Sahara CLEVERBOARD 3 User manual

CLEVERBOARD 3 with LYNX 4
QUICK START GUIDE

LOADING DRIVER SOFTWARE
• Place the Clever
p
roducts disk
(
su
pp
lied with
y
our board
)
p(ppy)
into your computer.
• From the screen that automatically opens up on screen
select
“
Cleverboard 3
-
GO
”
(this is the driver). Do
NOT
select
Cleverboard
3
GO
(this
is
the
driver).
Do
NOT
have the computer connected to the board at this time.
• Follow the on screen instructions until “Finish” is
displayed
displayed
.
• Now connect your computer to the board via the USB
cable (supplied).
•
A
new USB device will be detected, Continue to load the
second part of the driver until “Finish” is once again
dis
p
la
y
ed.
py

LOADING LYNX SOFTWARE
• From the same disk su
pp
lied with the board now
pp
select “Lynx” “GO” and follow the on-screen
instructions.
D i h i ll i ill b k d
•
D
ur
i
ng t
h
e
i
nsta
ll
at
i
on you w
ill
b
e as
k
e
d
to type
in two sets of licence codes, one for Lynx and
one for Wordwall these can be found on the
one
for
Wordwall
,
these
can
be
found
on
the
reverse side of the disk case.
• Note the red “cross” will not change to a green
“tick” until all of the code has been entered
correctly.

SET UP
•Should look something like this
• Computer to board via USB cable
•Com
p
uter to
p
ro
j
ector via VGA cable
ppj
• Image positioned on board

GETTING STARTED
• Check that the batteries in
y
our
p
en are live b
y
yp y
pressing on the pen nib whilst holding the pen to
your ear and listening for a high pitched “buzzing
sound
”
sound
• Ensure that the left hand door is in the open
position as this is the
“
receiver device
”
which will
position
as
this
is
the
receiver
device
which
will
not see the signal from the pen (transmitter) if
closed.
• If you are using the Ink Capture mode refer to
the Ink Capture document for the use of this
facility
facility
.

CALIBRATION
•
At the computer refer to the taskbar at the
At
the
computer
refer
to
the
taskbar
at
the
bottom of your screen locate the
“Cleverdriver” Icon.
• Right Click on the “Cleverdriver” Icon.
•
Select
“
Settings
”
Select
Settings
• Ensure that the word “Interactive” is
selected from the next box that will appear
selected
from
the
next
box
that
will
appear
on screen,
•
Select
“
Calibrate
”
Select
Calibrate

CALIBRATION CONTINUED
Ensure a “Tick” is
p
laced
p
in the “use previous
calibration” box.

CALIBRATION CONTINUED
• Once “Calibrate” has been selected the screen will
change to a white background with a “cross” inside a
“circle” in the left hand corner.
•
Take the interactive pen and press with the nib in exactly
Take
the
interactive
pen
and
press
with
the
nib
in
exactly
the centre of the cross.
• Chase the “crosses” around the screen pressing with the
pen nib on each one (9 in total) Be accurate and take
pen
nib
on
each
one
(9
in
total)
.
Be
accurate
and
take
your time.
• Once the last cross has been selected the screen will
h b k t “ l d i tti ” b d
c
h
ange
b
ac
k
t
o
“
c
l
ever
d
r
i
ver se
tti
ngs
”
b
ox an
d
you
should tick “OK”.
• The board is now calibrated.

LYNX 4 Software
•
Double click on the Lynx 4 Icon.
Double
click
on
the
Lynx
4
Icon.
•
This will take you into
“
Workbook
”
mode
•
This
will
take
you
into
Workbook
mode
YL kbkhldlk
•
Y
our
L
ynx wor
kb
oo
k
s
h
ou
ld
l
oo
k
like………………………………(next page)

LYNX 4 Software