Saeco Primea Touch Plus User manual

TABLE OF CONTENTS
Operation and maintenance manual
Before using the machine, please read the attached operating instructions.
Carefully read the safety rules
FOR HOUSEHOLD USE ONLY

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to person do not immerse
cord, plugs, or machine in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near
children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair or
adjustment.
7. The use accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cords hang over edge of table or counter, or touch hot surfaces.
10.Do not place on or near a hot gas or electric burner, or in a heated oven.
11.Always attach plug to appliance first, then plug cord into wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
12.Do not use appliance for than intended use.
13.Save this instructions.
SAVE THESE INSTRUCTIONS

CAUTION
This appliance is for household use only. Any servicing, other than cleaning and
user maintenance, should be performed by an authorized service centre. Do
not immerse machine in water. To reduce the risk of fire or electric shock, do not
disassemble the machine. There are no parts inside the machine serviceable
by the user. Repair should be done by authorized service personnel only.
1Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2Never use warm or hot water to fill the water tank. Use cold water only.
3Keep your hands and the cord away from hot parts of the appliance during
operation.
4Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6 Do not use caramelized coffee
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A. A short power-supply cord (or detachable power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
B. Longer detachable power-supply cords or extension cords are available and
may used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used,
1. The marker electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance
2. If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the counter
top or table top where it can be pulled on by children or tripped over.

2
GENERAL INFORMATION.................................................................................................................................3
MACHINE ........................................................................................................................................................4
ACCESSORIES ....................................................................................................................................................................4
INSTALLATION................................................................................................................................................5
STARTING THE MACHINE ........................................................................................................................................................5
MANUAL PRIMING OF THE WATER CIRCUIT....................................................................................................................................6
SETTING THE LANGUAGE AND THE CLOCK ....................................................................................................................................6
INTENZA WATER FILTER .........................................................................................................................................................7
DISPLAY .........................................................................................................................................................8
CHOOSE COFFEE AROMA........................................................................................................................................................8
ADJUSTMENTS...............................................................................................................................................9
COFFEE INTENSITIY..............................................................................................................................................................9
ADJUSTING THE HEIGHT OF THE DRIP TRAY. .................................................................................................................................9
FILLING THE MILK CONTAINER..................................................................................................................................................9
BEVERAGE DISPENSING................................................................................................................................10
ESPRESSO / COFFEE / LONG COFFEE .......................................................................................................................................10
DISPENSING BEVERAGES WITH GROUND COFFEE........................................................................................................................... 11
HOT WATER DISPENSING ...................................................................................................................................................... 12
LATTE MACCHIATO............................................................................................................................................................. 12
ESPRESSO MACCHIATO........................................................................................................................................................ 14
CAPPUCCINO ................................................................................................................................................................... 14
DISPENSING HOT MILK ........................................................................................................................................................ 15
BEVERAGE PROGRAMMING ..........................................................................................................................15
BEVERAGE PROGRAMMING MENU ............................................................................................................................................ 15
ESPRESSO / COFFEE / LONG COFFEE PROGRAM........................................................................................................................... 15
PROGRAMMING MILK BEVERAGES............................................................................................................................................ 16
PROGRAMMING THE MACHINE .....................................................................................................................18
MACHINE SETTINGS ........................................................................................................................................................... 18
LANGUAGE MENU ............................................................................................................................................................. 19
CUP ILLUMINATION MENU.................................................................................................................................................... 19
WATER FILTER MENU ......................................................................................................................................................... 19
WATER HARDNESS MENU - INTENZA AROMA SYSTEM ................................................................................................................... 20
RINSE MENU................................................................................................................................................................... 20
CUP WARMING PLATE MENU................................................................................................................................................. 21
ACCOUSTIC TONES AND ALARMS MENU.................................................................................................................................... 21
DISPLAY MENU ................................................................................................................................................................ 21
BEVERAGE SETTINGS..........................................................................................................................................................22
ADJUSTMENT OF THE COFFEE BREW TEMPERATURE ..................................................................................................................... 22
AROMA ADJUSTMENT FOR COFFEE BREWING.............................................................................................................................. 23
PREBREWING ADJUSTMENT (ONLY COFFEE BEVERAGES) ................................................................................................................ 23
ADDITIONAL FUNCTIONS ......................................................................................................................................................24
COFFEE OF THE WORLD FUNCTION ......................................................................................................................................... 24
DEMO MODE................................................................................................................................................................... 26
BEVERAGE COUNTER FUNCTION............................................................................................................................................. 26
MAINTENANCE..................................................................................................................................................................27
MILK CIRCUIT RINSE CYCLE.................................................................................................................................................. 27
MILK CIRCUIT WASH CYCLE.................................................................................................................................................. 28
COFFEE CIRCUIT CLEANING CYCLE (BREW GROUP WASH CYCLE) ....................................................................................................... 31
BLOCK DISPLAY .............................................................................................................................................................. 31
DESCALING .................................................................................................................................................................... 32
CLOCK SETTINGS ..............................................................................................................................................................34
TIME SETTING ................................................................................................................................................................. 34
AUTOMATIC TIMER SETTINGS................................................................................................................................................ 35
ENERGY SAVING SETTINGS................................................................................................................................................... 37
SPECIAL.........................................................................................................................................................................38
FACTORY SETTINGS........................................................................................................................................................... 38
CLEANING AND MAINTENANCE.....................................................................................................................39
MAINTENANCE DURING OPERATION..........................................................................................................................................39
GENERAL MACHINE CLEANING................................................................................................................................................39
MILK CONTAINER MAINTENANCE AND CLEANING...........................................................................................................................40
CLEANING THE BREW GROUP.................................................................................................................................................42
GRINDER MAINTENANCE ......................................................................................................................................................43
ERROR CODES ..............................................................................................................................................44
TECHNICAL DATA..........................................................................................................................................45
SAFETY RULES .............................................................................................................................................46
TABLE OF CONTENTS

3
The coffee machine is intended for preparing espresso by using either coffee beans or ground coffee. It
includes an automatic device for preparing milk beverages and a hot water dispenser.
The machine is elegantly designed for domestic use and is not suitable for continuous heavy duty or
professional use.
Warning: no liability is assumed for any damage caused by:
• Incorrect use not in accordance with the intended uses;
• Repairs not carried out by authorized customer service centers;
• Tampering with the power cord;
• Tampering with any part of the machine;
• The use of non-original spare parts and accessories;
• Failure to descale the machine or use at temperatures below 0°C.
IN THESE CASES, THE WARRANTY IS NOT VALID.
Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee
machine. For further information or if you experience problems not completely or sufficiently addressed in these
instructions, please contact an Authorized Customer Service Center.
KEEP THESE INSTRUCTIONS
A WARNING TRIANGLE DRAWS ATTENTION TO ALL THE INSTRUCTIONS THAT
ARE IMPORTANT FOR USER SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS
CAREFULLY TO AVOID SERIOUS INJURY!
HOW TO USE THESE OPERATING INSTRUCTIONS
GENERAL INFORMATION

4
Cappuccinatore
maintenance kit
Cit
Compartment for pre-
ground coffee
Brew group
Coffee grounds drawer
Socket for
power cord
Open coffee bean hopper
button
Coffee bean hopper
Cup warming plate
Main switch
Service door
ACCESSORIES
Coffee bean hopper cover
Drip tray
Button for raising/lowering
the drip tray
TOUCH SCREEN Display
SBS
Dispensing head
Drip tray + grill and float
Compartment for milk
container
Hot water spout
Water tank
Intenza water filter
Ground coffee
measuring scoop
Cleaning detergent
(Brew group)
Water hardness
tester
Grinder
adjustment key
MACHINE
Lubricant for the
brew group
Detergent for cleaning
milk container
Milk compartment
button

5
1 2 3
4
7
65
INSTALLATION
Attach the female end of the
power cord to the machine. Insert
the male end into the power
outlet.
Place a container beneath the hot
water spout.
Press the button on the coffee
hopper to open the cover. Fill the
hopper with coffee beans.
Close the cover pushing it down
completely.
Remove the water tank.
We recommend installing the water
filter (see page 7).
Press the main switch once to turn
on the machine. The appliance
automatically performs a diagnosis
of its functions. This test is
performed each time the machine
is turned on.
The machine automatically primes the water circuit.
The machine is now ready for use.
Water may not be dispensed into the glass.
This should not be considered a malfunction.
Make sure that the main power button is not switched to the “ON” position.
Fill the tank with fresh drinking
water. Do not exceed the “max”
level indicated on the water tank.
Once filled place the tank back
into the machine.
STARTING THE MACHINE
TO ADJUST THE WATER HARDNESS LEVEL AND SET
THE INTENZA AROMA SYSTEM SEE THE «WATER
HARDNESS MENU» ON PAGE 20.

6
1 3
Press to select the desired
language.
The machine starts and displays
the menu in the selected
language.
See manual on page 34 to
adjust the clock.
5
italiano (ch)
language
1/2
français
deutsch
nederlands
english
Italiano (i)
ok
1
Select the desired language.
Press for the other languages.
Press “ok”.
demo
self-test
4
italiano (ch)
language
1/2
français
deutsch
nederlands
english
Italiano (i)
ok
2
italiano (ch)
language
1/2
français
deutsch
nederlands
english
Italiano (i)
ok
3
If desired, the “demo” function (see page 26)
may be activated by pressing the key, each time
the machine carries out a self-diagnosis.
demo
self-test
4
MANUAL PRIMING OF THE WATER CIRCUIT
Position a container under the hot
water spout (it is possible that
water will not come out of the
spout).
Press the display once and the
machine will begin priming the
water circuit.
When the prime circuit cycle is
finished, remove the container.
The machine is now ready for
use.
INSTALLATION
SETTING THE LANGUAGE AND THE CLOCK
When the machine is switched-on for the first time, it requires the selection of the desired language.
This allows you to adjust the parameters of the beverages to the typical parameters of the country
where the machine is used. This is why some languages are differentiated also by country.
2
start
priming the machine
position the SBS system as shown
Manually prime the water circuit only when display (2) appears.
Note: first make sure that the water tank is full.
Important: before performing the circuit priming, position the SBS system (see page 9) as shown on the
display. Then adjust as desired.

7
56
9
4
13 2
Remove the small white filter
from the tank and store it in a dry
place sheltered from dust.
Fill the tank with fresh drinking
water and reinsert it into the
machine.
Set the Intenza Aroma System:
A = Light water
B = Medium water (standard)
C = Hard water
For further details see page 20
INTENZA WATER FILTER
To improve the quality of the water you use, and extend the life of your machine at the same time, it is
recommended that you install the water filter. After installation, go to the water filter initialization program
(see programming). In this way, the machine informs the user when the water filter must be replaced.
Remove the water filter from its packaging, immerse it vertically (with the opening facing upwards)
in cold water and gently press its sides so as to let the air bubbles out.
Insert the filter in its place within
the empty tank (see figure).
Press down until it clicks into
place.
Press "machine settings". Press "water filter". Press "water filter activation".
water
filter
inserted
not
inserted
water filter
activation
The machine performs the water filter initialization. Wait until the cycle stops automatically.
At the end of the initialization cycle, the machine returns to the product selection menu. Do not use the water
dispensed during this phase.
NOTE: if the Intenza water filter is not available, insert the small white filter previously removed (see
point 1) into the tank.
Place a container beneath the
hot water spout.
Press "programming menu".
show icon
explanation my custom
coffee program-
ming
menu
main-
tenance
main
menu
specials
machine
settings
clock
settings
extras
beverage
settings
energy
saving back to
coffee
menu
alerts &
acoustic
settings
machine
settings
display
language
rinsing
water
hardness
water
filter
cup
illumination
cup
warmer
go back restore default
settings
back to
menu go back restore
default
settings
back to
menu
save
settings
8
7

8
• To get the desired beverage, press the corresponding symbol on the display.
The machine automatically performs all the necessary operations.
• To make 2 cups, press the beverage symbol twice.
press twice
weak medium strong
The intensity of the color on the cup icon (only valid for coffee beverages) indicates the aroma, or
quantity of coffee to be ground, for preparing the beverage. The greater the quantity of coffee
ground the stronger the coffee will taste.
DISPLAY
Go to the "text
format" menu
Beverage
programming
Accessing the
programming menu
It is possible to change the type of display and choose between " icon format" and "text format"
ICON FORMAT
long
coffee
hot
water coffee espresso
hot
milk latte macchiato espresso
macchiato
cappuccino
medium strongmedium
medium strongmedium
Go to the "icon
format" menu
TEXT FORMAT
CHOOSE COFFEE AROMA
When the machine is programmed to use pre-ground coffee or when a beverage is customized, the
icon is displayed in a different way and/or accompanied by an asterisk (see section on
“programming beverages”.)
pre-ground customization
show icon
explanation my custom
coffee program-
ming
menu show
icon my custom
coffee program-
ming
menu

9
MEDIUM
COFFEE
STRONG
COFFEE
MILD
COFFEE
SBS adjusts the intensity of the brewed coffee,
and can even be adjusted while brewing. Any
adjustment has an immediate effect on the
brewing coffee.
COFFEE INTENSITIY
SBS – SAECO BREWING SYSTEM
Height adjustable drip tray.
To raise the drip tray, press lightly on the lower part of the button. To lower the tray,
press lightly on the upper part of the button; when the desired height is reached,
release the button.
Note: There is a red floater in the drip tray. When it rises, the tray must be emptied
and washed.
ADJUSTING THE HEIGHT OF THE DRIP TRAY
FILLING THE MILK CONTAINER
ADJUSTMENTS
The SBS system has been carefully designed to give your coffee the intense taste you desire. Simply
turn the dial and you will notice that the coffee goes from mild intensity to strong intensity.
Only the container with the cappuccinatore must be filled before preparing beverages with milk. Do not
use milk after the best-before date. (Important! Refer to the instructions for maintenance and cleaning
of the cappuccinatore on page 40).
Adjust the drip tray before dispensing any beverages.
21 3
Open the milk compartment by
pressing the button and remove
the milk container.
Remove the cover and pour in the
milk. DO NOT EXCEED THE
MAXIMUM LEVEL shown in the
fi g u r e .
Replace the lid on the container
and place it back in the milk
compartment. Make sure to
carefully close the compartment.
S
C

10
1 2 3
DISPENSING COFFEE, HOT WATER AND MILK CAN BE INTERRUPTED AT ANY TIME BY
SELECTING THE "STOP ... DISPENSING" BUTTON.
THE DISPENSED MILK CAN REACH HIGH TEMPERATURES: THERE IS A DANGER OF
SCALDING. DO NOT TOUCH IT WITH BARE HANDS.
Check that all the containers are clean. To do this operation, follow the instructions in the "Cleaning and
Maintenance" (see page 39).
WHEN YOU HAVE FINISHED PREPARING BEVERAGES CONTAINING MILK, PROCEED WITH
CLEANING THE CONTAINER AND THE MACHINE'S CIRCUIT.
To brew 2 cups, the machine dispenses half of the entered quantity and briefly interrupts dispensing in
order to grind the second serving of coffee. Coffee dispensing is then restarted and completed.If a milk
beverage has been chosen, the machine automatically dispenses the milk. If the first coffee is interrupted,
the second will not be dispensed.
THE MILK USED MUST HAVE BEEN PROPERLY PRESERVED.
DO NOT USE IT AFTER THE EXPIRATION DATE ON THE PACKAGE.
ESPRESSO / COFFEE / LONG COFFEE
Choose the beverage and press
the corresponding icon on the
display: once for 1 cup and twice
for 2 cups.
The machine begins grinding the
quantity of coffee entered.
Begin dispensing the selected
beverage.
stop
coffee
dispensing
espresso
BEVERAGE DISPENSING
This procedure shows how to dispense an espresso. To dispense another type of coffee, press the
appropriate icon. Use appropriate espresso or coffee cups so that the coffee will not overflow.
The machine ends dispensing automatically according to the quantity determined by the manufacturer. It is
possible to customize this quantity. See page 15.
If you wish to interrupt the dispensing cycle, press the " stop coffee dispensing" button.
show icon
explanation my custom
coffee program-
ming
menu

11
1 2 3
4 5
DISPENSING BEVERAGES WITH GROUND COFFEE
Pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean
hopper. Pour in only coffee ground for espresso machines and never coffee beans or instant coffee. (see the
"Beverage programming" chapter on page 15).
WARNING: PUT PRE-GROUND COFFEE IN THE COMPARTMENT ONLY WHEN YOU WISH TO
DISPENSE THIS TYPE OF BEVERAGE.
INSERT ONLY ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE
DISPENSED AT THE SAME TIME.
Press the appropriate button and
the display will show:
A message appears, reminder the
user to pour ground coffee in the
appropriate compartment.
add preground
coffee
start!
go
back
Press the "start! "button to start
dispensing.
Pour ground coffee into the pre-
ground coffee compartment using
the measuring scoop provided
with the accessories.
add preground
coffee
start!
go
back
Begins dispensing the selected
beverage.
long
coffee
stop
coffee
dispensing
Note:
• After 1 minute from when the message appears (2), if brewing has not started the machine will return to
the main menu and dump any inserted coffee into the coffee grounds drawer.
• If no pre-ground coffee is poured into the compartment, only water will be dispensed.
• If 2 or more scoops of coffee are added, the machine will not dispense the beverage and the coffee in the
compartment will be dumped into the coffee grounds drawer.
In the example given below, we chose to dispense a long coffee using pre-ground coffee.
The customized choice of using pre-ground coffee is shown on the display with an asterisk next to the
chosen beverage.
show icon
explanation my custom
coffee program-
ming
menu

12
2
23
4 5
1
1
6
Press the hot water icon once.
HOT WATER DISPENSING
WHEN THE HOT WATER BEGINS TO DISPENSE, SHORT SPURTS OF HOT WATER MAY BE
DISPENSED WHICH POSE A RISK OF SCALDING. THE HOT WATER SPOUT CAN REACH
HIGH TEMPERATURES: AVOID TOUCHING IT WITH BARE HANDS.
Begin hot water dispensing.
To dispense another cup of
hot water, repeat this
operation.
BEVERAGE DISPENSING
latte
macchiato
latte
macchiato latte macchiato
The machine begins grinding the
quantity of coffee entered.
Select the beverage and press the
corresponding icon on the
display: once for 1 cup and twice
for 2 cups.
When the coffee finishes grinding,
the machine will automatically
dispense the programmed quantity
of hot milk.
Once milk has been dispensed, the
machine automatically prepares the
coffee.
After this, the machine allows you to
dispense more milk if you wish. This
option remains active for
approximately 2 seconds. To activate,
press the “add milk” button.
The “milk rinsing” icon will flash
once the machine is done
dispensing in order to clean the
milk circuit. Press the “milk
rinsing” icon to clean the internal
milk circuit.
stop
milk
dispensing
add
milk
stop
water
dispensing
hot
water
milk
rinsing
Fill the milk container
LATTE MACCHIATO
show icon
explanation my custom
coffee program-
ming
menu
show icon
explanation my custom
coffee
program-
ming
menu
show icon
explanation my custom
coffee
program-
ming
menu
stop
coffee
dispensing
stop
milk
dispensing
stop
coffee
dispensing
SEE INSTRUCTIONS ON PAGE 40 FOR OPTIMAL MILK DISPENSING

13
9
start
rinsing
milk rinsing cycle
8
rinsing...
rinsing milk circuit-
please wait
If the user wishes to continue preparing other drinks the
machine will keep the “milk rinsing” signal active.
After 20 minutes of inactivity, the machine requires the user
to perform a rinsing cycle as described in Step 7.
If the machine is turned off immediately after dispensing a
milk beverage, the next time the machine is turned on it will
require the user to perform a rinsing cycle.
Note: Before performing the “milk rinsing” function make
sure that:
1. an adequate sized container is placed under the
dispensing head
2. the water tank is full of fresh water.
7
To perform a rinse cycle,
press “start rinsing”.
Wait for the cycle to be completed.
After this, the machine returns to
the main menu.
THIS PROCEDURE MUST BE PERFORMED FOR ALL MILK BEVERAGES!
AFTER USE, ALWAYS REMOVE THE MILK CONTAINER AND PUT IT IN THE REFRIGERATOR IF IT
CONTAINS REMAINING MILK.
Remove the container and put
it in the refrigerator if it
contains remaining milk.
THE CONTAINER MAY BE LEFT IN THE MACHINE ONLY IF IT HAS BEEN WASHED WITH
DRINKING WATER AND IT DOES NOT CONTAIN MILK (SEE PAGE 40).
After performing the rinse cycle, the machine reminds the user to
remove the container with the remaining milk through the message
“remove milk”.
REMOVE THE MILK CONTAINER ONLY WHEN THE MACHINE IS ON.
show icon
explanation my custom
coffee
program-
ming
menu
remove
milk
milk
cleaning
show icon
explanation my custom
coffee
program-
ming
menu
After 14 days from the first dispensing of
a milk-based beverage, the message
“milk cleaning” is displayed; it is
advisable to clean the milk circuits as
shown on page 28.
After another 7 days the machine stops
dispensing milk-based beverages and the
milk circuits must be washed; during this
phase, coffee and hot water may be
brewed.

14
231
45
23
4 5
1
BEVERAGE DISPENSING
espresso
macchiato
espresso
macchiato
cappuccino
cappuccino
cappuccino
ESPRESSO MACCHIATO
The machine begins grinding the
quantity of coffee entered.
Press the icon once for 1 cup and
twice for 2 cups.
Espresso macchiato begins
brewing.
Once the coffee has been brewed,
the machine automatically prepares
the hot milk.
CAPPUCCINO
The machine begins grinding the
quantity of coffee entered.
Press the icon once for 1 cup and
twice for 2 cups.
After this, the machine allows you to dispense more milk if you wish.
Press the “add milk” button within 2 seconds.
Fill the milk container
Fill the milk container
When the "milk rinsing"
symbol flashes, clean the
milk circuits as described for
latte macchiato (see page 12,
Step 6).
When the "milk rinsing"
symbol flashes, clean the
milk circuits as described for
latte macchiato (see page 12,
Step 6).
When the coffee finishes grinding,
the machine will dispense the
programmed quantity of hot milk.
Once milk has been dispensed, the
machine automatically prepares the
coffee.
add
milk
To dispense more milk, press the
“add milk” icon.
espresso
macchiato
show icon
explanation my custom
coffee
program-
ming
menu
show icon
explanation my custom
coffee
program-
ming
menu
stop
milk
dispensing
stop
coffee
dispensing
stop
milk
dispensing
stop
coffee
dispensing
stop
milk
dispensing
stop
coffee
dispensing
stop
milk
dispensing
stop
coffee
dispensing add
milk

15
2
1
2
1
BEVERAGE PROGRAMMING
BEVERAGE PROGRAMMING MENU
Hold down the beverage button for
two seconds
Press the button "my coffee" and
within two seconds, press the
beverage button
Each beverage can be programmed according to your individual taste. Customization is shown on the
display with the addition of an asterisk.
To program the desired beverage:
or
ESPRESSO / COFFEE / LONG COFFEE PROGRAM
Enter the menu of the beverage to
be customized by pressing and
holding the button for 2 seconds.
In this menu you can:
save settings.restore factory settings.
return to the
previous
window.
select the quantity
of coffee to be
ground (aroma).
go
back save
settings
restore
settings
strong preground
my
espresso
medium
light
start!
Once a beverage has been
customized it will only
dispense that type of
beverage. To change or modify
the beverage a new customi-
zation must be done.
Selecting a different quantity of coffee changes the aroma of the beverage.
show icon
explanation my custom
coffee
program-
ming
menu
show icon
explanation my custom
coffee
program-
ming
menu
show icon
explanation my custom
coffee
program-
ming
menu
select the use
of pre-ground
coffee.
hot
milk
DISPENSING HOT MILK
Press the hot milk icon once. The hot milk is dispensed.
Fill the milk container
To dispense another cup of milk,
repeat this operation.
When the "milk rinsing" symbol
flashes, clean the milk circuits as
described for latte macchiato
(see page 12, Step 6).
show icon
explanation my custom
coffee
program-
ming
menu
stop
milk
dispensing

16
1
5
6 7
BEVERAGE PROGRAMMING
To brew an amount of coffee greater
than that preset by the
manufacturer, press “custom
coffee amount” before the end of
the brew cycle in progress. When
the quantity is reached,
press “stop coffee dispensing”.
Pressing start! allows the
machine to brew coffee.
The machine automatically starts and
finishes brewing the coffee, according to
the standard settings.
The brew cycle may be
interrupted only by pressing
“stop coffee dispensing”.
If the button is not pressed,
the coffee can overflow in
the cup.
Once the brew cycle finishes,
press "save settings" within five
seconds.
If the "save settings" button
is not pressed the machine
returns to the main menu
and the customized settings
will not be saved.
saved!
The display shows the confirmation of
the memorized settings, and the
machine automatically returns to the
main menu.
PROGRAMMING MILK BEVERAGES
Enter the menu of the beverage to
be customized by pressing and
holding the button for 2 seconds.
In this menu you can:
select the
quantity of
coffee to be
ground. select the use
of pre-ground
coffee.
save settings.restore factory settings.
return to the
previous
window.
my
espresso
custom
coffee
amount
my
espresso
my
espresso
my latte
macchiato
Fill the milk tank
After pressing the start!
button, the brew cycle will
start.
my
espresso
my
espresso
show icon
explanation my custom
coffee
program-
ming
menu go
back save
settings
restore
settings
strong preground
medium
light
start!
go
back save
settings
restore
settings
strong preground
medium
light
start!
stop
coffee
dispensing
custom
coffee
amount
stop
coffee
dispensing
save
settings
go
back
3 4
2

17
8
9
Pressing start! allows the
machine to start the brewing
cycle.
The machine automatically starts and
finishes dispensing the milk,
according to the standard settings.
my latte
macchiato
To dispense an amount of milk greater than that preset by the
manufacturer, press “custom milk amount” before the end of the
dispensing cycle in progress. When the quantity is reached, press
“stop milk dispensing”.
The dispensing cycle may
be interrupted only by
pressing “stop milk
dispensing”.
If the button is not pressed,
the milk may overflow.
my latte
macchiato
The machine automatically starts
and finishes brewing the coffee,
according to the standard
settings.
my latte
macchiato
To brew an amount of coffee greater than that preset by the
manufacturer, press “custom coffee amount” before the end of the
brew cycle in progress. When the desired quantity is
reached, press “stop coffee dispensing”.
The brew cycle may be
interrupted only by pressing
“stop coffee dispensing”.
If the button is not
pressed, the coffee may
overflow.
save
settings
Once the brew cycle finishes,
press "save settings" within five
seconds.
If the "save settings" button
is not pressed the machine
returns to the main menu
and the customized settings
will not be saved.
saved!
my latte
macchiato
The display shows the confirmation of the
saved settings, and the machine
automatically returns to the main menu.
my latte
macchiato my latte
macchiato
After pressing the start!
button, the brew cycle will
start.
my latte
macchiato
go
back save
settings
restore
settings
strong preground
medium
light
start!
custom
coffee
amount
stop
coffee
dispensing
stop
milk
dispensing
custom
milk
amount
stop
milk
dispensing
custom
milk
amount
custom
coffee
amount
stop
coffee
dispensing
stop
milk
dispensing
custom
milk
amount
custom
coffee
amount
stop
coffee
dispensing
stop
milk
dispensing
custom
milk
amount
custom
coffee
amount
stop
coffee
dispensing
go
back
3
5
7
6
4

18 PROGRAMMING THE MACHINE
MACHINE SETTINGS
When the machine settings are selected the following screen appears. Here you can:
set the language of the menus.
set the illuminate cups function.
set the machine operation
through the water filter
set/activate the tones.
set the water hardness.
set the circuit rinse cycle.
set the operation of the cup warming plate.
set the brightness of the
display colors.
After having set each of the following menus, press
- "go back" to return to the previous screen
- "restore default settings" to restore the initial values
- "save settings" to save the settings
- "back to menu" to return to the main menu
Some of the machine’s functions can
be programmed to customize
operations according to your own
requirements.
Press the "programming menu" button.
The programming menu will access:
Programming the machine
operations (see page 18)
Special functions
(see page 38)
Maintenance (cleaning the
machine) (see page 27)
In depth beverage programming
(see page 22)
- Current date and time
- Standby timer
- Times to turn on/turn off over
the span of a day (see page 34).
Extra functions (see page 24)
Activate standby Exit
show icon
explanation my custom
coffee program-
ming
menu
main-
tenance
main
menu
specials
machine
settings
clock
settings
extras
beverage
settings
energy
saving
back to
coffee
menu
alerts &
acoustic
settings
machine
settings
display
language
rinsing
water
hardness
water
filter
cup
illumination
cup
warmer
go back restore
default
settings back to
menu