Salto RF Node User manual

All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any
item in this catalog, its design, construction, and/or materials.
221136 -ED0 - 10/09/ 2012
©2012 SALTO Syst ems S.L. 1/3
RF Node
Installation guide RF Node
Guía de instalación RF Node
Electrical characteristic
Características Eléctricas
Description
The RF Node is part of SALTO´s RF2 system. It works as a bridge, with the Gatewayx2,
between SALTO´s access control software and RF locks.
Descripción
El RF Node forma parte del sistema RF2 de SALTO Systems. Actúa como puente, junto
con el Gatewayx2, entre el software de control de acceso de SALTO y las cerraduras RF.
Mechanical Installation
Instalación Mecánica
Operaon condions
Min Typ Max Unit
Temperature -20 25 70 ºC
Humidity 35 85 %
Note 1: 1x2x24AWG or UTP CAT5e recommended
Note 2: Power supply must be calculated taking into account Gatewayx2 and
Nodes current consumpon
2405-2480 Mhz
IEEE 802.15.4
RF Characteriscs
Frequency Range
Standard
10/15mIndoor Radio Range
7 12 28 V
mA45
Power Supply
Imput Voltage
Current consumpon
Min Typ Max Unit
Note 2
Cable requirements
RS485 Connecon (AB)
Generic twisted pair wire
Power Connecon (Vdd)
24 AWG
Note 1
SALTO´s Software
*RS485 Bus
*Power Supply
UTP CAT5e
*RS485 Bus
*Power Supply
UTP CAT5e
Up to 6 External RF Node
per Gatewayx2
RF Node RF Node
Up to 112 SALTO RF Lock per
Gatewayx2 (16 per RF Node)
Power
RS485 bus to Nodes
Up to 10/15m
to Node
RF Link
83
83
20 Gatewayx2
[25/32”]
[3-1/4”]
[3-1/4”]

All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any
item in this catalog, its design, construction, and/or materials.
221136 -ED0 - 10/09/ 2012
©2012 SALTO Syst ems S.L. 2/3
Electrical Installation
Instalación Eléctrica
Installation guide RF Node
Guía de instalación RF Node
Installation Example
Ejemplo de Instalación
RS485 bus termination resistor is
needed (ON position) when the
node is located at the end of the bus.
La resistencia de terminación de l bus
RS485 es necesaria (posición ON)
cuando el equipo esté situado en uno
de los extremos del bus.
Gatewayx2
Up to 10/15m
to Node
RF Link
RF Node RF Node RF Node RF Node RF Node RF Node
UTP CAT5e
1pair RS485
1pair 12v Power
50m
UTP CAT5e
1pair RS485
1pair 12v Power 25m
CLR
V+
A
B
ON
R
OFF
V+ A B
RS485 Bus
Termination

All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any
item in this catalog, its design, construction, and/or materials.
221136 -ED0 - 10/09/ 2012
©2012 SALTO Syst ems S.L. 3/3
Señalización
Señalización
Installation guide RF Node
Guía de instalación RF Node
The Green LED of the Node indicates that the Node is properly powered.
El LED en verde indica que el Nodo está alimentado correctamente.
Operational test
Test Operacional
Once the product is installed, follow these steps to check the correct operation:
- When Gatewayx2 and locks are installed, check that the RF Node is active in SALTO´s
software.
Una vez instalada la unidad de control, para comprobar el correcto funcionamiento de
la instalación, siga los siguientes pasos:
- Comprobar que al instalar el Gatewayx2 y las cerraduras el nodo está activo en el
software de SALTO.
This unit should be tested at least once a year as described in “Operational
Test”.
Es recomendable realizar un testeo operacional una vez al año siguiendo
el “Test Operacional”.
Declaration of Conformity
Declaración de conformidad
Maintenance
Mantenimiento
Salto Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun– Spain) declares herewith under its sole responsibility that the product: RF Node
complies with the requirements of the directive 89/336/EEC (Electromagnetic Compatibility) and the modifications gathered under the directive 93/68/EEC. You
will be able to find a copy of the original declaration of conformity at the following Internet address: http://www.saltosystems.com
Salto Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun– Spain) declara bajo su responsabilidad que el producto: RF Node cumple con los
requerimientos de la directiva 89/336/EEC (Compatibilidad Electromagnética) y sus modificaciones recogidas en la directiva 93/68/EEC. Podrá encontrar una
copia de la declaración de conformidad original en la siguiente dirección de internet: http://www.saltosystems.com