Samcon RoughCam niteZoom User manual

RoughCam®niteZoom
User manual

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 2 of 20
Content
1Technical Data..........................................................................................................4
1.1 Electrical parameters...........................................................................................4
1.2 System cable SKAxx...........................................................................................4
1.3 Mechanical parameters.......................................................................................4
1.4 Temperature range..............................................................................................5
1.5 Sensor.................................................................................................................5
1.6 Lens ....................................................................................................................5
1.7 Electronical functions ..........................................................................................5
2Safety guidelines......................................................................................................6
3Illustration of the model key....................................................................................6
4Commissioning ........................................................................................................7
4.1 Step 1: Installation...............................................................................................7
4.2 Step 2: Electrical connection...............................................................................7
4.2.1 Potential equalization.................................................................................................................8
4.2.2 Termination of the connection cable (pigtail).............................................................................8
4.2.3 Power supply & protection.......................................................................................................10
4.2.4 Power supply & protection of the camera’s power circuit ........................................................10
4.2.4.1 Power supply & protection of the heating’s power circuit (optional) ..............................................10
4.2.5 Video picture connection (CVBS)............................................................................................11
4.2.6 Control interface (RS-422).......................................................................................................11
4.2.7 Tests prior to switching on voltage ..........................................................................................12
4.3 Step 3: Adjusting the picture .............................................................................12
4.3.1 Work preparation .....................................................................................................................15
4.3.2 Opening the housing................................................................................................................15
5Maintenance / Servicing.........................................................................................16
6Disposal / Recycling ..............................................................................................16
7Drawings.................................................................................................................17
8Notes .......................................................................................................................18

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 3 of 20
Table of figures
Figure 4.1 Potential equalization T10-VA….......................................................................8
Figure 4.2 RoughCam niteZoom –T10-VA-B-XXX-K-N....................................................8
Figure 4.3 RoughCam niteZoom –T10-VA-B-XXX-K-L.....................................................9
Figure 4.4 RoughCam niteZoom –T10-VA-B-XXX-P-N....................................................9
Figure 4.5 RoughCam niteZoom –T10-VA-B-XXX-P-L.....................................................9
Figure 4.6 Setting the Baud-transmission rate.................................................................12
Figure 4.7 FCB Control Panel of the RoughCam niteZoom.............................................13
Figure 4.8 Control and visualization via a video server ...................................................13
Figure 4.9 RoughCam®niteZoom –lens and sensor board ............................................14
Figure 7.1 T10-VA-K1......................................................................................................17
Figure 7.2 T10-VA-K2......................................................................................................17
Revision history
Product: RoughCam® niteZoom
Title: User manual for the RoughCam®niteZoom
Doc. -Id. 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00
Author: H. Helland
Date: August 16, 2018
Rev.- Index
Date
Name
Remarks
Authorization
00
16.08.2018
H. Helland
Compilation of the document
Based on the document 131106-
PT03BA-SS-ExCam nite-
Zoom_en_rev.01
Digital unterschrieben von Steffen
Seibert
DN: cn=Steffen Seibert,
o=SAMCON, ou,
[email protected], c=DE
Datum: 2019.06.24 12:02:44 +02'00'

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 4 of 20
1 Technical Data
1.1 Electrical parameters
Camera:
Supply voltage: +12 V DC to +30 V DC
Reference power: +24 V DC
Power input: 270 mA to 540 mA
Maximum power input: 6.5 W (without heating)
Heating (optional):
Supply voltage: +12 V DC to +24 V DC
Reference power: +24 V DC
Power input: ca. 1000 mA
Maximum power input (-20°C): 20 Watt
1.2 System cable SKAxx
Outer diameter: 9.4 mm
Max. bending radius: 150 mm
Material outer sheath: PUR –flame retardant according to
IEC 60322-1-2
Color outer sheath: RAL 9005 matt
Video: 1 x 75 ΩKoax, 19 x 0.127 mm tinned AWG 24,
plated copper braid, shielded
RS 422: 2 x 2 x 0.25 mm2(twisted pair) Cu shielded
double wrapping foil
Supply voltage camera: 2 x 0.75 mm2, polyolefine insulated
Supply voltage heating: 2 x 0.75 mm2, polyolefine insulated
1.3 Mechanical parameters
Housing material: Stainless steel 1.4301 (AISI 304) and
Stainless steel 1.4305 (AISI 303)
Glass material: Borosilicate
Protection level: IP 67 (IEC / EN 60529)
Weight T10-VA:
With K1 flange: ca. 2,000 g
With K2 flange: ca. 2,500 g

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 5 of 20
Dimensions T10-VA [WxHxD]:
K1 flange, without pin and cable gland: 79 x 79 x 128 [mm]
K1 flange, with pin and cable gland: 79 x 96 x 128 [mm]
K2 flange, without pin and cable gland: 79 x 79 x 141 [mm]
K2 flange, with pin and cable gland: 79 x 96 x 141 [mm]
1.4 Temperature range
T10-VA-X-XXX-X-N (without heating): 0° C to +50° C
T10-VA-X-XXX-X-L (with heating): -20° C to +50° C
1.5 Sensor
Sensor: 1/3‘‘ Super HAD CCD II - technology
Effective sensor resolution: PAL: 440,000 pixel (ca. 752 x 582)
NTSC: 380,000 pixel (ca. 768 x 494)
Horizontal resolution: PAL: 530 TV lines
NTSC: 530 TV lines
1.6 Lens
AF-Zoom lens: 10 x optical / 4 x digital
Focal distance (f): 5.1 mm to 51.0 mm
Angle of view: 52° (wide) to 5.4° (tele)
Aperture: F1.8 to F2,1
Minimal illumination: 0.0004 lux (1/4 s, 1/3 s mode & ICR on)
Recommended illumination: 100 to 100.000 lux
Minimal object distance: 150 mm (wide)
800 mm (tele)
1.7 Electronical functions
Electronical shutter function
Serial control via VISCA/RS-422
Composite video (VBS) video output 1 Vpp
Back Light Compensation (BLC)
Auto White Balance (ATW)
Aperture correction (APC)
DSP
SNR: ≥50 dB

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 6 of 20
2 Safety guidelines
Please observe the national and international safety guidelines.
Attention!
External sources of heat and/or cold have to be considered during in-
stallation. The allowed temperature ranges for storage, transportation,
and operational conditions have to be observed!
3 Illustration of the model key
The following model options are currently available for the RoughCam ®niteZoom:
Product name
Model option
Type
housing
option(1)
Meter
SKA02(3)
Cable
termin.(4)
Housing
heating(5)
RoughCam niteZoom
T10-
VA-
005-
K-
N
T10-
VA-
005-
K-
L
T10-
VA-
005-
P-
N
T10-
VA-
005-
P-
L
T10-
VA-
005-
K-
N
T10-
VA-
005-
K-
L
T10-
VA-
005-
P-
N
T10-
VA-
005-
P-
L
(1) VA = Execution in stainless steel
(2) Length of the connection line in meter
(5 meter is the standard length)
(3) K = Terminal block connection (standard)
All signaling lines are spliced to single strands and furnished with wire-end ferrules to allow
connecting the camera to a terminal block
P = Plug- termination
Approximately 30 cm of the system cable’s outer stealth is stripped.
The power supply strands (RD, BK) are furnished with wire-end ferrules.
The AWG24 cable is furnished with a BNC connector
(4) N = Normal Temperature (0° C –50° C)
L = Low Temperature (-20° C –50° C)

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 7 of 20
4 Commissioning
Attention!
Please observe the national regulations regarding security, installa-
tion, and accident prevention!
4.1 Step 1: Installation
Install the RoughCam®niteZoom at the desired location.
Warning!
When the iris is open, the camera must not be directed toward the sun
as this can cause damages to the sensor.
4.2 Step 2: Electrical connection
Attention!
The electrical connection of the equipment must be executed by quali-
fied personnel only!
Attention!
It is mandatory that the housing of the RoughCam®Series has to be
grounded via a PE-connection!
Attention!
Please observe the national regulations regarding security, installa-
tion, and accident prevention!
The RoughCam®niteZoom is delivered with an electrical connection cable type SKAxx
(System Kabel Analog). The maximum cable length is 200 m and can be determined in-
dividually to reflect the particular customer specifications.
The RoughCam®niteZoom is manufactured with a pigtail reflecting the desired cable
length. Depending on the model option, the ending of the camera’s cable connection is
either stripped and furnished with wire-end ferrules or furnished with a BNC connector.

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 8 of 20
4.2.1 Potential equalization
Figure 4.1 Potential equalization T10-VA…
Depending on the housing execution, the equipment’s potential equalization is to be car-
ried out at the place indicated in above figure. The profile of the potential equalization has
to reflect the national grounding instructions (min. 4 mm2).
Connection table:
Potential
Color (IEC 60757)
Profile
Comments
PA
GN/YE
4 mm2 (fix)
4.2.2 Termination of the connection cable (pigtail)
Corresponding to the selected model key, the RoughCam®niteZoom can be delivered
with the following cable termination options:
Figure 4.2 RoughCam niteZoom –T10-VA-B-XXX-K-N

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 9 of 20
Figure 4.3 RoughCam niteZoom –T10-VA-B-XXX-K-L
Figure 4.4 RoughCam niteZoom –T10-VA-B-XXX-P-N
Figure 4.5 RoughCam niteZoom –T10-VA-B-XXX-P-L

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 10 of 20
4.2.3 Power supply & protection
4.2.4 Power supply & protection of the camera’s power circuit
The power supply is to be carried out via the red (RD) as well as black (BK) strand.
Connection table:
Potential
Color (IEC 60757)
Potential level
Profile
Comments
L+
RD
+12 V DC…+30 V DC
0.75 mm2
L-
BK
0 V DC
0.75 mm2
The camera’s maximum power consumption is 6.5 Watt.
The dimensioning of the equipment or the supply protection depends on:
- The selected power supply
- The cable length
- The national regulations
The following safety recommendations may serve as a basis:
Supplied power
Length system cable
Recommended protection
Comments
12 VDC
< 200 m
mT500 mA
24 VDC
< 200 m
mT200 mA
The release current of the protection has to be less than the maximum short-circuit cur-
rent of the power supply (switch-mode power supply)!
4.2.4.1 Power supply & protection of the heating’s power circuit (optional)
The power supply is to be carried out via the grey (GY) as well as the white (WH) strand.
Connection table:
Potential
Color (IEC 60757)
Potential level
Profile
Comments
V+
GY
+12 VDC…+24 VDC
0.75 mm2
V-
WH
0 VDC
0.75 mm2
The heating’s maximum power consumption is 20.0 Watt.

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 11 of 20
The dimensioning of the equipment or the supply protection depends on:
- The selected power supply
- The cable length
- The national regulations
The following safety recommendations may serve as a basis:
Supplied power
Length system cable
Recommended protection
Comments
24 VDC
< 200 m
mT650 mA
The release current of the protection has to be less than the maximum short-circuit cur-
rent of the power supply (switch-mode power supply)!
4.2.5 Video picture connection (CVBS)
Depending on the model key, the video signal of the RoughCam®niteZoom is either pro-
vided with wire-end (K option) or with a BNC connector (P option). The CVBS signal is
only to be connected with the monitor, the video matrix, or the video server.
Connection table (-VA-XXX-K-L)
Potential
Color (IEC 60757)
Potential level
Profile
Comments
CVBS+
WH/ BU
1.0 Vp-p (sync negative)
0.5 mm2
CVBS _GND
BU
0 V
2.7 mm2
Connection table (-VA-XXX-P-L)
Potential
Color (IEC 60757)
Potential level
Profile
Comments
CVBS +
Center (Pin)
1.0 Vp-p (sync negative)
AWG24
CVBS _GND
Shield (bayonet cap)
0 V
4.2.6 Control interface (RS-422)
Potential
(Connection at the control board,
video server, converter etc.)
Potential
(RoughCam nite-
Zoom)
Color
(IEC 60757)
Profile
Comments
TxA
RxA
BN
0.25 mm2
TxB
RxB
YE
0.25 mm2
RxA
TxA
GN
0.25 mm2
RxB
TxB
OG
0.25 mm2

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 12 of 20
4.2.7 Tests prior to switching on voltage
Attention!
Prior to commissioning, all tests as indicated by the national regula-
tions have to be executed. In addition, it is mandatory that the proper
functioning of the operating device in accordance with this user man-
ual and all other applicable regulation has been executed.
Attention!
Incorrect installation and operation of the camera may lead to a loss of
warranty!
4.3 Step 3: Adjusting the picture
Adjustment and optimization of the camera picture such as angle of view, zoom, focus,
back light compensation, or IR cut filter are exclusively carried out electronically via the
camera’s control interface. Mechanical settings at the camera’s block module (Sony
FCB-EX20DP) are neither necessary nor allowed!
For example, control functions can either be operated manually by the means of a Con-
trol Board which has a serial interface (RS-422) and which supports the VISCA protocol
(EVI-D70/D70P) or interactively via the web interface of a video server (figure 4.8) or the
FCB Control Panel (figure 4.7). The transmission rate of the sending and the receiving
end has to be synchronous (figure 4.6).
Figure 4.6 Setting the Baud-transmission rate

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 13 of 20
Figure 4.7 FCB Control Panel of the RoughCam niteZoom
Figure 4.8 Control and visualization via a video server

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 14 of 20
Technical data Sony FCB-EX20DP:
Figure 4.9 RoughCam®niteZoom –lens and sensor board
Lens type
Motorzoom
Lens
10x optical zoom f=5.1 mm (wide) to 51 mm (tele) (F1.8 to F2.1)
Digital zoom
12x (120x with optical zoom)
Sensor
1/3“-Super-HAD-CCD II
Focal distance
5.1 mm –51.0 mm
Horizontally angle of view
52.0° (wide) –5.4° (tele)
Effective pixel count
440,000
Shutter time
1/1 to 1/10000 s (22 steps)
Shutter time
16 steps
Minimal illumination
0.25 lux (F1.8, ICR off, 150 s)
Recommended illumination
100 … 100000 lux
Synchronisation system
Internal/ external (V-Lock)
MOD (Min. Object Distance)
0.01 m (wide end) to 0.8 m (tele end), 0.15 m (standard)
Information!
If not determined differently, the default setting of the RoughCam®ni-
teZoom is wide angle. This means that after the camera has been dis-
connected from the power supply and has been rebooted, it is set to
wide angle mode and standard focus (auto functions are disabled).
In case that the RoughCam niteZoom is supposed to resume certain
settings after the reboot, it is possible to configure „PRESETS“ via the
FCB Control Panel, the video server or the VISCA Control Board.

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 15 of 20
4.3.1 Work preparation
Attention!
Please carry out any preoperational work carefully and in accordance
with the applicable regulations.
4.3.2 Opening the housing
Opening the housing is only necessary for maintenance or repair work. If it is opened,
please make sure not to damage any sealings and tighten the screws correctly as other-
wise the IP protection level IP67 might be voided.

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 16 of 20
5 Maintenance / Servicing
The national regulations concerning the maintenance and servicing of electrical devices
are to be observed.
The required maintenance intervals are specific to the individual devices. The operating
company has to determine these intervals depending on the application parameters. Dur-
ing maintenance, focus has to be put on checking parts concerning the ignition protection
category such as the integrity of the housing, the sealings and the cable glands. If
maintenance measures are necessary they have to be initiated and/or executed.
6 Disposal / Recycling
When disposing of the device, nationally applicable regulations must be observed.
This Document is subject to alterations and additions.

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 17 of 20
7 Drawings
Figure 7.1 T10-VA-K1
Figure 7.2 T10-VA-K2

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 18 of 20
8 Notes

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 19 of 20

Doc.-ID: 180816-PT10BA-HH-RoughCam niteZoom_en_rev.00.docx, page 20 of 20
Schillerstrasse 17, 35102 Lohra-Altenvers
www.samcon.eu, inf[email protected]
fon: [phone], fax: - 31