SALZ 2016GT-E User manual
SWITCH 2016GT-E
Quick Installation Guide
-1- -2- -3-
1. Overview
SWITCH 2016GT-E Unmanaged Industrial Ethernet Switch is
specially designed to expand reliable Ethernet connectivity to
factory oors and outdoor environments with extreme
temperature and climatic conditions.
SWITCH 2016GT-E is equipped with 16 x 10/100/1000 RJ45
Ports enclosed in IP30 housing.
4. Grounding the switch SWITCH 2016GT-E
!
ATTENTION:
This product is intended to be mounted to a well-
grounded mounting surface such as a metal panel.
!
WARNING:
Safety measures should be taken before connecting
the power cable.Turn o the power before connecting
modules or wires. The correct power supply voltage is listed on
the product label. Check the voltage of your power source to
make sure that you are using the correct voltage. DO NOT use a
voltage greater than what is specied on the product label.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size. If current
exceeds the maximum rating, the wiring can overheat causing
serious damage to your equipment.
Please read and follow these guidelines:
• Use separate paths to route wiring for power and devices. If
power wiring and device wiring paths must cross make sure
the wires are perpendicular at the intersection point
NOTE: Do not run signal or communications wiring and power
wiring through the same wire conduit. To avoid interference,
wires with dierent signal characteristics should be routed
separately
• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of
thumb is that wiring that shares similar electrical characteris-
tics can be bundled together
• You should separate input wiring from output wiring
• We advise that you label the wiring to all devices in the system
Dismounting the switch
Press the switch from top and pull out the lower edge of the
switch and then remove the switch from the DIN rail.
Mounting the switch
Place the SWITCH 2016GT-E on the DIN rail from above using
the slot, push the front of the switch toward the mounting
surface until it snaps into place with a click sound.
Grounding and wire routing help limit the eects of noise due to
electromagnetic interference (EMI).
Run the ground connection from the ground screw to
the grounding surface prior to connecting devices.
5. Wiring requirements
5.1 Wiring Power Input
5.1.1 SWITCH 2016GT-E with 2pin terminal block
!
Caution:
• Use copper conductors only
• Wiring cable temperature should support at
least 105˚C
• Tighten the wire to a torque value 20N
• The wire gauge for the terminal block should
range between 0.2 to 2.5 mm2
-
2. Package Checklist
• SWITCH 2016GT-E Switch x 1
3. Mounting and Dismounting to DIN-Rail
!ATTENTION:
The SWITCH 2016GT-E ia an open type device and
SWITCH 2016GT-E shall be DIN-Rail mounted or wall
mounted (optional) in cabinet or enclosure and the
ambient temperature should not exceed 75°C.
Panel view
Top View
7
5
3
8
9 10
11 12
13 14
15 16
6
4
Front View
1 2
PWR
1000M
LNK/
ACT
1000Mbps
LNK/ACT
DIN-Rail
Grounding Screw
Removing the SwitchMounting the Switch
Click
PWR
Grounding
Screw
Power Input
Terminal Block
Reset
12~48VDC
PWR
+
You can use “PWR” for Power input
Top view of Terminal Block is shown
in the gure below:
Terminal Block
-4- -5- -6-
To insert power wire and connect the 12 to 48 V DC at a
maximum of 1.5 A DC power to the power terminal block, follow
the steps below:
• Use at-head screw driver to loosen the wire-clamp screws
• Insert the negative/positive DC wires into the PWR-/PWR+
terminals, respectively
• Tighten the wire-clamp screws to prevent the wires from loosen-
ing
!ATTENTION:
Please use a power supply from 12 to 48 V DC, the
device power shall be supplied by 61010-2-201 R/C
power with SELV, Limited energy output. !ATTENTION:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received
including interference that may cause undesired
operation
!ATTENTION:
If the equipment is used in a manner not specied by
SALZ Automation, the protection provided by the
equipment may be impaired.
Connect one end of an Ethernet/RJ45 cable into Ethernet port
of SWITCH 2016GT-E and other end to attached networking
device.
• Ports 1-16 of the switch support Fast Ethernet as well as
Gigabit Ethernet (10/100/1000Base-T RJ45 Ports)
• All the RJ45 ports on the SWITCH 2016GT-E support auto
negotiation and auto MDI/MDI-X to eliminate the need for
crossover cabling
5.2 Cabling RJ45
Address of the manufacturer:
SALZ Automation GmbH
Max-Planck-Str. 64
32107 Bad Salzuen, Germany
Email: [email protected]
Please scan for more information:
v0.2
Note: Category 5e cable or above should be used.
Operating Temperature
-40˚C ... 75˚C
Storage Temperature
-40˚C ... 85˚C
Altitude
Up to 2000m
Ambient relative humidity
5 to 95% (non-condensing)
UL61010
Indoor use and pollution degree 2
7. Environmental limits
6. LED Indicators
PWR
(Green)
Power On by terminal block PWR or
DC-Jack
Terminal block PWR/DC-Jack fails or
is not available
LNK/ACT
(Green)
Copper port link-up 1000Mbps
Data is transmitting / receiving
Port disconnected or link failed
Illuminated
1000M
(Green)
O
Illuminated
O
Illuminated
Blinking
O
Link speed at 10/100Mbps
Link speed at 1000Mbps
Other SALZ Switch manuals
