SAF-HOLLAND RK-09429-5 User manual

REMOVAL AND REPLACEMENT PROCEDURES:
1. Remove the old cotter pin, washer, release
handle, and spring and discard. Slide the new
release handle through the left (driver) side
release handle window (see Figure 1).
XL-FW345
Installation Instructions for RK-09429 and RK-09429-5
FleetMaster Generation I or II
(Left-Hand) Release Handle Kit
To complete the replacement procedures, the tractor must be uncoupled
from the trailer and parked, with the engine turned off, in an area clear
of other persons, vehicles, or obstacles.
INSERT NEW HANDLE THROUGH DRIVER
SIDE RELEASE HANDLE WINDOW
RELEASE
ARM
FIGURE 1
GENERAL INFORMATION:
1. All fifth wheel maintenance, adjustment and
rebuilding must be performed by a qualified
person using proper tools and safe practices.
2. Do not modify or add to the product.
3. Always wear safety goggles and never strike
any part with a steel hammer.
4. Do not weld on this product.
5. Observe standard safety precautions
at all times.
6. Use only genuine Holland parts.
7. Do not deviate from these instructions. Refer
to Holland publication XL-FW340 for Holland
TF-TLN-5001 Lock Tester instructions.
WARNING
WARNING
This release handle replacement kit is intended ONLY for LEFT-HAND release Generation
I and II (Gen. I and Gen. II) FleetMaster fifth wheels produced before September 1999.
Verify that your FleetMaster fifth wheel is a Gen. I or Gen. II by identifying the proper
fifth wheel lock AND handle shown below. If your fifth wheel has a Gen. III lock or
handle, DO NOT USE THIS KIT! Contact Holland for the proper kit part number.
✔
✔GEN. I
LOCKSRK-09429 and RK-09429-5 COMPATIBILITY HANDLES
GEN. II
GEN. III
2
OK
OK

★Holland Hitch Co. ★Holland Hitch of New Jersey ★Holland Atlantic Hitch Co. ★Holland Hitch of Texas, Inc. ★Holland Pacific Hitch Co. ▲Holland Binkley Co. ▲Holland Binkley Co.
Holland, MI 49423 Whitehouse Station, NJ 08889 Denmark, SC 29042 Wylie, TX 75098 Milpitas, CA 95035 Warrenton, MO 63383 Axle Products Division
[phone] [phone] [phone] [phone] [phone] [phone] Delphos, OH 45833
[phone] [phone] [phone] [phone] [phone] FAX [phone] [phone]
FAX [phone] FAX [phone] FAX [phone] FAX [phone] FAX [phone] FAX [phone]
★Holland Hitch of Canada, Ltd. ▲Holland Equipment, Ltd. ★Holland Hitch Western, Ltd. ✚Eurohitch, GmbH. ✚Eurohitch (U.K.), Ltd. Holland Transtrade Nippon Holland, Ltd. ✚Holland Hitch (Aust.), Ltd.
Woodstock, Ontario N4S 7Z5 Norwich, Ontario N0J 1P0 Surrey, BC V3S 5K1 Schloss Holte Tipton, West Midlands Far East Sdn. Bhd. Tokyo, Japan Melton, Victoria, Australia
[phone] [phone] [phone] Germany United Kingdom Kuala Lumpur, Malaysia [phone] (03) 9743-6799
FAX [phone] FAX [phone] FAX [phone] (05207) 89560 [phone] (03) 734-2888 FAX [phone] FAX [phone]
FAX [phone] FAX [phone] FAX [phone]
Copyright © August 1999 Holland Hitch Company
FIGURE 8
FIGURE 2
FIGURE 3 FIGURE 4
FIGURE 5 FIGURE 6
2. Install the new spring on the
new handle. To do this, start by
inserting the long loop end of
the spring on the handle, as
shown in Figure 2.
3. Slide the spring along the
handle towards the loop retainer
(see Figure 3). Rotate the spring on
the handle so that the spring
loop opening is aligned with
the loop retainer (see Figure 4).
Align the end of the spring loop
with the loop retainer opening
(see Figure 5). Rotate the spring
to engage the spring end in the
loop retainer (see Figure 6).
4. Hook the short loop down
through the casting lug
(see Figure 7)
5. Now, slide the bent end of the
release handle down through
the hole in the end of the release
arm (see Figure 8).
6. Place a new washer over the end
of the release handle and secure
with the new cotter pin (Figure 8).
7. IMPORTANT! When completing
the replacement procedures,
check the operation of the fifth
wheel by locking and unlocking
the fifth wheel at least three
times, using a Holland Lock
Tester (part number TF-TLN-
5001). Refer to Holland
publication XL-FW354,
“FleetMaster Fifth Wheel
Maintenance Procedures,”
for other important routine
maintenance and inspection
requirements.
LONG LOOP
LOOP
RETAINER
SLIDE SPRING
SHORT LOOP
LOOP
RETAINER
LOOP
RETAINER
LOOP
RETAINER
LOOP
RETAINER
FIGURE 7 RELEASE HANDLE
(CROSS CUT)
CASTING LUG
LONG
LOOP
SHORT
LOOP
WASHER
COTTER
PIN
RELEASE HANDLE
RELEASE ARM LEFT (DRIVER) SIDE CASTING LUG