Safe Fleet 00-1109 R5 User manual

© 2021 Safe Fleet | All rights reserved | Part #700-1109 R5 © 2021 Safe Fleet | All rights reserved | Part #700-1109 R5
LCD Monitor Configuration
For information on custom monitor settings, see the Rear Vision Monitor Quick Install Guide (700-1107)
Related Documents
For full product details, and access to our Document Library, please visit the Seon Community Web site:
https://community.safefleet.net
If you do not have access credentials, please contact Customer Service.
Customer Service
•Service: 1.844.899.7366
•General Enquiries: 1.877.630.7366
•Email: [e-mail]
If your RVS device is to be returned, please contact Customer Service, and provide the model and/or serial number of your
unit. Ask for a Return Merchandise Authorization (RMA) number. An RMA number allows the Service Technicians to
better track your product when it comes in for service. Please show the RMA number on the outside of the package. ANY
RETURNED PRODUCT WITHOUT AN RMA NUMBER MAY BE REFUSED.
Warranty
For full warranty information, please visit:
http://www.seon.com/documents/Seon-Warranty.pdf
Rear Vision System with Video Splitter
Installation Guide
Introduction
The RVS (Rear Vision System)for vehicles enables the driver to see the camera output on a dash-mount monitor
whenever the reverse signal is triggered. This guide covers the RVS with video splitter system configuration.
Note: High definition camera views cannot be displayed on the monitor.
When installed, the RVS typically operates as follows:
•The monitor is usually OFF (dark)
The monitor only turns ON when the vehicle is put into reverse gear (REVERSE signal is applied to the RVS)
A video source goes directly to the monitor, and can be mirrored with monitor settings. A second feed is sent from the
video splitter to the recorder. Video from the rear view camera and events (including alarms) are recorded.
The camera and monitor receive switched power separately from the recorder:
•The camera and monitor continue to operate independently if the recorder has no power or fails
•RVS video and events are not recorded when switched (accessory) power is off
System Installation Components
Rear view camera with corresponding mounting hardware. Option A: HExHD or HEHDxx camera harness
Option B: 75’ Camera extension cable (060-1094)
Camera cable adaptor for retrofit (060-1095)
7” Monitor (080-1059), including sunshade (665-1020),
bracket (660-1073), and hardware kit (020-1042)
Rear Vision Monitor Quick Install Guide (700-1107)
20’ Video extension cable (HEHD20)
Monitor power and connector harness (060-1096)
RCA cable adaptor (060-1102)
Video splitter (050-0217)
20’ BNC to Microfit video adaptor cable (060-0678)
Monitor diode kit (020-1045)

Monitor, Camera, and Video Splitter Connections
Use the following image and steps to connect the monitor and camera, and the video splitter:
1. Once the camera is installed according to its installation documentation, connect cable Ato the TO CAMERA
port on the rear of the video splitter
2. Connect the BNC on cable Bto VIDEO OUT on the rear of the splitter.
3. Connect the 2x3 Microfit connector on cable Bto the BACK AV3 Microfit socket on cable D.
4. Connect a 2x3 Microfit connector on cable C to the TO DVR port on the front of the video splitter.
5. Connect cable Cto a camera port on the back panel of the recorder.
Take note of the camera channel number – you’ll need it for the Recorder Configuration procedure, below.
6. Install the monitor bracket and mount the monitor on the dashboard.
For details, see the Rear Vision Monitor Quick Install Guide (700-1107).
7. Connect the monitor output from cable Dto the monitor input cable.
Verify that the arrows on the connector ends are aligned.
8. Connect the BACK TRIGGER AV3 (blue) fly wire from cable Dto the striped end of the supplied diode.
9. Connect the unmarked end of the supplied diode to the reverse signal input (active high trigger).
10. Connect the GND (black) fly wire from cable Dto battery negative.
11. Connect the POWER (red) fused fly wire from cable Dto 12V ignition (switched source) power.
12. (Optional) Attach the M12 socket on cable adaptor Eto the LEFT AV1 input on cable D.
The RCA jacks on cable Eaccept composite video input from an accessory device. To use the standard definition
video output (CVBS) from an inView 360 HD system, connect the adapter cable 060-1199 to an RCA input on
cable E. For more information, visit the Seon Community (https://community.safefleet.net).
13. See “Power On and Test”.
Power On and Test
1. Turn on accessory power to the vehicle.
2. Put the vehicle in reverse gear.
During normal operation, the monitor only turns on
when the vehicle is shifted into reverse.
If the monitor fails to turn on when power is applied,
confirm power connections. Disconnect and firmly
reconnect the LCD Monitor cables.
3. Configure the recorder (see Recorder Configuration,
below).
4. Adjust the camera view so that the bumper of the
vehicle is just visible across the bottom edge of the
monitor, as shown.
5. Refer to the camera installation guide for details on
closing and fastening the camera once it has been
aimed.
6. Turn off accessory power to the vehicle.
Recorder Configuration
To configure the recorder to properly record the
camera information:
1. On the recorder, connect a diagnostic monitor to the
front Video Out RCA jack, and plug in a USB mouse.
2. Right-click anywhere on the screen to display the
Main Menu, then select Configuration.
Recorder Configuration (continued)
3. Select RecordCamera
Ensure the camera channel you connected to the RVS
feed from the splitter has FPS set (not OFF). Channel 3
is used in the example:
4. Click Back twice to save any changes and return to the
Configuration tab.
5. Exit recorder Configuration menus.
6. Reboot the recorder and test the monitor view with the
vehicle in reverse.
7. Disconnect the diagnostic monitor and mouse.
Monitor trigger inputs
expect an Active H/L signal.
Voltage references:
Active H: DC 3.3V - 36V
Active L: < DC 3.3V