Samsung SGH D900i - Ultra Edition 12.9 Cell Phone 60... User manual

GSM TELEPHONE
SGH-D900i
GSM TELEPHONE CONTENTS
1. Safety Precautions
2. Specification
3. Operation Instruction and
Installation
4. Array course control
5. Exploded View/Disassembly
and Assembly Instructions
6. MAIN Electrical Parts List
7. Block Diagrams
8. PCB Diagrams
9. Flow Chart of Troubleshooting
10. Reference data

Samsung Electronics Co.,Ltd.
2007. 05. Rev.1.0
ⓒ
This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.
Country Web Site
North America service.samsungportal.com
Latin America latin.samsungportal.com
CIS cis.samsungportal.com
Europe europe.samsungportal.com
China china.samsungportal.com
Asia asia.samsungportal.com
Mideast & Africa mea.samsungportal.com
GSPN (Global Service Partner Network)

SAMSUNG Proprietary-Contents may change without notice
1. Safety Precautions
1-1
This Document can not be used without Samsung's authorization
1-1. Repair Precaution
●Repair in Shield Box, during detailed tuning.
Take specially care of tuning or test,
because specificity of cellular phone is sensitive for surrounding interference(RF noise).
●Be careful to use a kind of magnetic object or tool,
because performance of parts is damaged by the influence of magnetic force.
●Surely use a standard screwdriver when you disassemble this product,
otherwise screw will be worn away.
●Use a thicken twisted wire when you measure level.
A thicken twisted wire has low resistance, therefore error of measurement is few.
●Repair after separate Test Pack and Set because for short danger (for example an
overcurrent and furious flames of parts etc) when you repair board in condition of
connecting Test Pack and tuning on.
●Take specially care of soldering, because Land of PCB is small and weak in heat.
●Surely tune on/off while using AC power plug, because a repair of battery charger is
dangerous when tuning ON/OFF PBA and Connector after disassembling charger.
●Don't use as you pleases after change other material than replacement registered on SEC System.
Otherwise engineer in charge isn't charged with problem that you don't keep this rules.

SAMSUNG Proprietary-Contents may change without notice
Safety Precautions
1-2
This Document can not be used without Samsung's authorization
1-2. ESD(Electrostatically Sensitive Devices) Precaution
Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD
(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.
You can prevent from ESD damage by static electricity.
●Remove static electricity remained your body before you touch semiconductor or parts with
semiconductor. There are ways that you touch an earthed place or wear static electricity
prevention string on wrist.
●Use earthed soldering steel when you connect or disconnect ESD.
●Use soldering removing tool to break static electricity. , otherwise ESD will be damaged by
static electricity.
●Don't unpack until you set up ESD on product. Because most of ESD are packed by box and
aluminum
plate to have conductive power,they are prevented from static electricity.
●You must maintain electric contact between ESD and place due to be set up until ESD is connected
completely to the proper place or a circuit board.

SAMSUNG Proprietary-Contents may change without notice
2. Specification
This Document can not be used without Samsung's authorization
2-1
2-1. GSM General Specification
GSM900
Phase 1 EGSM 900 Phase 2 DCS1800 Phase 1 PCS1900
Freq. Band[MHz]
Uplink/Downlink 890~915 935~960 880~915 925~960 1710~1785 1805~1880 1850~1910 1930~1990
ARFCN range 1~124 0~124 &
975~1023 512~885 512~810
Tx/Rx spacing 45MHz 45MHz 95MHz 80MHz
Mod. Bit rate
/BitPeriod 270.833kbps 3.692us 270.833kbps 3.692us 270.833kbps 3.692us 270.833kbps 3.692us
Time Slot Period
/FramePeriod 576.9us 4.615ms 576.9us 4.615ms 576.9us 4.615ms 576.9us 4.615ms
Modulation 0.3GMSK 0.3GMSK 0.3GMSK 0.3GMSK
MS Power 33dBm~5dBm 33dBm~5dBm 30dBm~0dBm 30dBm~0dBm
Power Class 5pcl ~ 19pcl 5pcl ~ 19pcl 0pcl ~ 15pcl 0pcl ~ 15pcl
Sensitivity -102dBm -102dBm -100dBm -100dBm
TDMA Mux 8 8 8 8
Cell Radius 35Km 35Km 2Km -

SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Specification
2-2
TX Power
control level PCS1900
030±2dBm
128±3dBm
226±3dBm
324±3dBm
422±3dBm
520±3dBm
618±3dBm
716±3dBm
814±3dBm
912±4dBm
10 10±4 dBm
11 8±4dBm
12 6±4 dBm
13 4±4 dBm
14 2±5 dBm
15 0±5 dBm
TX Power
control level DCS1800
030±2dBm
128±3dBm
226±3dBm
324±3dBm
422±3dBm
520±3dBm
618±3dBm
716±3dBm
814±3dBm
912±4dBm
10 10±4 dBm
11 8±4dBm
12 6±4 dBm
13 4±4 dBm
14 2±5 dBm
15 0±5 dBm
TX Power
control level GSM900
GSM850
533±2dBm
631±3dBm
729±3dBm
827±3dBm
925±3dBm
10 23±3 dBm
11 21±3 dBm
12 19±3 dBm
13 17±3 dBm
14 15±3 dBm
15 13±3 dBm
16 11±5 dBm
17 9±5 dBm
18 7±5 dBm
19 5±5 dBm
2-2. GSM TX power class

SAMSUNG Proprietary-Contents may change without notice
Specification
This Document can not be used without Samsung's authorization
2-3
TX Power
control level GSM900
GSM850
8 27±3 dBm
9 25±3 dBm
10 23±3 dBm
11 21±3 dBm
12 19±3 dBm
13 17±3 dBm
14 15±3 dBm
15 13±3 dBm
16 11±5 dBm
17 9±5 dBm
18 7±5 dBm
19 5±5 dBm
TX Power
control level DCS1800
2 26 -4/+3 dBm
3 24±3 dBm
4 22±3 dBm
5 20±3 dBm
6 18±3 dBm
7 16±3 dBm
8 12±3 dBm
9 10±3 dBm
10 14±3 dBm
11 12±4 dBm
12 10±4 dBm
13 8±4dBm
14 6±4 dBm
15 4±4 dBm
2-3. GSM EDGE TX power class
TX Power
control level PCS1900
226-4/+3dBm
324±3dBm
422±3dBm
520±3dBm
618±3dBm
716±3dBm
812±3dBm
910±3dBm
10 14±3 dBm
11 12±4 dBm
12 10±4 dBm
13 8±4dBm
14 6±4 dBm
15 4±4 dBm

SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Specification
2-4

SAMSUNG Proprietary-Contents may change without notice
3. Operation Instruction and Installation
3-1
This Document can not be used without Samsung's authorization
Main Function
-SlimSlide Design Intenna
-3M AF CMOS Camera
-Bluetooth V.2.0
-Stereo Bluetooth Headset
-Mobile Tracker & SOS Messaging
-Large 2.1" 256K Color TFT Display
-SMS/MMS/E-Mail
-WAP 2.0 / Java MIDP 2.0
-MP3,AAC,MP4,3GPPDecoding
-Video Recording and Messaging
-GSM/GPRS/EDGE Class 10
-Quard Band(GSM850,900/DCS,PCS)
-TV-oput, FM radio
-Speaker Phone
-Voice Clarity

SAMSUNG Proprietary-Contents may change without notice
Operation Instruction and Installation
3-2
This Document can not be used without Samsung's authorization

SAMSUNG Proprietary-Contents may change without notice
4. Array course control
4-1
This Document can not be used without Samsung's authorization
4-1. Software Adjustments
Power Supply Cable
Serial Cable(CSA LL64151-A)
Test Jig (GH80-03306A) Test Cable (GH39-00499A)

SAMSUNG Proprietary-Contents may change without notice
Array course control
4-2
This Document can not be used without Samsung's authorization
4-2. Software Downloading
4-2-1. Pre-requsite for Downloading
• Downloader Program(OneNAND Downloder V1.4 Lite For PNX5230.exe)
• E250 Mobile Phone
• Data Cable
• Binary file, TFS file
4-2-2. S/W Downloader Program
■Load the binary download program by executing the
“OneNAND Downloder V1.4 Lite For PNX5230.exe”
1. Select the connected serial port and the rate of speed
2. Select the check box, the mode you want to download.
- if the binary file wanted, check only 'BIN'
- if the tfs file wanted, check only 'TFS'
- if all the files wanted, check 'BIN+TFS'

SAMSUNG Proprietary-Contents may change without notice
Array course control
4-3
This Document can not be used without Samsung's authorization
3. Select the file(s) what you want to download

SAMSUNG Proprietary-Contents may change without notice
Array course control
4-4
This Document can not be used without Samsung's authorization

SAMSUNG Proprietary-Contents may change without notice
5-2
This Document can not be used without Samsung's authorization
5. Exploded View/Disassembly&Assembly Instructions
5-1. Cellular phone Exploded View
QMW01
QIF01
QFU01
QKP01
QME01
QMI03
QMP01
QAN02
QCK01
QRE01
QCR67
QSC13
QSC14
QRE05
QBA00
QSP02
QCA01
QLC01
QPC01
QFL01
QCR67
QSC05
QSC06
QHI01
QKP02
QVO01
QFR01
QCR67
QSD01
QVK01
QBA01
QCR67
QAN06
QSC21
QSC20

SAMSUNG Proprietary-Contents may change without notice
Exploded View/Disassembly&Assembly Instructions
5-2
This Document can not be used without Samsung's authorization
5-2. Cellular phone Parts list
Design LOC Description SEC CODE
QAN02 INTENNA-SGHD900I GH42-01163A
QAN06 ASSY CASE-INTENNA GH98-02033A
QBA00 ASSY CASE-BATT UPPER GH98-02312C
QBA01 INNER BATTERY PACK-800MAH, BLA GH43-02539A
QCA01 UNIT-CAMERA MODULE GH59-04230A
QCK01 PMO-CAMERA KEY GH72-31741A
QCR67 SCREW-MACHINE 6001-002051
QCR67 SCREW-MACHINE 6001-002083
QCR67 SCREW-MACHINE 6001-002083
QCR67 SCREW-MACHINE 6001-002083
QFL01 ASSY CASE-SLIDE LOWER GH98-01211C
QFR01 ASSY CASE-FRONT GH98-01212C
QFU01 ASSY CASE-SLIDE UPPER GH98-01210C
QHI01 ASSY HINGE-PUSH ROD GH98-03808A
QIF01 PMO-COVER IF GH72-31739C
QKP01 ASSY KEYPAD-(SER/XBA) GH98-01859C
QKP02 ASSY KEYPAD-SUB(EU/XBA) GH98-01215C
QLC01 MEA-LCD MODULE KIT(D900I) GH97-07522A
QME01 UNIT-KEY FPCB GH59-04124A
QMI03 RMO-RUBBER MIC HOLDER GH73-08321A
QMP01 PBA MAIN-SGHD900I GH92-03533A
QMW01 ASSY COVER-MAIN WINDOW GH98-01676A
QPC01 MEA-SLIDER FPCB KIT(D900I) GH97-07523A
QRE01 ASSY CASE-REAR GH98-01239C
QRE05 PMO-REAR DECO GH72-31740C
QSC05 RMO-COVER SLIDE SCREW L GH73-07227C
QSC06 RMO-COVER SLIDE SCREW R GH73-07228C
QSC13 RMO-COVER REAR SCREW GH73-07232C
QSC14 RMO-COVER REAR SCREW R GH73-07743C
QSC20 PMO-FRONT DAMPER L GH72-31668C
QSC21 PMO-FRONT DAMPER R GH72-31670C
QSD01 PMO-COVER SD GH72-31738C
QSP02 UNIT-SPEAKER MODULE GH59-03347A
QVK01 UNIT-VOLUME KEY GH59-03265A
QVO01 PMO-VOLUME KEY GH72-31742A

SAMSUNG Proprietary-Contents may change without notice
Exploded View/Disassembly&Assembly Instructions
5-3
This Document can not be used without Samsung's authorization
Description SEC CODE
CBF INTERFACE-DATA LINK CABLE GH39-00444A
ADAPTOR-SGHE690,BLK,EU,A_TYPE GH44-01361A
MPR-TAPE SIDE KEY GH74-25679A
LABEL(R)-WATER SOAK GH68-09361A
AS-DOME SHEET SVC GH81-05846A
MPR-BOHO VINYL LCD CONN GH74-15350A
MPR-INSU TAPE GH74-16483A
MPR-BOHO VINYL LCD GH74-19127A
MPR-INSU TAPE GH74-25670A
MPR-INSU TAPE GH74-25677A
MPR-SPONGE CAMERA FPCB GH74-25687A
MPR-TAPE SLIDE FPCB GH74-25688A
MPR-TAPE LCD ESD GH74-26151A
MPR-TAPE LCD FPCB ESD GH74-26186A
MPR-SPONGE FRONT GH74-26581A
MPR-VINYL BOHO WINDOW GH74-26582A
MPR-TAPE WINDOW MAIN GH74-25307A
MPR-SPONGE CAMERA KEY GH74-25689A
MPR-SPONGE CAMERA KEY GH74-25689A
MPR-TAPE MASKING J TAG GH74-14051A
S/W CD-SGHD900I PC LINK CD GH46-00406A
MANUAL-SFC GH68-04336A
MANUAL USERS-EU RUSSIAN GH68-14238A
BAG PE 6902-000634
CUSHION-CASE(EU-TA2) GH69-04708A
LABEL(R)-MAIN(SER) GH68-14312B
BOX(P)-UNIT(SER) GH69-05179B
UNIT-20P,EARPHONE,BLK,B-TYPE GH59-04029A
MPR-VINYL BOHO MAIN WINDOW V2 GH74-26156A

SAMSUNG Proprietary-Contents may change without notice
Exploded View/Disassembly&Assembly Instructions
5-4
This Document can not be used without Samsung's authorization
5-3. Disassembly and Assembly Instructions
5-3-1. Disassembly
1. Remove 2 screw caps.
2. Loosen a screw this six point form Rear.
1. Make the space between rear cover and
front cover using assembly stick.
2. And then widen space with hand and
separate 2 parts.
1. Remove 2 keys. (Red)
2. Open 2 covers. (Blue)
3. Open the Key connector. (Violet)
1. Upside down the main PBA with moving
slide. Be careful the hook. (Red)
2. Open the LCD connector. (Blue)
12
34

SAMSUNG Proprietary-Contents may change without notice
Exploded View/Disassembly&Assembly Instructions
5-5
This Document can not be used without Samsung's authorization
1. Open the slide. (Slide up)
2. Remove the 4 screw caps with pinset.
1. Loosen a screw 4 point form Lower.
1. Make the space between slide upper and
slide lower using assembly stick.
2. And then widen space with hand and
separate 2 parts.
1. Remove the insulation tape.
2. And separate LCD connector from sub-PBA.
56
78

SAMSUNG Proprietary-Contents may change without notice
Exploded View/Disassembly&Assembly Instructions
5-6
This Document can not be used without Samsung's authorization
1. Separate Camera connector from sub-PBA
and speaker module and camera from slide
upper.
1. Separate sub-PBA from slide upper.
And then caution the hook.
2. Separate LCD module from slide upper using
4 white points.
910