SALZ SWITCH 2008TX User manual

SWITCH 2008TX
Quick Installation Guide
-1- -2- -3-
1. Overview
SWITCH 2008TX Unmanaged Industrial Ethernet Switch is
specially designed to expand reliable Ethernet connectivity to
factory oors and outdoor environments with extreme
temperature and climatic conditions.
SWITCH 2008TX is equipped with 8 x 10/100 RJ45 Ports
enclosed in IP30 housing.
4. Grounding the switch SWITCH 2008TX
!
ATTENTION:
This product is intended to be mounted to a well-
grounded mounting surface such as a metal panel.
!
WARNING:
Safety measures should be taken before connecting
the power cable.Turn o the power before connecting
modules or wires. The correct power supply voltage is listed on
the product label. Check the voltage of your power source to
make sure that you are using the correct voltage. DO NOT use a
voltage greater than what is specied on the product label.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size. If current
exceeds the maximum rating, the wiring can overheat causing
serious damage to your equipment.
Please read and follow these guidelines:
• Use separate paths to route wiring for power and devices. If
power wiring and device wiring paths must cross make sure
the wires are perpendicular at the intersection point
NOTE: Do not run signal or communications wiring and power
wiring through the same wire conduit. To avoid interference,
wires with dierent signal characteristics should be routed
separately
• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of
thumb is that wiring that shares similar electrical characteris-
tics can be bundled together
• You should separate input wiring from output wiring
• We advise that you label the wiring to all devices in the system
Removing the SwitchMounting the Switch
Clic k
Dismounting the switch
Press the switch from top and pull out the lower edge of the
switch and then remove the switch from the DIN rail.
Mounting the switch
Place the SWITCH 2008TX on the DIN rail from above using the
slot, push the front of the switch toward the mounting surface
until it snaps into place with a click sound.
Grounding and wire routing help limit the eects of noise due to
electromagnetic interference (EMI).
Step 1: Run the ground connection from the ground screw to
the grounding surface prior to connecting devices.
Step 2: Connect the ground connection from the terminal block
to the grounding surface prior to connecting device.
5. Wiring requirements
5.1 Wiring Power Input
SWITCH 2008TX with 2pin terminal block
!
Caution:
• Use copper conductors only
• Wiring cable temperature should support at
least 105˚C
• Tighten the wire to a torque value 20N
• The wire gauge for the terminal block should
range between 0.2 to 2.5 mm2
-
2. Package Checklist
• SWITCH 2008TX Switch x 1
• Quick Installation Guide x 1
3. Mounting and Dismounting to DIN-Rail
!ATTENTION:
The SWITCH 2008TX ia an open type device and
SWITCH 2008TX shall be DIN-Rail mounted or wall
mounted (optional) in cabinet or enclosure and the
ambient temperature should not exceed 75°C.
Panel view
Top View
Front View
Grounding Screw
DIN-Rail
Grounding
Screw
Power Input
Terminal Block
7
5
3
8
6
4
100Mbp
LNK/ACT
1 2
PWR
PWR
100M
LNK/ACT
+
PWR
12~48VDC
You can use “PWR” for Power input
Top view of Terminal Block is shown
in the gure below:
Terminal Block

-4- -5- -6-
To insert power wire and connect the 12 to 48 V DC at a
maximum of 0.2 A DC power to the power terminal block, follow
the steps below:
• Use at-head screw driver to loosen the wire-clamp screws
• Insert the negative/positive DC wires into the PWR-/PWR+
terminals, respectively
• Tighten the wire-clamp screws to prevent the wires from loosen-
ing
!
ATTENTION:
Please use a power supply from 12~48VDC, the device
power shall be supplied by 61010-2-201 R/C power
with SELV, Limited energy output.
!ATTENTION:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received
including interference that may cause undesired
operation
!ATTENTION:
If the equipment is used in a manner not specied by
SALZ Automation, the protection provided by the
equipment may be impaired.
Connect one end of an Ethernet/RJ45 cable into Ethernet port
of SWITCH 2008TX and other end to attached networking
device.
• Ports 1-8 of the switch support Fast Ethernet
(10/100Base-T RJ45 Ports)
• All the RJ45 ports on the SWITCH 2008TX support auto
negotiation and auto MDI/MDI-X to eliminate the need for
crossover cabling
5.1.2 Cabling RJ45
Operating Temperature
-40˚C ... 75˚C
Storage Temperature -40˚C ... 85˚C
Altitude Up to 2000m
Ambient relative humidity 5 to 95% (non-condensing)
7. Environmental limits
6. LED Indicators
PWR
(Green)
Power On by terminal block PWR
Terminal block PWR fails or is not available
100
(Green)
Link speed at 100 Mbps
Data is transmitting / receiving
Link speed at 10 Mbps or no link
Copper port link-up
Data is transmitting / receiving
No link or link failed
Illuminated
Illuminated
LNK/ACT
(Green)
O
Blinking
O
Illuminated
Blinking
O
Address of the manufacturer:
SALZ Automation GmbH
32105 Bad Salzuen, Germany
Email: [email protected]
v0.1
6400-000xxx
Note: Category 5e cable or above should be used.