Saluki S3302 Series User manual

S3302 Series Spectrum Analyzer
Quick Start Guide
Saluki Technology Inc.

Tel: [phone] Email: [email protected]
www.salukitec.com
1
!
WARNING
A “WARNING” sign indicates for an existing danger. It reminds the user to pay
attention to a certain operation process, operation method or the similar. Any
violation against the indicated rules or incorrect operation may lead to personal
injury. It is not allowed to proceed until the warning conditions are fully
comprehended and satisfied.
Preface
Thanks for choosing S3302 series spectrum analyzer produced by Saluki Technology Inc. Please read this quick
guide carefully for your convenience.
We devote ourselves to meeting your demands, providing you high-quality measuring instrument and the best
after-sales service. We persist with “superior quality and considerate service”, and are committed to offering
satisfactory products and service for our clients.
Manual No.
S3302-04-01
Version
Rev01 2019.05
Saluki Technology
Manual Authorization
The information contained in this Quick Start Guide is subject to change without notice. The power to interpret the
contents of and terms used in this guide rests with Saluki.
Saluki Tech owns the copyright of this document which should not be modified or tampered by any organization or
individual, or reproduced or transmitted for the purpose of making profit without its prior permission, otherwise
Saluki will reserve the right to investigate and affix legal liability of infringement.
Product Quality Certificate
The product meets the indicator requirements of the manual at the time of delivery. Calibration and measurement are
completed by the measuring organization with qualifications specified by the state, and relevant data are provided for
reference.
Quality/Environment Management
Research, development, manufacturing and testing of the product comply with the requirements of the quality and
environmental management system.
Precautions
For the purpose of this manual, the following safety symbols apply, and please be familiar with them and their
meanings before operating this instrument!

Tel: [phone] Email: [email protected]
www.salukitec.com
2
A “CAUTION” sign provides prompt on important information but not dangerous
situations. It reminds the user to pay attention to a certain operation process, operation
method or the similar. Any violation against the indicated rules or incorrect operation
may lead to instrument damage or loss of important data. It is not allowed to proceed
until the cautioning conditions are fully comprehended and satisfied.
CAUTION
Contacts
Service Tel:
886.909 602 109
Website:
www.salukitec.com
Email:
[e-mail]
Address:
No. 367 Fuxing N Road, Taipei 105, Taiwan (R.O.C.)

Tel: [phone] Email: [email protected]
www.salukitec.com
3
CONTENTS
Chapter 1 Manual Overview......................................................................................................................................... 5
Chapter 2 Ready for Use................................................................................................................................................ 6
2.1 Preparation before Operation...................................................................................................................................6
2.1.1 Environmental requirements.........................................................................................................................6
2.1.2 Power supply requirements............................................................................................................................6
2.1.3 Electrostatic discharge (ESD) protection......................................................................................................7
2.2 Description of Start for Use.....................................................................................................................................8
2.3 Front Panel Overview.............................................................................................................................................. 8
2.3.1 Power key and indicator................................................................................................................................8
2.3.2 Function key zone......................................................................................................................................... 9
2.3.3 Preset key...................................................................................................................................................... 9
2.3.4 Photosensitive hole....................................................................................................................................... 9
2.3.5 Numeric keypad............................................................................................................................................ 9
2.3.6 Loudspeaker................................................................................................................................................ 10
2.3.6 Label display area....................................................................................................................................... 10
2.4 Operation Interface Overview............................................................................................................................... 10
2.5 Top Panel Overview...............................................................................................................................................10
2.5.1 Power interface............................................................................................................................................11
2.5.2 Test ports..................................................................................................................................................... 11
2.5.3 Digital interfaces......................................................................................................................................... 11
2.5.4 Device symbols........................................................................................................................................... 12
2.6 Battery Installation or Replacement...................................................................................................................... 12
Chapter 3 Typical Application.....................................................................................................................................14
3.1 Basic Signal Measurement.................................................................................................................................... 14
3.2 How to Improve the Accuracy of Frequency Measurement................................................................................. 17
3.3 How to Measure Small Signals............................................................................................................................. 18
3.3.1 Reduce RF attenuation decrement to measure small signals......................................................................18

Tel: [phone] Email: [email protected]
www.salukitec.com
4
3.3.2 Reduce resolution bandwidth to measure small signals............................................................................. 20
3.3.3 Measuring small signals by using average detection and increasing sweep time......................................21
3.3.4 Measuring small signals by using video average....................................................................................... 22
3.4 How to Identify Signal with Closely Spaced Frequency...................................................................................... 23
3.4.1 Description of resolution bandwidth.......................................................................................................... 23
3.4.2 Measurement for distinguish two signals with same amplitude.................................................................23
Chapter 4 Getting Help................................................................................................................................................ 26
4.1 Basic Inspection.....................................................................................................................................................26
4.2 Help Information....................................................................................................................................................26
4.3 Repair Methods......................................................................................................................................................27
Appendix 1 Technical Specifications...........................................................................................................................28
Appendix 2 List of Accessories/ Options.................................................................................................................... 31

Tel: [phone] Email: [email protected]
www.salukitec.com
5
Chapter 1 Manual Overview
This manual describes the structure and use of the S3302 series spectrum analyzer (hereinafter referred to as
S3302 or the spectrum analyzer) in an all-around and three- dimensional manner from aspects of instrument panel,
power supply, start to use, typical applications and after-sales help. By reading this Manual, you will have an
overall understanding of S3302 and quickly master the basic operations of this device in a systematic manner. For
the convenience of operation, please carefully read the manual before operating the instrument, and properly
operating it according to the guidance in the manual.
S3302 Series Spectrum Analyzer Quick Start Guide includes the following chapters and sections:
Preparation for Use
This chapter introduces S3302 preparation before use, start to use, panel introduction and battery replacement. By
reading this chapter, you will gain the perceptual knowledge of S3302 as a whole and make preliminary
preparations for correct and safe operation of this device.
Typical Applications
This chapter explains basic measurement methods of S3302 and operating steps of basic measurement functions in
details through test instances on how to distinguish closely spaced signals, how to improve frequency
measurement accuracy and how to measure small signals. In addition, this chapter also briefly describes the skills
used in tests. By reading this chapter, you can use S3302 to complete certain typical tests independently.
Getting Help
This chapter consists of after-sales repair and its procedures with the emphasis on problem solving, maintenance
and repair of this device during use.

Tel: [phone] Email: [email protected]
www.salukitec.com
6
!
WARNING
To prevent damage to the instrument and avoid electric shock, fire and personal
injury:
Do not open this device without authorization;
Do not disassemble or modify any part which is not described in this manual.
Any disassembly without authorization may result in reduction of
electromagnetic shielding performance or damage to the parts inside the device,
thus comprising product reliability. We shall not offer free repair service to any
product which is disassembled without authorization even if the product is still
within warranty period.
Chapter 2 Ready for Use
The S3302 series spectrum analyzer is characterized by wide operating frequency band, high performance index,
fast sweeping, multiple test functions and easy operation. In terms of performance index, this series has good
average noise level, phase noise, fast sweep speed and multiple measurement functions. Adopting the 8.4-inch
integrated liquid crystal and capacitive touchscreen and portable structure with small volume and light weight, this
series features flexible power supply and is particularly suitable for field use. This chapter emphatically introduces
the test environment, power supply, structure and battery replacement of this device.
2.1 Preparation before Operation
This section describes the precautions before initial use of the S3302 series spectrum analyzer. S3302 meet the
safety requirements of GJB3947A-2009. Please read the following safety instructions carefully so as not to cause
damage to the instrument or unintentional personal injury.
2.1.1 Environmental requirements
To ensure long service life and effective and accurate measurement of the S3302 series instrument, test it under the
following environmental conditions:
1. Temperature range:
Storage temperature range: -40℃to +70℃
Operating temperature range: -10℃to +50℃
Operating temperature range of power supply by Li-ion battery: -10℃to +50℃
!
WARNING
As the battery storage temperature range is -20℃to +60℃, the battery must not work
continuously in a long time at high temperature, so as to avoid risks arising from high
temperature. It is recommended to use the adapter to supply power.
2. Low atmospheric pressure:
Low atmospheric pressure (altitude): 0 - 4,600m
2.1.2 Power supply requirements
Three power supply forms are supported by S3302:

Tel: [phone] Email: [email protected]
www.salukitec.com
7
1. AC power supply and power supply with adapter
The accompanying AC-DC adapter must be used for AC power supply. The input power supply of the adapter
is 100~240V, 50/60Hz AC.
When transported and carried in a backpack, please do not connect the AC-DC adapter to the device to
avoided overheating. The AC-DC adapter has a wide range of voltage input. When in use, please make sure
the power supply voltage is within the scope specified in Table 2.1.
Table 2.1 Power supply requirements
Power supply parameter
Applicable range
Input voltage
Rated input currency
Work frequency
Output Voltage/Current
100V - 240VAC
1.7A
50/60Hz
15.0V/4.0A
CAUTION
The working voltage and frequency ranges are subject to the parameters provided on the
nameplate of the power adapter.
2. DC power supply
Voltage: 15V
Current: 3A (min.)
3. Power supply with built-in battery
S3302 can be powered by rechargeable li-ion battery. The battery will discharge if it is not used for a long time.
Therefore, the battery must be recharged before use. Please refer to Section 2.6 for details about battery use. Basic
parameters of accompanying battery are as follows:
Nominal voltage: 10.8V
Nominal capacity: 7,800mAh
CAUTION
The rechargeable battery must not be exposed to fire or high-temperature environments
(above 70℃), or placed in fresh water or salt water, or made wet. It must be kept away from
children.
The rechargeable battery is reusable and should be stored in proper container to avoid
short circuit. Heavy metals such as nickel and chromium in the battery can pollute natural
environment. Waste battery shall not be discarded but shall be put into a special battery
recycle box.
2.1.3 Electrostatic discharge (ESD) protection
Electrostatic discharge is extremely destructive to electronic components and equipment, so the powered
instrument must be operated on a workbench with ESD protection. So please pay attention to ensuring ESD
protection when using the instrument. The following ESD protection measures can be taken if conditions are met:
1. Before connecting the cable to the instrument for testing, be sure to ground the center conductor of the cable
first. The following steps can be used: Connect a short-circuiter at one end of the cable to short the center

Tel: [phone] Email: [email protected]
www.salukitec.com
8
conductor and outer conductor of the cable. Wearing wrist straps with ESD protection, grasp the cable connector
housing, connect the other end of the cable, and then remove the short-circuiter.
2. The operator should be grounded before cleaning or checking the test port of the device or connection. This can
be realized by holding on to the metal casing of grounded device or the casing of test cable connector.
2.2 Description of Start for Use
Check the power supply unit based on the “power supply requirements” in Section 2.1.2 before powering on the
S3302. Power on for testing after no problem is found.
Press the POWER key [ ] on the front panel for more than 3s, a beep can be heard. Then, release the ON/OFF
key and the device will enter host program after about 30 seconds. To ensure the stability of performance indexes
of parts inside the device in order to achieve better test results, a 30-minute warming period is recommended
before measurement..
2.3 Front Panel Overview
The front panel of the S3302 series spectrum analyzer is as shown in Fig. 2.1.
Fig.2.1 Front panel of S3302 series spectrum analyzer
2.3.1 Power key and indicator
Power key and the indicator are located at the lower left of the front panel. The power indicator is inside the
yellow power key. The indicator for power off is yellow and that for power on is green. The correlation between
color of the indicator and physical status of the device is shown in the Table2.2.

Tel: [phone] Email: [email protected]
www.salukitec.com
9
Table 2.2 Description of indicator status
Instrument
status
Indicator status
Physical status of the Spectrum Analyzer
Power off
Off
battery installed, power not connected.
battery not installed, power not connected.
Yellow normally on
a) battery not installed, power connected.
b) battery installed and full, power connected.
Yellow flickering
Battery installed but not full, power connected.
Power on
Status
Green normally on
a) battery not installed, power connected.
b) battery installed and full, power connected.
c) battery installed, power not connected.
Green flickering
Battery installed but not full, power connected.
2.3.2 Function key zone
Commonly-used functional keys are described as follows:
【Freq】: Set the scope of frequency measured, frequency step, signal standard, etc.
【Ampt 】: Set the amplitude of measurement results displayed, including display format, display
scale and control of pre-amplifier.
【BW 】: Set the resolution bandwidth, video bandwidth, detector type, average value and other
measurement parameters.
【Marker 】: Enable function menu related to the marker. When enabled, the marker can be operated
by dragging, clicking or other touch modes.
【Peak】: Enable the peak search function.
【Mode】: Select the operating mode of the device, including spectrum analyzer, interference analyzer,
AM-FM-PM analyzer, power meter, channel scanner and other modes.
2.3.3 Preset key
Preset or reboot the system to restore to default initial state. Preset can be realized by pressing and releasing this
key.
2.3.4 Photosensitive hole
This hole can sense the intensity of external light for auto adjustment of liquid crystal brightness.
2.3.5 Numeric keypad
Numeric keys: the value corresponding to the selected parameter can be input via the numeric keys on the
front panel, and the corresponding unit can be selected in the soft menu.
【•】: Input the decimal point for decimal value when entering a decimal value with a decimal point.
【+/-】: Positive/negative sign, before inputting a numerical value, you can use this key to input a positive or
negative value.
【↑】and 【↓】: Control the step upward and downward, or select the current item up and down.

Tel: [phone] Email: [email protected]
www.salukitec.com
10
【Cancel】: Used to exit any functional operation without changing the current parameter. Deactivate the
function, exit the digital zone operation, and exit the file dialog box.
【Backspace】: Remove a character before the marker in the input area.
【Enter】: In the case of an input area, press the key to receive data in accordance with the default unit.
Knob: Used to move the marker and change the current parameter value. It is generally used for fine tuning
of the parameters to optimum values.
2.3.6 Loudspeaker
The S3302 series spectrum analyzer is equipped with a speaker. Keep the speaker opening clean so as not to affect
sound effects.
2.3.6 Label display area
It shows the corresponding model, frequency range, label, and name of the S3302 series spectrum analyzer.
2.4 Operation Interface Overview
The S3302 series spectrum analyzer has an integrated 8.4-inch integrated liquid crystal and capacitive touch screen,
and the operation interface is shown in Fig.2.2.
Fig.2.2 Operation interface of S3302 series spectrum analyzer
2.5 Top Panel Overview
The top panel of S3302 is shown in Fig. 2.3 and it consists of a power interface, a digital interface and a test port.

Tel: [phone] Email: [email protected]
www.salukitec.com
11
Fig.2.3 Top Panel of S3302 Series Spectrum Analyzer
2.5.1 Power interface
The power interface of the device is for powering the device through DC output of AC-DC adapter or through
external DC power source. The conductor inside the external power interface is positive and the external
conductor is grounded.
2.5.2 Test ports
(1) RF input port: This port is for inputting tested signal. The test signal input port of S3302 is 50Ω. 4GHz,
6.5GHz, 9GHz, 20GHz and 26.5GHz models use N type female port and 32GHz and 44GHz models use 2.4mm
male port.
(2) RF output port: This port is for signal output. 50Ω impedance, N-type female port, provided only when
customers need the tracking generator option.
(3) 10MHz input/output port: This port is for connecting 10MHz signal of other devices as the reference signal
of the analyzer. It can also be used for outputting the internal 10MHz reference signal for other devices.
(4) IF output port: Under zero span, this port can be used for outputting the IF signals for other devices
through software configuration.
(5) Trigger input port: External trigger mode can be set for S3302. The scope of trigger source must be -5V to
+5V when connecting the external trigger source to the trigger input port of the Spectrum Analyzer. Rising edge
trigger or fall edge trigger can be set by the software.
(6) GPS antenna port: This port can be used for connecting GPS antenna device for locating current position of
the Spectrum Analyzer.
!
WARNING
In order to protect the spectrum analyzer, the instrument test ports are provided with
some signs. To use the spectrum analyzer, be sure to read these signs to avoid
permanent damage to the instrument.
For details of the instrument signs, see section 2.5.4.
2.5.3 Digital interfaces
(1) Mini USB interface: This interface is used for connecting external PC which realizes program control or
data transmission for S3302 through program control commands or function library.

Tel: [phone] Email: [email protected]
www.salukitec.com
12
CAUTION
Equipment drive should be installed for connecting the device to PC through USB
interface for the first time.
(2) A-type USB interface: This interface is used for connecting USB peripheral equipment, such as USB storage
device, USB power detector.
(3) LAN (network) port: This interface is a 10/100Mbps network interface through which a PC can be
connected to the device through a network cable. PC can realize program control or data transmission for S3302
through program control commands or function library.
(4) SD card slot: This Micro SD card slot can be used to extend the storage space of the device.
(5) Headset jack: This is a standard headset jack for 3.5mm/3 line for audio output of FM/AM/SSB
demodulation. When a headset is not connected to this jack, the audio output will be realized through the
loudspeaker of the device. When a headset is connected to this jack, audio output will be automatically switched
from the loudspeaker to the headset.
2.5.4 Device symbols
Device symbols indicated in the Fig. below indicate that the maximum power of RF IN and the maximum input
DC level. When the device is in operation, the user is not allowed to connect signal exceeding this range to the
port. Otherwise, the device may be destroyed.
2.6 Battery Installation or Replacement
S3302 accompanies with a large-capacity rechargeable Li-ion battery with a battery life of 2.5 hours. For field test
for long period, it is recommended to purchase a battery of same mode as a standby battery.
CAUTION
To guarantee the longer service life of the battery, the battery should be removed from
battery holder during the transportation and long-time storage, and try not to make the
battery power less than 5%, otherwise the battery may not be able to charge.
Installation or replacement of battery can be carried out by reference to Fig. 2.4 for battery installation or
replacement of S3302.

Tel: [phone] Email: [email protected]
www.salukitec.com
13
Fig. 2.4 Install or replace the battery

Tel: [phone] Email: [email protected]
www.salukitec.com
14
Chapter 3 Typical Application
The S3302 series spectrum analyzer provides several working modes, including spectrum analysis, interference
analyzer (option), AM-FM-PM analyzer (option), power meter (option) and channel scanner (option). Several
intelligent measurement functions are provided for each working mode. This chapter mainly describes basic tests
under spectrum analyzer mode. For detailed operation of each optional mode, please refer to the User Manual of
S3302 Spectrum Analyzer.
CAUTION
In this guide, the keys on the front panel are indicated in the form of 【XXX】, and
XXX is the name of the key; the bottom keys on the touch screen are indicated in the
form of 【XXX】, and XXX is the name of the key; the menu
buttons on the right are indicated in the form of [XXX], and XXX is the menu name.
3.1 Basic Signal Measurement
The basic measurement includes the frequency and amplitude of the signal marked on the spectrum analyzer
screen with markers. Follow the procedures below to measure the input signal and save the current measurement
result by using the file menu:
a) Set the center frequency
Set the frequency of the external signal generator to 1GHz. Set the center frequency of the spectrum analyzer.
Press 【Freq】, select [Center Freq] and set the center frequency to 1GHz. Enter 【1】[GHz] directly with the key
in the front panel data zone. These numerical keys can be used for setting the exact value of current parameter.
The value of center frequency can also be changed by the step key and knob, as shown in Fig. 3.1.
Fig. 3.1 Center Frequency of 1 GHz

Tel: [phone] Email: [email protected]
www.salukitec.com
15
b) Set the span
Press 【Freq】→[Span]. Please note if the span is shown in the active function area in order to confirm currently
activated parameter. To reduce the span to, for example, 10MHz, you can input [1] [0] using the numerical keypad
and select the unit as [MHz], or you can use 【↓】key to reduce to this value by step (the numerical keys and
step keys can be used for changing the value of current parameter). The result is shown in Fig. 3.2. Attention
should be paid to check if the resolution bandwidth and the video bandwidth are adaptable to the span as they will
be automatically adjusted to a proper value based on the given span value. The sweep time is also adaptable.
Fig. 3.2 Center Frequency of 1GHz and Span of 10MHz
c) Set the sweep time
Press 【Sweep】key and select [Sweep Time Auto Man] soft key. The soft key can be used to set auto or manual
control of the sweep time, and the currently active option is underlined. For example, when “Auto” is underlined,
the sweep time will be automatically adaptable to other relevant parameter settings.
d) Activate the marker
By pressing 【Marker】, common marker will be activated and displayed in the center of the horizontal coordinates
(the frequency and amplitude will be read by the marker and shown in the active function area). The marker reads
the frequency as 1GHz and amplitude as -20dBm, as shown in Fig. 3.3.
If the marker is not at the peak, you can press 【Peak】key to enable the marker to automatically jump to the peak
of the signal or use the knob on the front panel to manually position the marker on the maximum value of the
signal.

Tel: [phone] Email: [email protected]
www.salukitec.com
16
Fig. 3.3 Activating the Marker
e) Adjust the amplitude parameter
Generally, optimal amplitude measurement accuracy can be obtained by putting the signal peak at the reference
level position, as shown in Fig. 3.4. Press 【Ampt 】→[Ref Level] to set the reference level as the amplitude of
the marker.
Fig. 3.4 -20dBm Reference Level
f) Save the test results
Press 【File】→[Save Data] (or select the save state or picture) and an interface shown in Fig. 3.5 will pop up.

Tel: [phone] Email: [email protected]
www.salukitec.com
17
Input the name on the interface and then press [OK] to save.
Fig. 3.5 File Saving
3.2 How to Improve the Accuracy of Frequency Measurement
This section will take the measurement of external 1GHz signal as an instance to describe how to use the marker
count function to improve the frequency reading accuracy for measurement. The test steps are as follows:
a) Reset the spectrum analyzer
Press 【Preset】key to restart the spectrum analyzer.
b) Set the center frequency
Set the frequency of the external signal generator to 1GHz. Set the center frequency of the Spectrum Analyzer.
Press 【Freq】, select [Center Freq] and set the center frequency as 1GHz. Or you can directly input [1] [GHz]
using the keys in numerical keypad on the front panel. These numerical keys can be used for setting the exact
value of current parameter. The value of center frequency can also be changed by the step key and knob.
c) Enable the marker count function
Press 【Marker】to activate the marker. Press 【Marker】→[Counter Mkr Off On] to enable the marker count
function. Press 【Peak 】to position the marker on the signal frequency. Observe the reading of the marker and
the resolution of frequency can reach 1Hz. As shown in Fig.3.6.

Tel: [phone] Email: [email protected]
www.salukitec.com
18
Fig. 3.6 Improving the Accuracy of Frequency Measurement by Using Marker Function
The marker counting function can be only used to measure continuous wave signals or discrete spectrum
components that their amplitudes are greater than -50dBm and such amplitudes must be 30dB higher than noise
levels.
d) Disable the marker counter function
Press 【Marker】→[Counter Mkr Off On] to disable the marker count function.
CAUTION
When executing frequency count function, if the sweep speed of the Spectrum Analyzer
slows down, this is normal as the Spectrum Analyzer is taking some time for accurate
positioning of signal and IF count in the background!
CAUTION
When executing frequency count function, to accurately measure the frequency, the tested
signal generator should share the same time base with the Spectrum Analyzer!
3.3 How to Measure Small Signals
The noise generated inside the spectrum analyzer determines its ability to measure small signals. The following
methods can be used to change the measurement setting, thus improving the measurement sensitivity of the
Spectrum Analyzer.
3.3.1 Reduce RF attenuation decrement to measure small signals
The input attenuator affects the signal level of the input instrument. If the input signal is very close to the
noise base, by reducing the decrement of the attenuator, the signal can be extracted from the noise.
CAUTION
The total power of all signals input to the spectrum analyzer shall be less than +30dBm
(1W).

Tel: [phone] Email: [email protected]
www.salukitec.com
19
a) Reset the spectrum analyzer
Press 【Preset】key to restart the spectrum analyzer.
b) Set the center frequency, the span, and the reference level
Set the frequency of the external signal generator to 300MHz and set the amplitude to -80dBm, and connect the
radio frequency output end of the signal generator to the radio frequency input end of the spectrum analyzer. Set
the center frequency of the spectrum analyzer. Press 【Freq 】and select [Center Freq] to set the center
frequency to 300MHz, and then select 【Span】to set the span to 5MHz. Press 【Ampt】and select [Ref Level]
to set the reference level to -40dBm.
c) Move the signal peak to the center frequency (300MHz in this case)
Press 【Peak】and [Marker→Center] to move the signal peak to the center frequency.
d) Reduce bandwidth
Press 【BW】and set the bandwidth as 1MHz. If necessary, repeat Step c) to ensure that the signal peak is the
center frequency of the Spectrum Analyzer. As shown in Fig. 3.7.
Fig. 3.7 Small Signals when pre-amplifier Off
e) Enable the pre-amplifier
On this basis, you can further enable the pre-amplifier by pressing 【Ampt 】→[Pre Amp Off On], as shown in
Fig. 3.8.