Samsung AQB09JJWC User manual

ENGLISH
Split-type Air Conditioner
(Cooling and Heating)
ESPAÑOL
FRANÇAIS
ESF DB98-25865A(2)
USER’S MANUAL
AQB09JJWC
AQB12JJWC
AQB18J6WC
AQB24J2WC
Indoor Unit
UQB09JJWC
UQB12JJWC
UQB18J6WC
UQB24J2WC
Outdoor Unit
AQB09JJWC IB_E_DB98-25865 2006.4.14 3:34 PM Page 27

E-2
Safety Precautions
You should take the following safety precautions when using your air conditioner.
◆Do not repair the air conditioner at your discretion.
It is recommended to contact a service center directly.
◆Never spill any kind of liquid on the air conditioner.
If this happens, unplug or turn off the air conditioner and contact an
authorized service center.
◆Do not insert anything between the airflow blades to prevent damage of
the inner fan and consequent injury. Keep children away from the air
conditioner.
◆Do not place any obstacles in front of the air conditioner.
◆Do not spray any kind of liquid into the indoor unit. If this happens,
turn off the breaker and contact a service center.
◆Make sure that the air conditioner is well ventilated at all times:
Do not place a cloth or other materials over it.
◆Remove the batteries if you don’t use the remote control for a long
time. (If applicable)
◆Use the remote control within 23ft(7m) from the indoor unit. (If applicable)
WARNING
DURING OPERATION
◆Never store or load the air conditioner upside down or sideways to
prevent the damage of the compressor.
◆Young children or infirm persons should be always supervised when
they use the air conditioner.
◆Max current is measured according to IEC standard for safety.
◆Current is measured according to ISO standard for energy efficiency.
OTHERS
◆Before throwing out the air conditioner, remove the batteries from the
remote control.
◆When you dispose of the air conditioner, consult your dealer. If pipes
are removed incorrectly, refrigerant may blow out and cause air
pollution. When it contacts with your skin, it can cause skin injury.
◆The package of the air conditioner should be recycled or disposed
properly for environmental reasons.
D ISPOSING OF THE UNIT
• If you don’t follow the safety precautions, you may get the risk of an electric
shock, injury or death.
•The manufacturer or qualified service personnel must install this air conditioner.
• Unplug the electric power before repairing, installing or cleaning.
Register your product at www.samsung.com/global/register
Samsung Electronics Co., Ltd. All Rights Reserved.
AQB09JJWC IB_E_DB98-25865 2006.4.14 3:34 PM Page 2

E-3
ENGLISH
Contents
◆ P REPARATION
■ Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
■ Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
■ Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . . . 6
■ Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . 7
■ Getting Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
◆ O PERATION
■ Selecting the Auto Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
■ Selecting the Cool Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
■ Selecting the Heat Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
■ Selecting the Dry Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
■ Selecting the Fan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
■ Selecting the Tur o Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
■ Selecting the Energy Saving Function . . . . . . . . . . . . . . . . . . . . . 15
■ Adjusting the Airflow Direction Vertically . . . . . . . . . . . . . . . . . . . . 16
■ Adjusting the Airflow Direction Horizontally . . . . . . . . . . . . . . . . . . 17
■ Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
■ Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
■ Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
■ Setting the 1 Hour Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
◆ R ECOMMENDATIONS FOR USE
■ Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
■ Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . 23
■ Operating Your Air Conditioner Without the Remote Control . . . . . 23
■ Trou leshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
■ Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
■ Cleaning Deodorizing and Bio Filter (Option) . . . . . . . . . . . . . . . . 25
◆ T ECHNICAL SPECIFICATIONS
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 3

Name of Each Part
E-4
The design and shape can e changed according to the model.
Indoor Unit
On/Off utton
Air Inlet
Temperature sensor
Air flow lades
(outlet)
Tur o indicator (RED)
Operation indicator (GREEN)
Timer indicator (GREEN)
Air filter
(under the grille)
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 4

E-5
ENGLISH
Air Inlet(Rear)
Air Outlet
Connection Valve
Outdoor Unit
Air Inlet(Rear)
Air Outlet
Connection Valve
Air Inlet(Rear)
Air Outlet
Connection Valve
Outdoor Unit
Outdoor Unit
UQB09JJWC
UQB18J6WC
UQB24J2WC
UQB12JJWC
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 5

Remote Control Buttons and Display
Operation modes indicator
( AUTO, COOL, DRY,
FAN, HEAT)
Transmission indicator
Energy Saving utton
Sleep utton
Mode selection utton
(AUTO, COOL, DRY, FAN, HEAT)
On Timer utton
Off Timer utton
Temperature and Timer setting
Tur o utton
1 Hour Timer utton
1 Hour Timer indicator
Battery life indicator
Battery check utton
Timer Set/Cancel utton
Fan speed indicator
Airflow direction
On Timer indicator
Off Timer indicator
Tur o function indicator
Sleep mode indicator
Energy saving indicator
Power(On/Off) utton
Temperature adjustment utton
Fan speed utton
Airflow control utton
E-6
◆Each mode indicator shows the current setting and the attery life.
◆You can check the attery life y pressing the utton.
◆
The num er of the attery life indicator means the remaining attery life.
Replace the atteries when only one attery life indicator remains.
NN
NNoo oott ttee ee
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 6

E-7
ENGLISH
Inserting the Remote Control Batteries
Remove the attery cover in the rear of the remote control y pushing
it with your thum .
Insert two atteries, respecting the polarities as indicated y
the + and - sym ols.
1
2
Close the cover y sliding it ack in its place.
3
◆Use two AAA, LR03 1.5V atteries.
◆Do not use old atteries or different kinds of atteries together.
◆Batteries may e completely discharged after 12 months,
even if they have not actually een used.
You must insert or replace the remote control batteries when:
◆You purchase the air conditioner
◆The remote control does not work correctly
NN
NNoo oott ttee ee
E-7
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 7

Getting Start
The User’s Manual provides you valuable information about your air conditioner.
Please read this manual carefully before using the air conditioner.
It will help you take full advantage of the unit's features.
You have already seen the basic description of the unit on pages from 4 to 6.
Starting up with the next page, you will find a series of step-by-step procedures
for each function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS PUSH HOLD DOWN
E-8
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 8

Selecting the Auto Mode
ENGLISH
You can select the Auto mode if you want to cool or heat your room
automatically. You can adjust the temperature and the fan speed in
this mode.
1
Press the utton on the remote control until is displayed.
Result:◆The indoor unit eeps each time you press the utton.
◆The air conditioner runs in the Auto mode.
◆The Auto mode cools or heats the room depending on
the set temperature.
◆The air conditioner changes the Cool or Heat mode automatically
depending on the current temperature during operation.
2
You can change modes at any time.
If necessary, press the utton.
Result:◆ The operation indicator on the indoor unit lights up.
◆
The air conditioner starts up in the mode you selected last.
◆The indoor unit eeps.
NN
NNoo oott ttee ee
Press the utton to adjust the temperature until the required
temperature is displayed.
You can set the temperature etween 61°F(16°C) and 86°F(30°C).
Result: Each time you press the utton:
- The temperature is adjusted y 1°F
- The indoor unit eeps
3
E-9
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 9

Selecting the Cool Mode
You can select the Cool mode if you want to cool your room.
You can adjust the temperature and the fan speed when cooling.
E-10
1If necessary, press the utton.
Result: ◆The operation indicator on the indoor unit lights up.
◆The air conditioner starts up in the mode you selected last.
◆The indoor unit eeps.
To control the airflow direction, refer to pages 16 and 17.
5
Press the utton on the remote control until is displayed.
Result: ◆ The indoor unit eeps each time you press the utton.
◆ The air conditioner runs in the Cool mode.
2
You can change modes at any time.
NN
NNoo oott ttee ee
Press the utton to adjust the temperature until the required
temperature is displayed.
You can set the temperature etween 61°F(16°C) and 86°F(30°C).
Result:◆ Each time you press the utton:
- The temperature is adjusted y 1°F
- The indoor unit eeps
◆If the room temperature is higher than the selected
temperature, the air conditioner starts cooling.
◆If the room temperature reaches the set temperature, the air
conditioner stops cooling, ut the fan operates consistently.
3
Press the utton to select the fan speed until the required setting
is displayed.
Automatic (rotated : )
Low
Medium
High
Maximum
Result: Each time you press the utton, the indoor unit
eeps.
4
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 10

ENGLISH
Selecting the Heat Mode
You can select the Heat mode if you want to heat your room.
You can adjust the temperature and the fan speed when heating.
E-11
To control the airflow direction, refer to pages 16 and 17.
5
Press the utton to adjust the temperature until the required
temperature is displayed.
You can set the temperature etween 61°F(16°C) and 86°F(30°C).
Result:◆Each time you press the utton:
- The temperature is adjusted y 1°F
- The indoor unit eeps
◆If the room temperature reaches 9°F higher than the set
temperature, the air conditioner stops heating, ut the fan
operates consistently.
◆If the room temperature reaches 5°F lower than the set
temperature, the air conditioner starts heating again.
3
Press the utton on the remote control until is displayed.
Result:◆ The indoor unit eeps each time you press the utton.
◆ The air conditioner runs in the Heat mode.
2
You can change modes at any time.
NN
NNoo oott ttee ee
1If necessary, press the utton.
Result:◆
The operation indicator on the indoor unit lights up.
◆The air conditioner starts up in the mode you selected last.
◆The indoor unit eeps.
Press the utton to select the fan speed until the required setting
is displayed.
Automatic (rotated : )
Low
Medium
High
Maximum
Result:◆
Each time you press the utton, the indoor unit eeps.
◆For the first 3~5 minutes, the fan may not operate to
prevent the cool air from running out of the indoor unit.
It helps to warm the air in your room sufficiently.
4
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 11

Selecting the Dry Mode
E-12
To control the airflow direction, refer to pages 16 and 17.
4
1If necessary, press the utton.
Result:◆The operation indicator on the indoor unit lights up.
◆The air conditioner starts up in the mode you selected last.
◆The indoor unit eeps.
Press the utton to adjust the temperature until the required
temperature is displayed.
You can set the temperature etween 61°F(16°C) and 86°F(30°C).
Result:◆Each time you press the utton:
- The temperature is adjusted y 1°F
- The indoor unit eeps
◆The air conditioner starts dehumidifying and the fan
speed is adjusted automatically.
3
You can select the Dry mode if you want to dehumidify your room.
You can adjust the temperature in this mode.
Press the utton on the remote control until is displayed.
Result:◆
The indoor unit eeps each time you press the utton.
◆ The air conditioner runs in the Dry mode.
2
You can change modes at any time.
NN
NNoo oott ttee ee
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 12

E-13
ENGLISH
Selecting the Fan Mode
You can select the Fan mode if you want to ventilate your room.
It helps to refresh the air in your room. You can adjust the fan speed
in this mode.
1If necessary, press the utton.
Result:◆The operation indicator on the indoor unit lights up.
◆The air conditioner starts up in the mode you selected last.
◆The indoor unit eeps.
Press the utton to select the fan speed until the required setting
is displayed.
Low
Medium
High
Result: Each time you press the utton, the indoor unit eeps.
3
To control the airflow direction, refer to pages 16 and 17.
4
You can change modes at any time.
NN
NNoo oott ttee ee
Press the utton on the remote control until is displayed.
Result:◆
The indoor unit eeps each time you press the utton.
◆ The air conditioner runs in the Fan mode.
◆ The temperature is set automatically.
2
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 13

E-14
Selecting the Turbo Function
You can select the Turbo Function if you want to cool or heat your
room in the fastest way. After the 30 - minute operation with the
maximum setting, it returns to the previous setting.
Press the utton.
Result:◆The temperature and fan settings are adjusted automatically.
◆The air conditioner cools or heats the room as quickly as possi le.
◆After 30 minutes, the air conditioner is reset automatically to the
previous setting.
◆You can select the Tur o function in the Auto, Cool and Heat mode.
If you select this function in the Dry or Fan mode, the mode
changes to the Auto mode.
2
Press the utton again to stop the Tur o Function efore the end of the
30-minute period.
Result: The air conditioner is reset automatically to the previous setting.
3
To control the airflow direction, refer to pages 16 and 17.
4
1
If necessary, press the utton.
Result:◆The operation indicator on the indoor unit lights up.
◆The air conditioner starts up in the mode you selected last.
◆The indoor unit eeps.
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 14

ENGLISH
Selecting the Energy Saving Function
E-15
You can select the Energy Saving Function to save energy when
cooling or heating.
To control the airflow direction, refer to pages 16 and 17.
Press the utton to select the fan speed until the required
setting is displayed.
Press the utton.
Result:◆
The indoor unit eeps.
◆ The air conditioner runs in the Energy saving mode.
◆ The outer airflow lade moves up and down.
◆ To stop the Energy saving mode, press the again.
2
Press the utton to adjust the temperature until the required
temperature is displayed.
3
4
5
1If necessary, press the utton.
Result:◆The operation indicator on the indoor unit lights up.
◆The air conditioner starts up in the mode you selected last.
◆The indoor unit eeps.
You can select the Energy saving mode only in the Cool
and Heat mode.
NN
NNoo oott ttee ee
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 15

Adjusting the Airflow Direction Vertically
E-16
Press the utton until the required direction is set.
Result: The outer lade is adjusted vertically.
You can adjust the airflow direction vertically. The outer airflow
blade moves up and down to increase the efficiency of the cooling
or heating operation.
NN
NNoo oott ttee eeIf you turn the air conditioner... Then the lade...
off is closed completely.
on set to the default position.
1
Press the utton to move the lade up and down automatically
during operation.
2
Press the utton again to stop the lade moving up and down.
3
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 16

Adjusting the Airflow Direction Horizontally
E-17
ENGLISH
You can adjust the airflow direction horizontally with your hands.
The inner blades with small fins moves the air to the required
direction.
Adjust the inner lades y moving them to left or right.
1
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 17

Setting the On Timer
If you press the utton, oth the On Timer and the Off Timer
are canceled.
NN
NNoo oott ttee ee
You can set the On Timer to turn on the air conditioner automatically
at the appointed time. You can set the time from 1 hour to 24 hours.
Press the utton until the required time is displayed to set the On Timer.
You can set the time etween 1 hour and 24 hours.
1
Press the utton to complete the setting.
Result: ◆The remaining time is displayed.
◆The timer indicator stops linking.
◆The selected mode and the temperature on the display
disappear after 10 seconds.
◆The air conditioner turns on automatically at the appointed
time and the On Timer setting disappears.
2
Press the utton to cancel the On Timer.
E-18
Press the utton until the desired mode is displayed at the top of the
remote control to select the mode in advance.
Result: The air conditioner operates in the selected mode when it is
turned on.
3
To Cancel the On Timer
If you don’t use the remote control after setting the On Timer,
it turns off automatically after 25 hours.
NN
NNoo oott ttee ee
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:23 PM Page 18

Setting the Off Timer
You can set the Off Timer to turn off the air conditioner automatically
at the appointed time. You can set the time from 1 hour to 24 hours.
Press the utton until the required time is displayed to set the Off Timer.
You can set the time etween 1 hour and 24 hours.
1
You can check or change the mode and/or the temperature y
pressing the utton or the utton after setting the
Off Timer.
NN
NNoo oott ttee ee
Press the utton to complete the setting.
Result: ◆The remaining time is displayed.
◆The timer indicator stops linking.
◆The air conditioner turns off automatically at the appointed
time and the Off Timer setting disappears.
2
If you would like to turn the air conditioner on after 2 hours
and to operate it for 2 hours :
1. Press the utton until ‘2 Hr’ is displayed.
2. Press the utton.
3. Press the utton until ‘4 Hr’ is displayed.
4. Press the utton.
EE
EExx xxaa aamm mmpp ppll llee ee
E-19
ENGLISH
If you press the utton, oth the On Timer and the Off Timer
are canceled.
NN
NNoo oott ttee ee
Press the utton to cancel the Off Timer.
To Cancel the Off Timer
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:24 PM Page 19

Setting the Sleep Timer
You can set the Sleep Timer to turn off the air conditioner automatically
while you are sleeping. The air conditioner stops operating 6 hours after
you set the Sleep Timer.
E-20
Cooling The temperature is increased
y 2°F every hour. After the
increase of 4°F,
the temperature is maintained
for 4 hours.
Heating The temperature is decreased
y 2°F every hour. After the
decrease of 4°F,
the temperature is maintained
for 4 hours.
To Cancel the Sleep Timer
Press the utton to cancel the Sleep Timer.
Result:◆The indoor unit eeps.
◆The indicator is no longer displayed.
◆The air conditioner operates normally.
Press the utton until the indicator appears on the remote control.
Result:◆The indoor unit eeps.
◆The air conditioner will e controlled as indicated in the
illustrations elow.
1
You can set Sleep Timer only in the Cool or Heat mode.
NN
NNoo oott ttee ee
AQB09JJWC IB_E_DB98-25865 2006.3.27 8:24 PM Page 20