Safe Fleet RVS-6035 User manual

Rear View Monitor
Instruction Manual
©Rear View Safety 2022
3-Channel TFT 5” LCD Digital Color
Rear View Monitor (with Power Harness)
RVS-6035

2©Rear View Safety
Introduction ...................................................................................................3
In The Box ......................................................................................................3
SafetyInformation......................................................................................4-6
Before Beginning Installation ....................................................................7
Installation Guide ..........................................................................................8
Replacement Installation Diagram ..........................................................8
WiringCamera&Monitor........................................................................9-10
Connection Diagram ..................................................................................11
Monitor Operation .....................................................................................12
Splitting & Splicing ...................................................................................13
Positioning ...................................................................................................14
Monitor Dimensions ...................................................................................15
Monitor Specifications ...............................................................................16
Troubleshooting............................................................................................17
Warranty ......................................................................................................18
Disclaimer ....................................................................................................19

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
3
IN THE BOX
Congratulations on purchasing a Rear View Backup Camera System!
With this manual you will be able to properly install and operate the unit.
The Backup Camera System is intended to be installed as a supplement aid to
your standard rear view mirror that already exists in your vehicle. The Backup
Camera System should not be used as a substitute for the standard rear view
mirror or for any other mirror that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a motor vehicle equipped
with a TV viewer or screen located forward of the back of the driver’s seat or in
any location that is visible, directly or indirectly, to the driver while operating the
vehicle.
Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
1 - 5”TFT LCD Digital Color Monitor
1 - U-Bracket Mount
1 - Flush Mount Bracket
1 - Power Harness with 3 Camera Inputs
1 - Remote Control
1 - Screw Kit for installation

4©Rear View Safety
SAFETY INFORMATION
USAGE : The Rear View Camera System is designed to help the driver safely
detect people and/or objects helping to avoid damage or injury. However, you
the driver, must use it properly. Use of this system is not a substitute for safe,
proper or legal driving.
• Never back up while looking at the monitor alone. You should always check
behind and around the vehicle when backing up, in the same way as you would
if the vehicle did not have the Rear View Camera System. If you back up while
looking only at the monitor, you may cause damage or injury. Always back up
slowly.
• The Rear View Camera System is not intended for use during extensive back-
up maneuvers or backing into cross trac or pedestrian walkways.
• Please, always remember, the area displayed by the Rear View Camera System
is limited. It does not display the entire panorama that is behind you.
PLEASE READ THE ENTIRE MANUAL AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CAREFULLY. FAILURE TO DO SO CAN CAUSE SERIOUS
DAMAGE AND/OR INJURY, INCLUDING LOSS OF LIFE. BE SURE TO OBEY ALL
APPLICABLE LOCAL TRAFFIC AND MOTOR VEHICLE REGULATIONS AS IT
PERTAINS TO THIS PRODUCT. IMPROPER INSTALLATION WILL VOID
MANUFACTURER’S WARRANTY.

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
5
SAFETY INFORMATION
INSTALLATION
Electric shock or product malfunction may occur if this product
is installed incorrectly.
• Use this product within the voltage range specified. Failure to do so can
cause electronic shock or product malfunction.
• Take special care when cleaning the monitor.
• Make sure to firmly ax the product before use.
• If smoke or a burning smell is detected, disconnect the system immediately.
• Where the power cable may touch a metal case, cover the cable with a
friction tape. A short circuit or disconnected wire may cause a fire.
• While installing the RVS System be careful with the wire positioning in
order to avoid wire damage.
• The RVS System should only be used when the vehicle is in reverse.
• Do not watch movies or operate the monitor while driving; as it may cause
an accident.
• Do not install the monitor where it may obstruct drivers view or obstruct an
air bag device.
• Dropping the unit may cause possible mechanical failure.
• When in reverse, monitor buttons are not functional

6©Rear View Safety
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
If you have questions about this product,
please contact us at:
800.764.1028 [e-mail]
www.rearviewsafety.com
New York
1797 Atlantic Ave
Brooklyn, NY 11233
Indiana
319 Roske Dr.
Elkhart, Indiana 46516
Canada
68 Trafalgar Square
Thornhill, ON, L4J 7M5, Canada

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
7
BEFORE YOU BEGIN INSTALLATION
Before drilling please check that no cable or wiring is on the other side of the
wall. Please clamp all wires securely to reduce the possibility of them being
damaged while vehicle is in use.
Keep all cables away from hot or moving parts and electrical noisy
components.
We recommend doing a benchmark test before installation to insure that all
components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8" (20mm) hole should
be drilled for passing camera cable through vehicles walls.
Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform a system
function test by temporarily connecting the system.
If the system seems to not be operating properly see troubleshooting (page 18).

8©Rear View Safety
INSTALLATION GUIDE
Cable
1. Be sure to position the cable properly. The aviation camera cable uses
aircraft grade connectors which means the camera cable can be exposed to
all weather elements. Do not run the cable over sharp edges, do not kink the
cable and keep away from HOT and rotating parts.
2. Fasten all cables and secure all excess cable.
Monitor
1. To Attach the Pedestal mount to the dashboard or to the
headliner use self-tapping screws and/or the adhesive pad.
2. Attach monitor to mount, and adjust mounting angle to allow
optimum driver viewing comfort.

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
9
The Power Harness
• To power the system connect the power (RED) 12V+ wire to ignition power and
the ground (BLACK) wire to chassis ground.
• These are the only wires needed to power the entire system and all the
cameras. Each camera can be seen at any time by simply pressing the power
button and using the V1/2 button to toggle.
• The three positive trigger wires (WHITE-CH1, BROWN-CH2, BLUE-CH3) each
represent one channel and will turn on their channel when the trigger wire
is energized with 12V.
• "Camera 3" is the designated backup channel. To have the the backup camera
come on when you go into reverse, connect the BLUE wire to reverse
power (or any power source that comes on only in reverse).
• The other channels can similarly be triggered (i.e. side cameras can be
triggered by the turn signals etc.)
• To automatically have camera and monitor turn ON when vehicle activates,
simply twist BLUE positive trigger 12V+ to Red Power line 12V+ and wire to
ignition power.
Note: This setup will disable the menu in channel 3.
To access the menu simply move to channel 1 or 2 and
all the changes will apply to channel 3.
Note: When the blue wire is active it will have
precedence over the other triggers. Therefore, if you
wish to use multiple triggers, do not attach the blue
trigger to constant power.
WIRING CAMERA AND MONITOR

10 ©Rear View Safety
Audio: There is audio on channels 2 and 3. On channel 3 the blue trigger wire
must be energized (12V) to activate the audio. On channel 2 the audio
is always on.
Grid-lines: The grid-lines are also carried through the blue wire. To use the
grid-lines for reversing, connect the blue wire to a reverse power.
There is a built-in voltage regulator for our systems which can handle 12-24
volts. Real consumption is 10 to 30 Volts.
Note: The camera and monitor can always be activated
by manually pushing the power button on monitor. This is
in addition to utilizing the positive triggers..
Note: If connecting power directly to battery, the camera
is always ON and therefore can drain battery.
It is recommended to connect power to an ignition
switched accessory power source.
WIRING CAMERA AND MONITOR

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
11
CONNECTION DIAGRAM

12 ©Rear View Safety
MONITOR OPERATION
To turn on the monitor, press “ON” button.
• To adjust brightness, press “MENU” 1 time and use arrows
• To adjust contrast, press “MENU” 2 times and use arrows
• To adjust saturation, press “MENU” 3 times and use arrows
• To adjust sharpness, press “MENU” 4 times and use arrows
• To adjust volume, press “MENU” 5 times and use arrows
• To change language, press “MENU” 6 times and use arrows
• To activate rotate image option, press “MENU” 7 times and use arrows.
• To activate day/night option, press “MENU” 10 times and use arrows
• To reset your system, press “MENU” 11 times and use arrows
• To view images on other cameras, press “CAMERA SELECTION”
1 time for camera one, 2 times for camera two and 3 times for camera three.

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
13
SPLITING & SPLICING
1. Red - Power (+)
2. Yellow - Video
3. Green - Mirror / Normal Imaging
4. White - Audio
5. Black - Ground (-)

14 ©Rear View Safety
POSITIONING

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
15
MONITOR DIMENSIONS

16 ©Rear View Safety
SPECIFICATION
Monitor Type TFT LCD Digital Monitor
Screen Size 5”
Dimensions 6.6"L x 5"H x .8"D
Video Input 3CH
Active Area 110.88mm(W) x 62.832mm(H)
Dot Resolution 480 x 3 (RGB) x 272
Display Format 16:9
Video System Auto PAL / NTSC
Contrast 500:1
Brightness 300cd/m2
View Angle U: 40°/ D:40°L/R:70°
Power Supply DC 10.5V~ DC 36V
Remote IR Remote Control
Sunshade Yes
Operating Temperature -20°C ~ +70°C
Storage Temperature -30°C ~ +80°C
Vibration Rating 5G
Net Weight 400g
Sync System Internal

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
17
TROUBLESHOOTING
Monitor Displays Blue Screen & Displays No Signal
• Do a hard reset, unplug all cables and power cables and leave out for 1
minute and then re-connect them.
• Check to ensure that the connection to the camera is tight.
• Verify camera cable is plugged into port labeled Backup Camera
• Verify that the blue positive trigger on power harness is put to power 12v+.
• If the problem still persists, verify that alternate ports work. If alternate
ports do not work, remove Blue Trigger wire from 12V+ and select alternate
channels.
Monitor Will Not Power-Up (no backlight on power button)
• Check fuse
• Check 12v+ to monitor
• Check ground connection
No Image On Screen
• Verify camera is in correct camera input
• Verify cable is connected to monitor
• Verify camera is connected to cable
• Connect known working camera and cable to monitor.
• Verify Blue trigger is receiving power
Audio on Camera (optional)
• Verify chosen camera has audio
• Verify volume setting
• Confirm that the Blue audio trigger is connected to 12v+

18 ©Rear View Safety
ONE YEAR WARRANTY
REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A
PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR
REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC.
IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER
INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW
SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
THIS WARRANTY IS VOID IF: DEFECTS IN MATERIALS OR WORKMANSHIP OR DAMAGES
RESULT FROM REPAIRS OR ALTERATIONS WHICH HAVE BEEN MADE OR ATTEMPTED BY
OTHERS OR THE UNAUTHORIZED USE OF NONCONFORMING PARTS; THE DAMAGE IS DUE
TO NORMAL WEAR AND TEAR, THIS DAMAGE IS DUE TO ABUSE, IMPROPER MAINTENANCE,
NEGLECT OR ACCIDENT; OR THE DAMAGE IS DUE TO USE OF THE REAR VIEW SAFETY, INC.
SYSTEM AFTER PARTIAL FAILURE OR USE WITH IMPROPER ACCESSORIES.
WARRANTY PERFORMANCE
DURING THE ABOVE WARRANTY PERIOD, SHOULDYOUR REAR VIEW SAFETY PRODUCT
EXHIBIT A DEFECT IN MATERIAL ORWORKMANSHIP, SUCH DEFECTWILL BE REPAIREDWHEN
THE COMPLETE REAR VIEW SAFETY, INC. PRODUCT IS RETURNED, POSTAGE PREPAID AND
INSURED, TO REAR VIEW SAFETY, INC. OTHER THAN THE POSTAGE AND INSURANCE
REQUIREMENT, NO CHARGEWILL BE MADE FOR REPAIRS COVERED BYTHIS WARRANTY.
WARRANTY DISCLAIMERS
NOWARRANTY, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, OTHER THE ABOVEWARRANTY
IS MADEWITH REGARDTOTHIS REARVIEW SAFETY, INC.REARVIEW SAFETY, INC.DISCLAIMS
ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR
PURPOSE AND ALL OTHER WARRANTIES IN NO EVENT SHALL REAR VIEW SAFETY. INC.
LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES OR FOR
ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGEDTO BE AS A
CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING,
BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.

Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
800.764.1028 [email protected]
www.rearviewsafety.com
19
DISCLAIMER
REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE
USER OF OUR SYSTEMSWILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE
WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL
AND CAUTIOUS DRIVING OR FORTHE CONSISTENT ADHERENCETO ALL APPLICABLE TRAFFIC
LAWS AND MOTOR VEHICLE SAFETY REGULATIONS. THE REAR VIEW SAFETY PRODUCTS ARE
NOT A SUBSTITUTE FOR REAR VIEW MIRRORS OR FOR ANY OTHER MOTOR VEHICLE
EQUIPMENT MANDATED BY LAW. OUR CAMERA SYSTEMS HAVE A LIMITED FIELD OF VISION
AND DO NOT PROVIDE A COMPREHENSIVEVIEW OFTHE REAR OR SIDE AREA OFTHEVEHICLE.
ALWAYS MAKE SURETO LOOK AROUNDYOURVEHICLE AND USEYOUR MIRRORSTO CONFIRM
REARWARD CLEARANCE AND THAT YOUR VEHICLE CAN MANEUVER SAFELY. REARVIEW
SAFETY AND/OR ITS AFFILIATES SHALL HAVE NO RESPONSIBILITY OR LIABILITY
FOR DAMAGE AND/OR INJURY RESULTING FROM ACCIDENTS OCCURRING WITH VEHICLES
HAVING SOME OF REAR VIEW SAFETY PRODUCTS INSTALLED AND REAR VIEW SAFETY AND/
OR ITS AFFILIATES, THE MANUFACTURER, DISTRIBUTOR AND SELLER SHALL NOT BE LIABLE
FOR ANY INJURY, LOSS OR DAMAGE, INCIDENTAL OR CONSEQUENTIAL, ARISING OUT OF THE
USE OR INTENDED USE OF THE PRODUCT. IN NO EVENT SHALL REAR VIEW SAFETY AND/OR
ITS AFFILIATES HAVE ANY LIABILITY FOR ANY LOSSES WHETHER DIRECT OR INDIRECT, IN
CONTRACT, TORT OR OTHERWISE INCURRED IN CONNECTION WITH THE SYSTEMS,
INCLUDING BUT NOT LIMITED TO DAMAGED PROPERTY, PERSONAL INJURY AND/OR LOSS OF
LIFE. NEITHER SHALL REAR VIEW SAFETY AND/OR ITS AFFILIATES HAVE ANY
RESPONSIBILITY FOR ANY DECISION, ACTION OR INACTION TAKEN BY ANY PERSON IN
RELIANCE ON REAR VIEW SAFETY SYSTEMS, OR FOR ANY DELAYS, INACCURACIES AND/OR
ERRORS IN CONNECTION WITH OUR SYSTEMS FUNCTIONS.

Engineered For Vehicle SafetyTM
If you have questions about this product,
please contact us at:
800.764.1028 [e-mail]
www.rearviewsafety.com
New York
1797 Atlantic Ave
Brooklyn, NY 11233
Indiana
319 Roske Dr.
Elkhart, Indiana 46516
Canada
68 Trafalgar Square
Thornhill, ON, L4J 7M5, Canada