SAFECONTROL Touch-101-A9 User manual

LAN
12/24VDC
SAFECONTROL s. r. o.
Vaníčkova 315/7
169 00 Praha 6
IČO: 02084287
DIČ: CZ02084287
[e-mail]
www.safecontrol.cz
Touch-101-A9
Touch-101-A11
Installation guide
Mounting
Connection
1
Connect the supply voltage to the pa-
nel using the supplied DC connector.
2
Made in Czech Republic
Connect the Ethernet cable
to the ETH port.
1
2
Prepare a hole of the size
256 x 174 mm.
1
4x
4x
1
Information for users on the disposal of electrical and electronic equipment
(corporate and enterprise use)
For proper disposal of electrical and electronic equipment, request detailed
information from your dealer or suppliers.
Information for users on the disposal of electrical and electronic equipment
in other countries outside the European Union
The below symbol is only valid in the countries of the European Union. For proper
disposal of electrical and For detailed information, contact your local authorities
or equipment retailer.
Secure the panel with
screws and struts.
Panel with a sheet thickness
of max. 2.5 mm.
2
1
2
256 mm
174 mm
1
3
3

Settings
2:15
On
Static configure
OKCANCE L
Settings
2:15
On
Settings
2:15
Service PIN ENTER
Enter Password
1 2 3
4 5 6
7 8 9
0 CL R
OKCANCELCLOSING IN 2 3
1066 ENTER
Server Unavailable
TR Y RECONNECT NOW !
1066 ENTER
Server Unavailable
TR Y RECONNECT NOW !
Home page
settings
Entrance to the service
menu
Click here and enter the pin
code „1066“.
Default DHCP client settings
switch to „Static IP“.
1066
ENTER
Set the target address at the format
below: http(s)://192.168.10.250/display.
Select http or https according to
the server. If you use it in conjunction with
the SAFECONTROL WEBserver, write
after the address/display for registration
to automatically log in.
Press the button to save the settings
and exit this menu. By pressing
reconnect buttons to verify server
availability. If the server is still not
available, check the network
connection and hardware settings.
You have now entered the service
menu of the tablet and kiosk applica-
tion. We recommend that you do not
change the default kiosk application
settings without consulting with techni-
cal support. Undesirable changes can
cause the touch panel malfunction.
Press the gear symbol in the upper right
corner to confi gure the network interface.
To enter the
service menu,
tap the display
5-times in
quick suc-
cession. The
window for
entering the
PIN code will
appear „1066“.
A confi guration window will appear,
where all setting parameters must
be fi lled in correctly
Fill in the touch panel‘s IP address,
mask, gateway, DNS server and save
the settings.
To exit the service menu, click on the
„exit“ button on the right the top corner
of the application.
Then confi rm that you should always start
the SAFECONTROL kiosk application.
The most important confi guration in hardware settings is the
network interface. The default Ethernet port setting is DHCP Client.
If a DHCP server is not available on the network, it is necessary
to set a static IP address, gateway, etc.
Additional hardware parameters can be set in other parts
of the menu (e.g., time or time zone).
The touch panel can also be connected via WiFi. In this case, go
to the touch panel settings in order to activate WiFi, select SSID
and enter the network key.
The recommended connection is via Ethernet. Static IP settings
is showed on the next page of this manual.
Hardware settings IP Address Settings
Contact for further settings and troubleshooting
technical support at: [e-mail]
If you are interested, you can sign up for training
or watch tutorial videos on the YouTube channel
SAFECONTROL.
Configuration
SAFE SER VER ADRESS
LEA VE CONFIGUR AT ION MENU
Server address
MAC address
Server Unavailabl
Server Unavailabl
e
TR
Y RECONNECT NOW
5x