN THE COMPARTMENT ONLY WHEN YOU WISH TO
DISPENSE THIS TYPE OF BEVERAGE.
INSERT ONLY ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE
DISPENSED AT THE SAME TIME.
Select the function by pressing
the key one or more times.
Press the key.
Pour ground coffee in the
appropriate compartment using
the measuring scoop provided in
the accessories.
Note:
• After 1 minute from when the message appears (2), if brewing has not started the machine will return to
the main menu and dump any inserted coffee into the coffee grounds drawer
• If no pre-ground coffee is poured into the compartment, only water will be dispensed
• If 2 or more scoops of coffee are added, the machine will not dispense the beverage and the coffee in the
compartment will be dumped into the coffee grounds drawer.
In the example given below, we chose to dispense an espresso using pre-ground coffee. The customized
choice of using pre-ground coffee is shown on the display.
strong aroma
espresso coffee 08:33
Select the desired beverage by
navigating the click wheel with
your finger.
pre-ground
espresso coffee 08:33
A message appears, reminding
the user to pour ground coffee in
the appropriate compartment.
add pre-ground coffee
espresso coffee
Press the key to start
brewing.
brewing in progress
espresso coffee
1.
2.

12
1 2 3
4 5 6
If the user wishes to continue preparing other drinks the
machine will keep the “rinsing milk circuit” signal
active.
After 20 minutes of inactivity, the machine requires the user to
perform a rinsing cycle as described in Step 7. If the machine is
turned off immediately after dispensing a milk beverage, the
next time the machine is turned on it will require the user to
perform a rinsing cycle.
Note: Before performing the “milk rinsing circuit” function
make sure that:
1. a large enough container is positioned under the
dispensing spout;
2. the water tank contains a sufficient quantity of water.
After 14 days from the first dispensing of
a milk-based beverage, the message
“milk circuit washing” is displayed; it is
advisable to clean the milk circuits as
shown on page 25.
After another 7 days the machine stops
dispensing milk-based beverage only and
the milk circuits must be washed; during
this phase, coffee and hot water may be
dispensed.
milk circuit washing
espresso coffee 08:33
BEVERAGE DISPENSING
After this, the machine allows you to
dispense more milk if you wish.
This option remains active for
approx. 3 seconds.
To activate it, press the
button. Once the desired quantity
has been reached, press the
button again to stop dispensing.
LATTE MACCHIATO
Fill the milk container
strong aroma
espresso coffee 08:33
Press the key.
strong aroma
latte macchiato 08:33
Select latte macchiato by navigating
the click wheel with your finger.
strong aroma
latte macchiato 08:33
Select the aroma by pressing the
key one or more times.
brewing in progress
latte macchiato
Press the key once for 1
cup and twice for 2 cups. The
latte macchiato will be brewed.
add milk?
latte macchiato
The machine will propose cleaning
the milk circuits.
Press the key to clean the
internal circuits.
rinsing milk circuit
latte macchiato 08:33
SEE INSTRUCTIONS ON PAGE 38 FOR OPTIMAL MILK DISPENSING

13
7 8 9
In this phase the user cannot
intervene and must wait until the
cycle finishes. After this, the
machine returns to the main
menu.
Remove the container, rinse
and dry.
rinsing milk circuit
in progress
milk circ. rinse cycle
Press to perform the rinse
cycle.
THIS PROCEDURE MUST BE PERFORMED FOR ALL MILK BEVERAGES!
AFTER USE, ALWAYS REMOVE THE MILK CONTAINER AND PUT IT IN THE REFRIGERATOR IF IT
CONTAINS REMAINING MILK.
THE CONTAINER MAY BE LEFT IN THE MACHINE ONLY IF IT HAS BEEN WASHED WITH
DRINKING WATER AND IT DOES NOT CONTAIN MILK (SEE PAGE 38).
After performing the rinse cycle, the machine reminds the user to
remove the container with the remaining milk through the message
“remove milk”.
REMOVE THE MILK CONTAINER ONLY WHEN THE MACHINE IS ON.
remove milk
espresso coffee 08:33

14
1 2 3
45
1 2 3
BEVERAGE DISPENSING
ESPRESSO MACCHIATO
CAPPUCCINO
When the “milk circuit rinsing”
symbol flashes, rinse the milk
circuits as described for the
latte macchiato (see page 12,
step 6).
strong aroma
espresso coffee 08:33
Press the key.
strong aroma
espresso macchiato 08:33
Select espresso macchiato by
navigating the click wheel with
your finger.
Select the aroma by pressing the
key one or more times.
strong aroma
espresso macchiato 08:33
strong aroma
espresso macchiato 08:33
If you wish, press the button.
Once the desired milk quantity has
been reached, press the
button again.
Press the key once or twice
to start brewing.
add milk?
espresso macchiato
strong aroma
espresso coffee 08:33
Press the key.
strong aroma
cappuccino 08:33
Select cappuccino by navigating the
click wheel with your finger.
Select the aroma by pressing the
key one or more times.
strong aroma
cappuccino 08:33
Fill the milk container
Fill the milk container

15
45
1 2 3
1 2
When the “milk circuit rinsing”
symbol flashes, rinse the milk
circuits as described for the
latte macchiato (see page 12,
step 6).
brewing in progress
cappuccino
If you wish, press the button.
Once the desired milk quantity has
been reached, press the
button again.
Press the key once or twice
to start brewing.
add milk?
cappuccino
DISPENSING HOT MILK
Repeat the operation to brew another cup of milk. When the “rinsing milk circuit” symbol flashes, rinse the
milk circuits as described for the latte macchiato (see page 12, step 6).
strong aroma
espresso coffee 08:33
Press the key.
hot milk 08:33
Select the hot milk and press the
key.
add milk?
hot milk
If you wish, press the
button. Once the desired milk
quantity has been reached, press
the button again.
Fill the milk container
HOT WATER DISPENSING
AT THE START, SHORT SPURTS OF HOT WATER MAY BE DISPENSED WHICH POSE A RISK
OF SCALDING. THE HOT WATER SPOUT CAN REACH HIGH TEMPERATURES: DO NOT
TOUCH IT WITH BARE HANDS.
The machine brews the
preset water quantity. Press
the key after brewing,
to exit the “Hot water”
function.
hot water 08:33
Press the key.
brewing in progress
hot water
Press the key to start
brewing.
1.
2.

16
select the quantity of coffee to be ground (opti-dose),
or select pre-ground coffee,
and/or set:
- coffee temperature
- coffee prebrewing
By sliding the click wheel with a finger
you can change the settings for:
- the quantity of coffee to be brewed;
- the quantity of milk to be dispensed;
- the coffee temperature;
- the coffee prebrewing.
restore factory settings
Select Coffee or Milk to
change the coffee dose per
cup.
save the new settings
1. PROGRAMMING FOR SELF-INSTRUCTING
Every beverage can be programmed according to your own tastes.
The following page describes how to program a beverage containing milk and coffee; the parameters to program
each beverage may differ according to the type of beverage.
For all beverages you can quickly program the quantity of coffee and/or milk dispensed in the cups whenever
the key is pressed.
Select the type of beverage you want to program, then press and hold the key until the display shows
(for example):
self-instruction active
espresso coffee
The machine dispenses coffee or milk.
When the desired amount is reached, press the key again.
The display will show:
(Only beverages with coffee and milk): for beverages with coffee and milk, you need to save the desired
quantity of both milk and coffee by pressing the button. This adjustment must be performed during the
relevant dispensing phase in the normal beverage dispensing process.
The dispensed quantity of coffee and/or milk remains stored and replaces any previous settings.
new quantity saved
espresso coffee
2. PROGRAMMING FROM THE “BEVERAGE SETTINGS” MENU
To set the beverage making parameters: press the key and select “beverage settings” by
turning the click wheel with a finger:
In this phase you can:
exit the program
mode.
beverage settings
BEVERAGE PROGRAMMING

17
1 2
4 5 6
7 8 9
10 11
Check that the water tank and coffee
bean hopper are full; place the cup
under the dispensing spout.
Press the button.
Press the button one or more
times to adjust the aroma or select
the use of pre-ground coffee. Press
the button to save.
Select the beverage to be
programmed. Press the
button to confirm.
Select “beverage settings”. Press
the button to confirm.
Change the coffee dose (amount of
water to be used) by navigating the
click wheel with your finger;
confirm with . Press to
change the parameter from coffee
to milk.
Change the milk dose by
navigating the click wheel with
your finger; confirm with .
Press the button for more than
two seconds to access the other
parameters to be programmed.
Change the temperature value
(high, medium, low) by navigating
the click wheel with your finger.
Press the button to save.
Press the button to select the
parameter prebrewing.
Change the prebrew value (normal, strong, off) by navigating the
click wheel with your finger. Press the button to save. Press
the button to exit.
Prebrewing: the coffee is
slightly dampened before
brewing to bring out the full
aroma of the coffee which
acquires an excellent taste.
3
1.
2. 1.
1.
3.
1.
2.
2.
2.
1.
2.
1.
2.
strong aroma
espresso coffee 08:33
beverage settings
latte macchiato
strong aroma
latte macchiato
coffee:¸¿¸¿
latte macchiato
milk :¸¿¸¿
latte macchiato
temperature: high
latte macchiato
temperature: high
latte macchiato
prebrewing: normal
latte macchiato
prebrewing: normal
latte macchiato
beverage settings

18
Some of the machine’s functions can be programmed to customize operations according to your
own tastes.
strong aroma
espresso coffee 08:33
Press the key to:
- confirm the selection;
- save the new settings.
1 Press the key.
2 Turn the click wheel with your finger to:
- select the functions
- change the function parameters.
beverage settings
Beverage settings
(already described on page 16).
machine settings
special functions
Machine settings (see page 19).
Special functions (see page 34).
To exit the program mode:
exit exit
or
PROGRAMMING THE MACHINE
1.
2.
1.
2.