Samsung QP98R-8K User manual

© Samsung Electronics
Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Trademarks other than Samsung Electronics are
property of their respective owners.
QP82R-8K QP98R-8K
The color and the appearance may differ depending on the product, and the content in the
manual is subject to change without prior notice to improve the performance.
Recommended hours of use per day of this product is under16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
Smart Signage User Manual (By Model)
This manual provides information about your Smart Signage including supported types and product specications per model.

Table of contents
Preparations
Checking the Components 3
Parts 4
Ports 5
One Connect 5
Connecting the product to the One Connect 6
Before Installing the Product (Installation
Guide) 7
Tilting Angle and Rotation 7
Ventilation 7
Installing the Wall Mount 8
Preparing before installing Wall-Mount 8
Installing the Wall Mount 8
Wall Mount Kit Specifications (VESA) 9
Specifications
General 10
Preset Timing Modes 11
Appendix
License 12
2

3
Preparations
Chapter 01
"Contact the vendor where you
purchased the product if any
components are missing.
"The appearance of the components
may differ from the images shown.
"The RS232C adapter can be used to
connect to another monitor using the
D-SUB (9-pin) type RS232C cable.
Checking the Components
Quick Setup Guide
Warranty card
(Not available in some
locations)
Regulatory guide
Batteries (AAA x 2)
(Not available in some
locations)
Remote Control
RS232C adapter Holder-Ring (For Wall
Mount) x 4
Stand / Screw (M4 x L14)
x 4
(Supported models:
QP82R-8K)
Stand / Screw (M4 x L20)
x 4
(Supported models:
QP98R-8K)
One Connect
One Connect Power Cable
One Invisible Connection
(Supported models:
QP82R-8K)
One Invisible Connection
/ Screw (M4 x L12)
(Supported models:
QP98R-8K)
HOLDER-CABLE Bending Cover

4
Parts
Control menu Remote sensor & Control button
Power indicator
Speaker
"The color and shape of parts may differ from what is shown. Specifications are subject to change without notice
to improve quality.
Parts Description
Remote sensor
Press a button on the remote control pointing at the bottom of the product face to
perform the function. The remote control sensor is located on the bottom of the product.
"Using other display devices in the same space as the remote control of this product
can cause the other display devices to be inadvertently controlled.
Control button
•button: Turns the product on.
– Press button: Display the Control menu. / Select or run a focused item on the
menu.
– Press and hold button: The running function is terminated.
•Up/Down/Left/Right Button: Move the menu.
•Left/Right Button: Changes the volume.
Control menu
•Home: Enter MagicInfo or URL Launcher mode.
•Settings: Display the OSD menu.
•Return: Exit the control menu.
•Source: Select the connected input source.
•Power Off: Power off the product.
Use the remote control within 2.5 m to 4 m from the sensor on the product at an angle of 30° from the left and
right.
"Store used batteries out of reach of children and recycle.
"Do not use a new and used battery together. Replace both batteries at the same time.
"Remove batteries when the remote control is not to be used for an extended period of time.

5
Ports
One Connect
"The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Port Description
USB 2.0 ¨
Connect to a USB memory device.
POWER
Connect the power cable.
RS232C IN
Connects to MDC using an RS232C adapter.
DIGITAL AUDIO OUT
(OPTICAL)
Connects to a audio device using the optical(digital) cable.
Port Description
LAN
•Connect to a network using the LAN cable. (10/100 Mbps)
•Connect to MDC using the LAN cable.
HDMI IN
Connects to a source device using a HDMI cable or HDMI-DVI cable.
ONE CONNECT
Use the provided One Invisible Connection to connect the product and
One Connect.

6
Connecting the product to the One Connect
One Connect
Bending Cover
10 cm
(4 inches)
QPR-8K
QPR-8K
x 1
(M4 x L12)
One Connect
One Connect
One Connect
Connect the product and One Connect referring to the image.
1
Following the steps 1-4 in the image, use One Invisible Connection to connect the product
and One Connect.
2
Use the power cable to connect One Connect to a wall outlet as shown in step 5.
•Do not install the One Connect upside-down or standing upright on one of its
sides.
•When connecting the One Invisible Connection, use a Bending Cover to bend
the cable. The Bending Cover prevents the cable of the One Invisible Connection
from being bent at a 90 degree angle. Bending the cable at a 90 degree angle
can damage the cable.
•When connecting the One Invisible Connection, pay attention to the shapes and
sizes of its connectors so that they are connected correctly. Failure to do so may
cause product malfunction.
•When connecting the One Invisible Connection, be careful not to twist the
cable of the One Invisible Connection. Failure to do so may cause performance
degradation of the product or damage to the cable.
•When arranging the remaining cable, refer to the figure for the correct
arrangement.
•Take care not to subject the cable to any of the actions below. The One Invisible
Connection contains a power circuit. You could damage the cable and subject
yourself to an electric shock.
Bending Twisting Pulling Pressing on Electric shock
CLASS 1 LASER PRODUCT (One Invisible Connection)
•Caution - Invisible laser radiation when open. Do not stare into beam.
– Do not bend the One Invisible Connection cable excessively. Do not cut the
cable.
– Do not place heavy objects on the cable.
– Do not disassemble either of the cable connectors.
•Caution - Use of controls, adjustments, or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
QP82R-8K QP98R-8K

7
Before Installing the Product (Installation
Guide)
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
•Ensure that an authorized installation company installs the wall mount.
•Otherwise, it may fall and cause personal injury.
•Make sure to install the specified wall mount.
Tilting Angle and Rotation
"Contact Samsung Customer Service Center for further details.
•The product can be tilted at a maximum angle of 15° from a perpendicular wall surface.
•To use the product in Portrait mode, rotate clockwise until the button is positioned as
shown in the images below.
15°
"Do not use this model installed on a ceiling, floor, or table.
Ventilation
"Contact Samsung Customer Service Center for further details.
"Do not install One Connect in an enclosed room. Ensure safe distance from other heat-
emitting products. Excessive internal temperatures may cause fire or product malfunction.
Installation on a PerpendicularWall
AMinimum 40 mm
BAmbient temperature: Under 35 °C
"When installing the product on a perpendicularwall, allow at least
40 mm of space between the product and wall surface for ventilation
and ensure that the ambient temperature is kept below 35 °C.
A
B
Installation on an Indented Wall
AMinimum 40 mm
BMinimum 70 mm
CMinimum 50 mm
DMinimum 50 mm
EAmbient temperature: Under 35 °C
"When installing the product on an indented
wall, allow at least the space specified above
between the product and wall for ventilation
and ensure that the ambient temperature is
kept below 35 °C.
B
D
C
D
B
C
E
A

8
Installing the Wall Mount Preparing before installing Wall-Mount
To install a wall-mount from another manufacturer, use the Holder-Ring.
Installing the Wall Mount
•The wall mount kit (sold separately) allows you to mount the product on the wall.
•The provided image is only for reference. For detailed information on installing the wall mount, see instructions
provided with the wall mount.
•We recommend you contact a technician for assistance when installing the wall mount bracket.
•Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select
to install the wall mount on your own.

9
Wall Mount Kit Specications (VESA)
"Install yourwall mount on a solid wall perpendicular to the floor. To
install the product on the otherwall area, contact the nearest agency.
If you install the product on a slanted wall, it may fall and result in
severe personal injury.
•Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are
provided.
•Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
•Forwall mounts that do not comply with the VESA standard screw specifications, the length of the screws may
differ depending on the wall mount specifications.
•Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to
personal injury. Samsung is not liable for these kinds of accidents.
•Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is
used or the consumer fails to follow the product installation instructions.
•Do not mount the product at more than a 15 degree tilt.
•Always have at least two people mount the product on a wall. (Four or more people for the 82-inch size and
larger models.)
•Standard dimensions forwall mount kits are shown in the table below.
Model Name VESA screw hole specs (A * B) in
millimeters Screw Depth Standard Screw Quantity
QP82R-8K
600 x 400 19-21 M8 4
QP98R-8K
"Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric
shock.

10
Specications
Model Name QP82R-8K QP98R-8K
Panel
Size
82 CLASS (81.5 inches / 207.1
cm)
98 CLASS (97. 5 inches / 247.7
cm)
Display area
1805.4 mm (H) x 1015.5 mm
(V)
2158.848 mm (H) x 1214.352
mm (V)
Resolution
Optimum
resolution
3840 x 2160 @ 60 Hz
Maximum
resolution
3840 x 2160 @ 60 Hz (HDMI 1, HDMI 2, HDMI 3), 7680 x 4320
@ 60 Hz (HDMI 4)
Power Supply
AC100-240V~ 50/60Hz
* Refer to the label at the back of the product as the
standard voltage can vary in different countries.
* On One Connect models, the label is attached to the
bottom of the One Connect.
Environmental
considerations
Operating
Temperature: 32 °F – 104 °F (0 °C – 40 °C)
* For installing the enclosure, keep the internal temperature
at 40 °C or below.
Humidity: 10% – 80%, non-condensing
Storage
Temperature: -4 °F – 113 °F (-20 °C – 45 °C)
Humidity: 5% – 95%, non-condensing
* Applicable before the product package is unpacked.
"Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-
way data exchange between the monitor and PC system optimizes the monitor settings.
Monitor installation takes place automatically. However, you can customize the installation
settings if desired.
"Due to the nature of the manufacturing of this product, approximately1 pixel per
million (1ppm) may appear brighter or darker on the panel. This does not affect product
performance.
"This product can be set to only one resolution for each screen size to obtain the optimum
picture quality due to the nature of the panel. Using a resolution other than the specified
resolution may degrade the picture quality. To avoid this, it is recommended that you select
the optimum resolution specified foryour product.
"For detailed device specifications, visit the Samsung Electronics website.
(USA only)
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website: www.samsung.com/recycling or call,
1‐800‐SAMSUNG
Chapter 02
General