Samsung MRK-A10N Guide

Receiver & Display Unit
MRK-A10N, MRK-A10UN
Air Conditioner
user & installation manual
imagine the possibilities
Thank you for purchasing this Samsung product.
EN PT ES DE FR EL IT RU TR ZH AR
DB68-03717A-05
SOL Receiver & Display Unit_IBIM_EN_DB68-03717A-05.indd 7 2016-05-12 오전 11:21:53

EN-2
Safety Precautions
Do not attempt to install or repair this receiver & display
unit by yourself.
This receiver & display unit contains no userserviceable
parts. Always consult authorized service personnel for
repairs.
When moving, consult authorized service personnel for
disconnection and installation of the receiver & display
unit.
Ensure that the wall is strong enough to support the
weight of the receiver & display unit.
In the event of a malfunction (burning smell, etc.),
immediately stop operation, turn off the electrical
breaker, and consult authorized service personnel.
Read carefully this installation manual before installation
and check whether the receiver & display unit is installed
correctly after installation.
Must install the receiver & display unit with the wire kit
which is supplied with the unit.
The receiver & display unit must be installed according
to the national electrical rules by an installation
specialist.
When you want to disuse the receiver & display unit,
consult authorized installation center.
WARNING
 Before using the receiver & display unit, read carefully this instructions.
 After reading the instructions, keep this owner’s instructions and the
installation manual in a handy and safe place. If a user is changed, you must
hand over the manuals.
 Never attempt to install the air conditioning system or to move the receiver &
display unit by yourself.
SOL Receiver & Display Unit_IBIM_EN_DB68-03717A-05.indd 2 2016-05-12 오전 11:21:52

EN-3
ENGLISH
CAUTION Do not use inflammable gases near the receiver &
display unit.
Do not spill water into the wired receiver & display unit.
Do not operate the receiver & display unit with wet
hands.
Do not install the receiver & display unit in a location
where it will come into contact with the combustible
gases, machine oil, sulphide gas, etc.
Do not press buttons with a pointed thing.
Do not pull or bend the receiver & display unit cable
excessively.
Do not use this receiver & display unit for other purpose.
Do not spray an insecticide or other combustible things
on the receiver & display unit.
Do not clean the receiver & display unit with benzene,
solvents or other chemicals.
Do not give a shock to the receiver & display unit or
disassemble it by yourself.
Avoid a location where acid/alkali solution or special
spray is used.
Choose a location that is dry and sunny, but not
exposed to direct sunlight. Available temperature is
between 0°C(32°F) and 39°C(102°F).
Do not give tensile strength to the cable to avoid
disconnection.
If the receiver & display unit is installed in a hospital or
other special places, it should not affect other electronic
devices.
SOL Receiver & Display Unit_IBIM_EN_DB68-03717A-05.indd 3 2016-05-12 오전 11:21:52

EN-4
View of the Receiver & Display Unit
Filter sign indicator
Fan indicator
Timer indicator
Remote control sensor
On/Off Indicator(Blue) &
defrost Indicator for heat
pump model (Red)
SOL Receiver & Display Unit_IBIM_EN_DB68-03717A-05.indd 4 2016-05-12 오전 11:21:52

EN-5
ENGLISH
Receiver & Display Unit Installation
Accessories
Receiver & display
unit (1)
PH, +, 2, M2, L10
tapped screw (4)
TH, +, 1, M4, L20
tapped screw (2)
User & Installation
Manual (1)
Wire kit [Length:
10m (32.80ft)]
1
Remove the receiver & display unit cover by using the
tab on its bottom.
2Open the receiver & display unit.
3
Connect the end of the connector wire to the receiver
& display unit and connect the other end of the wire to
the DISPLAY connector of Indoor PCB as shown in figure.
X Do NOT keep the receiver & display unit cable with a
220V cable because the remote controller cables have
low voltage.
Receiver &
display unit
4
Secure the receiver & display unit on the wall with
two screws.
5Reassemble the receiver & display unit cover.
X The receiver & display unit must be installed by an
installation specialist.
X Before installing the receiver & display unit, ensure that
you have turned off the main power.
X All receiver & display unit cables should be installed
according to the national wiring rules and you must install
it in the wall not to be touched by users.
SOL Receiver & Display Unit_IBIM_EN_DB68-03717A-05.indd 5 2016-05-12 오전 11:21:53

SOL Receiver & Display Unit_IBIM_EN_DB68-03717A-05.indd 6 2016-05-12 오전 11:21:53