Samsung SVR-1630 User manual

SVR-1630
User Guide

Caution
This device is registered as an EMC for commercial purposes. Vendors and users should be aware of this
EMC registration. If this device is sold or purchased by mistake, the device will need to be altered for
domestic use.
FCC Compliance Statement
Caution : Any changes or modifications in the construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at their own expense.
Warning
This is a class A product. In a domestic environment this product may cause radio interference, in which
case the user may be required to take suitable correction measures
Warning
1. If the built-in Lithium battery is replaced by another type of battery, there is a risk of explosion.
Therefore it is necessary to replace the battery with the same type of battery or an identical one. In
addition, be sure to dispose of worn-out batteries properly because they may cause environmental
pollution.
2. Do not throw the battery into a fire, or heat , disassemble, cut or discharge it because those treatments
can cause the failure of device.
3. Do not recharge the remote controller’s battery.

Cautions
1. Do not put a large monitor or other heavy objects on the SVR-1630 when using it.
2. The SVR-1630 is designed for indoor use and therefore is not waterproof or dampproof. Therefore
before use it is necessary to fully understand the operating environment requirements detailed in the user
manual, and to use the device within the scope of the terms of service. For cleaning the device, wipe it
gently using a clean and dry cloth.
3. The SVR-1630 can be damaged by electric shock. Be careful to use AC power of 110V ~ 220V.
4. The SVR-1630 can be damaged by physical shock because it contains an HDD. Therefore, do not
throw or drop the device.
5. The SVR-1630 is made of metal. If it is thrown at anybody it may cause harm. Install the device in a
safe place out of the reach of children.
6. If the SVR-1630 does not operate correctly, do not disassemble it without authorization. Contact your
local agency for after sales service. The warranty will become invalid if it is disassembled without
authorization.
7. The SVR-1630 can transfer images in real time via a network and can be used for monitoring,
depending on the installation location. Therefore check the laws in the relevant area carefully, and then
install the device in such a way as not to infringe any of its laws.

SVR-1630 Contents
4
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
Contents
Executive Summary................................................................................................................7
1. Product Introduction........................................................................................................7
2. Product Description ........................................................................................................9
2.1 Front View...............................................................................................................9
2.2 Rear View..............................................................................................................12
2.3 Installation Summary.............................................................................................12
Basic Configuration..............................................................................................................13
3. Monitoring ....................................................................................................................13
3.1 View Basic Screen.................................................................................................13
3.2 View Single Image in Full Screen...........................................................................13
3.3 View Multi-Screens................................................................................................13
3.4 Channel Switching.................................................................................................14
3.5 ViewAutomatic Switching Screen..........................................................................14
3.5.1 Basic System Mode........................................................................................14
3.5.2 User Switching Mode......................................................................................15
3.6 View Event Screen ................................................................................................15
3.7 View Enlarged Screen ...........................................................................................16
3.8 PTZ Control...........................................................................................................16
3.8.1 Pan/Tilt Control...............................................................................................16
3.8.2 Zoom/Focus Control .......................................................................................17
3.8.3 Load Preset....................................................................................................17
3.8.4 Save Preset....................................................................................................17
3.8.5 Clear Preset ...................................................................................................17
3.8.6 Auxiliary On....................................................................................................17
3.8.7 Auxiliary Off....................................................................................................17
3.9 Relay Control.........................................................................................................18
3.10 Screen Lock ..........................................................................................................18
3.11 Search System Log ...............................................................................................19
3.12 Monitor B...............................................................................................................20
3.12.1 Monitoring.......................................................................................................20
3.12.2 Multiple Channels Playback............................................................................20
3.12.3 1 Channel Playback........................................................................................21
4. Playback.......................................................................................................................22

Contents SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
5
4.1 Playback Mode......................................................................................................22
4.1.1 Playback in Single Screen Playback Mode......................................................22
4.1.2 Playback in Split Screen (2x2/3x3/4x4) ...........................................................22
4.1.3 Playback of Images of Channel 5 to 16 in 2x2 Split Screen .............................22
4.1.4 Zoom Screen..................................................................................................22
4.1.5 Other Playback Functions...............................................................................23
4.2 Search Mode.........................................................................................................23
4.3 COPY/BACKUP/DELETE......................................................................................25
4.3.1 Copy Image....................................................................................................25
4.3.2 Backup Data...................................................................................................26
4.3.3 Delete Data ....................................................................................................27
4.3.4 Internal/External CD-RW Backup....................................................................27
5. Menu Configuration ......................................................................................................28
5.1 Quick Setup...........................................................................................................28
5.1.1 Time Setting...................................................................................................28
5.1.2 Recording Setup.............................................................................................31
5.2 Camera Setup.......................................................................................................33
5.3 Schedule Record Setup.........................................................................................35
5.3.1 All Channel Setup...........................................................................................35
5.3.1 Setup by Channel...........................................................................................36
5.4 Event Record Setup...............................................................................................39
5.4.1 Sensor Setup..................................................................................................39
5.4.2 Motion Detection Setup...................................................................................40
5.4.3 Text Setup......................................................................................................41
5.4.4 All Channel Event Recording Setup................................................................43
5.4.5 Setup by Channel...........................................................................................44
5.5 Event Action Setup................................................................................................45
5.5.1 Event Schedule ..............................................................................................45
5.5.2 Event Setup....................................................................................................46
5.6 Monitor Setup........................................................................................................47
5.6.1 MonitorA& Monitor B.....................................................................................47
5.6.2 VGAMonitor...................................................................................................48
5.7 System Setup........................................................................................................49
5.7.1 Audio Setup....................................................................................................49
5.7.2 Time Schedule Setup......................................................................................50
5.7.3 Specific Time Setup........................................................................................51
5.7.4 Security Setup................................................................................................52

SVR-1630 Contents
6
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
5.7.5 Disk Setup......................................................................................................53
5.7.6 Network Setup................................................................................................54
5.7.1 Serial Setup....................................................................................................60
5.7.2 Other Functions..............................................................................................61
5.8 Disk Management..................................................................................................63
5.8.1 Disk Manager .................................................................................................64
Expansion..............................................................................................................................66
6. External Device Connection..........................................................................................66
6.1 Use Text Device.....................................................................................................66
6.1.1 Text Setup......................................................................................................66
6.1.2 RS232 Menu Setup in Serial Setup.................................................................67
6.1.3 Setup in Event Recording...............................................................................68
6.1.4 Setup in Schedule Recording..........................................................................69
6.2 Keyboard...............................................................................................................70
6.2.1 COM1 RS232 Menu Setup in Serial Setup......................................................70
6.2.2 PTZ Menu Setup in Serial Setup.....................................................................70
Appendix...............................................................................................................................71
1. Technical Specification..................................................................................................72
2. Use an IPAddress in a Local Network ..........................................................................75
2.1 Executive Summary...............................................................................................75
2.2 IP Configuration and Network Class.......................................................................75
2.3 Class C Network....................................................................................................76

오류! 스타일이 정의되어 있지 않습니다.SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
7
Executive Summary
1. Product Introduction
The SVR-1630 is a new concept DVR, simultaneously saving 16-Channel analog video, audio, text data
and event data. Moreover, its unique Wavelet algorithm enhances image quality and innovatively reduces
video file size.
The SVR-1630, with its unique Wavelet algorithm, presents much clearer and more accurate images with
a better than 50% efficiency over existing JPEG. Through this innovative reduction of file size, the SVR-
1630 can save images from 16 channels in a 200GB Hard Disk, at 5fps per channel, for 15 days. In
addition the SVR-1630 simultaneously saves and plays images with one channel audio.
The SVR-1630 enables users to save CCTV images immediately after power connection, using the quick
setting menu. The quick setting menu is programmed to optimize image quality and storage performance.
Furthermore, the SVR-1630’s storage capacity is easily expanded to 4TB using 2 IEEE 1394 ports. For
convenient backup, the SVR-1630 adopts FAT32, one of the major Windows formats, and so the backed-
up Hard Disk is immediately available through the user’s PC. The SVR-1630 also enables copying of 60
second’s worth of small images using a USB port.

SVR-1630 오류! 스타일이 정의되어 있지 않습니다.
8
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
Major Features
- 16-Channel Video Input
- 1 Channel Audio support
- Simultaneous recording, playback, backup and network recording and playback (Pentaplex)
- Up to 240 fps recording rate
- Up to 480 fps real time display speed
- Real-time monitoring and recording on the PC Monitor and CCTV Monitor
- Dual CCTV Monitor support (1 Normal, 1 Spot)
- VGA Output (1 Normal)
- Built-in Hardware Quad Splitter for Analog Channels
- Built-in software multiplexer for 16-Channel split monitoring
(1 / 2x2/3x3 /4x4 Screen Mode Support)
- Up to 4TB Storage Capacity (Expansion by external HDD using IEEE 1394)
- A variety of recording and playback conditions
- Unique file system for effective event data management
- Saving of image data with relevant text data such as ATM/POS
- 16 Sensor Inputs and 4 Event Outputs
- MD Search (Detailed setting of 64 MD zones)
- Backup using IEEE 1394 (FiWi)
- PTZ control using RS232 and RS485/RS422
- User-friendly 32bit True Color Graphic OSD menu
- Dynamic IP (DHCP, Dynamic IP)
- Unique Wavelet compression algorithm: 1-5KB
- Imbedded Linux OS for safety and efficiency
- Easy interface using Jog/Shuttle
- Remote controller
- Registration of up to 32 DVRs in the SVR Manager (PC user interface)
(Managing a total of 512 Channels (32 DVRs x 16 Channels) as one program)

오류! 스타일이 정의되어 있지 않습니다.SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
9
2. Product Description
2.1 Front View
(1) Status LED
HDD : flashes when the HDD is active
RX/TX : flashes during monitoring on a network
REC : flashes during image saving
(2) Remote Controller Receiver
(3) IEEE 1394 and USB Interface
IEEE1394 and USB Port, one each
(4) Function Buttons (5) Channel Buttons
(3) IEEE 1394 &
USBInterface
(6) Play
(1) Status LED
(2) Remote Controlle
r
Receiver
(6) Jog/Shuttle

SVR-1630 오류! 스타일이 정의되어 있지 않습니다.
10
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
(4) Function Buttons
ESC : goes to the higher menu in the setting or locks the screen
MENU(▲) : sets menu
COPY : copies, backs up or deletes images saved in the 1 Screen Mode
AUTO(◀) : switches and views all images from all cameras connected
Press this button for over 1 sec to activate the User Sequnce Mode
ENTER
HELP : selects when setting
Displays image data in the Monitoring/Playback Mode
A/B(▶) : selects the monitor (A or B) to control
AR RST : turns the Relay on or off in the Monitoring Mode.
Returns to the original status in case of event pop-up.
RELAY(▼) : manually controls the Relay Output
ZOOM : Enlarges images in the 1 Screen Mode
(5) Channel Buttons
Selects the video channels for monitoring and playback.
Each channel button has an LED at the top and the LEDs indicate status by their color
(6) Play Button
ENTER
PTZ : opens the PTZ control menu or setting menu
SEARCH
PRESET : searches the images/events saved in the 1 Screen Playback Mode
searches the logs saved in the Monitoring Mode
Switches to Preset Load in the PTZ Mode
MULTI
ESC : changes the Split Screen Mode
: goes to the previous step in the menu
REC : converts the current recording status
Keeps the ON status during REC waiting status.
SLOW : plays slower than normal speed
PLAY
PAUSE : starts and pauses playback (still image is displayed)
STOP : stops the Playback Mode
FAST : plays faster than normal speed
DIR : changes the playback direction
Jog Dial : changes the playback direction
Shuttle : adjusts the playback speed

오류! 스타일이 정의되어 있지 않습니다.SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
11
(7) Jog Shuttle
(8) Power Switch
Power On/Off switch. On OFF, the power off procedure varies depending on the system setting. See the
section “4.5 Supplying Power and Running” in “Install Manual” for more details.

SVR-1630 오류! 스타일이 정의되어 있지 않습니다.
12
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
2.2 Rear View
(1) Audio In/Out
One andio input and one audio output terminal
(2) Ethernet
(3) Power Connection
(4) Video Input and Loopback
16 Video Input Terminals and Loopback Terminals
(5) Video Output
4 Video Output Terminals (2 Normal CVBS, 1 Normal Y/C, 1 Spot)
(6) Serial and DIO Port
Sensor In : Block of 16 Sensor Input Terminals
Relay Out : Block of 4 Relay Output Terminals
COM1 : RS232 9Pin D-Sub Connectors
COM2 : RS422/485 Terminal Block
COM3/COM4 : RS232 & RS422/485, RJ45 Connectors
IEE1394 : IEEE 1394 Connector
(7) VGA Port
1 VGA Video Output Terminal
2.3 Installation Summary
- Camera Connection
- Monitor Connection
- Ethernet Connection (for remote access to the DVR or for registering IP cameras)
- Audio Connnection
- Power Connection and Start-up
(2) Power Connection
(1) Audio In/Out
(4) Video Input & Loopback
(7) VGA Port
(6) Serial & DIO Port
(5) Video Output
(2) Ethernet

오류! 스타일이 정의되어 있지 않습니다.SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
13
Basic Configuration
3. Monitoring
When the SVR-1630 is on, images from all channels are displayed in Monitor Mode. (When 8
Channels are connected, the images are displayed on the 3x3 split screen). This section is for using
all the SVR-1630 monitoring modes.
<Cautions>
The SVR-1630 supports dual monitors (A and B). Monitor A (Normal) supports all the functions
described below and Monitor B (Spot) doesn’t support split screen, or Menu and Zoom functions. When
Monitor A is in Playback Mode, Monitor B doesn’t work in Playback Mode.
Therefore the functions described below are based on Monitor A.
In addition, Monitor A should be activated for functional controls.
3.1 View Basic Screen
- When the power is switched on, the SVR-1630 starts automatically.
- The LED goes on and booting is started.
- After the completion of booting, the screen is
displayed in split display mode, depending on
the number of channels connected (the figure
to the right is an example of 4 Channel
display)
※If a User Password is set, the Password
Input window is shown.
3.2 View Single Image in Full Screen
- Enter the channel number to view.
- Press the [MULTI] button, and the split
screen is displayed again.
3.3 View Multi-Screens
- Press the [MULTI] button to simultaneously
view multiple channels.
- Each time the [MULTI] button is pressed, the
screen is switched to 2x2, 3x3 and 4x4 Split
Screen Mode in sequence

SVR-1630 오류! 스타일이 정의되어 있지 않습니다.
14
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
3.4 Channel Switching
Rotate the Shuttle Ring in Single Screen or Multi Screen Mode, and the screen shows the next channel’s
image.
3.5 View Automatic Switching Screen
The Automatic Switching Mode consists of a Basic System Mode and a User Switching Mode defined by
the user. Press the [AUTO] button for over one second, and the User Switching Mode is activated.
3.5.1 Basic System Mode
-Automatically switches all channels using the [AUTO] button.
- Press the [MENU] button to set the switching interval (default value is 5 Sec.)
- Go to “Monitor” in the OSD menu.
- Go to “Monitor A”, the sub-menu of “Monitor”, and press [ENTER].
- Set the desired value between 1 to 60 seconds by selecting “Seq. Switching (sec)”. When it is set to OFF,
the Automatic Switching Mode doesn’t work.
- Press the [AUTO] button in any of the Split Modes except the 4x4 Split Screen, and the Automatic
Switching Mode is activated.
- To end the Automatic Switching Mode, press the [AUTO] button again.
<Caution>
Basic System Mode is available when the number of cameras connected is higher than the number of
current split screens. That is, when more than 2 cameras are connected in Single Screen Mode and more
than 5 cameras in 2x2 Split Mode. Automatic Switching doesn’t work in 4x4 Split Mode.

오류! 스타일이 정의되어 있지 않습니다.SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
15
3.5.2 User Switching Mode
- Press the [AUTO] button for over 1 second.
- For User Switching Mode, set the User Sequence Configuration item in the OSD Menu “Monitor A”.
<Cautions>
1. The User Switching Mode can define up to 16 Channels.
2. The figure above defines 6 sequences in order: 2x2 Split Screen (1,2,3,4) ÆFull Screen (1) Æ2x2
Split Screen (5,6,7,8) ÆFull Screen (5) ÆFull Screen (8) Æ3x3 Split Screen
(9,10,11,12,13,14,15,16).
3.6 View Event Screen
- When an event occurs, it is possible to set the relevant screen to be displayed automatically.
- For the relevant Pop-up window cycle, set the time in “Event Pop-Up (sec)” under “Monitor A”.
- When several events occur simultaneously in several channels, split screens corresponding to the
number of the relevant channel are displayed. For example, if events occur in three channels, the
relevant images are automatically displayed on the 2x2 Split Screen. To return to the original screen,
press any button.
<Cautions>
1. When Event Pop-up Hold (sec) is off, the Event Pop-up function doesn’t work.
2. When Event Pop-up Hold (sec) is set to Keep, the original screen is not displayed unless you press
one of the buttons.

SVR-1630 오류! 스타일이 정의되어 있지 않습니다.
16
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
3.7 View Enlarged Screen
- Press the [ZOOM] button in Single Full Screen Mode, and the image is enlarged X 2.
- When the [ZOOM] button is pressed, the position of the enlarged screen is in the center. You can move
the enlarged screen by 10 steps to the right and left and 7 steps upward and downward.
- Use the Jog Dial and Shuttle to move the screen.
- Press the [ZOOM] button again, and the screen is returned to the original size.
3.8 PTZ Control
- Connect the PTZ Controller to the DVR and set the relevant protocol in the “Serial Setup” menu. You
can control the PTZ while watching images in real time.
- Press the Channel Button to control the PTZ, and the Single Screen Mode activates.
- Press the [PTZ] button, and you can control Pan/Tilt. Press the button again, and you can control
Zoom/Focus. Each time you press the [PTZ] button, PAN/TILT and ZOOM/FOCUS are toggled.
- Under the Pan/Tilt or Zoom/Focus control mode, press the [MENU] button, and the PTZ menu (Pan/Tilt,
Zoom/Focus, Load Preset, Save Preset, Clear Preset, Auxiliary On, Auxiliary Off) is displayed.
- Select the desired menu and press the [ENTER] button.
3.8.1 Pan/Tilt Control
This menu is for using the PAN and TILT function in Real-Time Monitoring Mode.
- Select “Pan/Tilt” in the PTZ Menu OSD.
- Control Pan and Tilt using the arrow keys on the front.
Pan : Left and Right Key. Tilt : Up/Down Key

오류! 스타일이 정의되어 있지 않습니다.SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
17
3.8.2 Zoom/Focus Control
This menu is for using the Zoom and Focus function in Real-Time Monitoring Mode.
- Select ‘Zoom/ Focus’ in the PTZ Menu OSD.
- Control Zoom and Focus using the arrow keys on the front.
Zoom : Left and Right Key. Focus : Up/Down Key
3.8.3 Load Preset
This menu is for moving to a preset location in Real-Time Monitoring Mode.
- Select ‘Load Preset’ in Real-Time Monitoring Mode.
- Press the relevant preset number button
3.8.4 Save Preset
This menu is for presetting a new location in Real-Time Monitoring Mode.
- Adjust the camera position using the ‘Pan/Tilt’ and ‘Zoom/Focus’ menus.
- Press the [MENU] button.
- Select ‘Save Preset’ in the PTZ Menu OSD.
- Press the number button to preset.
3.8.5 Clear Preset
This menu is for deleting a saved preset.
- Press the [MENU] button under PTZ control mode.
- Select “Clear Preset” in the PTZ Menu OSD.
- Press the Preset Number to delete (1~16)
3.8.6 Auxiliary On
This menu is for using a PTZ Auxiliary.
- Press the [MENU] button under PTZ control mode.
- Select “Auxiliary On” in the PTZ Menu OSD.
- Press the Auxiliary Number to use (1~16)
3.8.7 Auxiliary Off
This menu is for releasing a PTZ Auxiliary.
- Press the [MENU] button under PTZ control mode.
- Select “Auxiliary Off” in the PTZ Menu OSD.
- Press the Auxiliary Number to release (1~16)

SVR-1630 오류! 스타일이 정의되어 있지 않습니다.
18
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
3.9 Relay Control
- This menu turns the Relay on or off. (The SVR-1630 supports 4 Relay outputs.)
- Press the [RELAY] button.
- The “Relay On” Icon is displayed on the screen.
- Press the relevant Relay number (from 1 to 4), and the Relay Output signal is transmitted.
- Press the [RELAY] button twice to release Relay. The “Relay Off” Icon is then displayed.
- Press the Relay Number to release, and the relevant Relay is off.
3.10 Screen Lock
- This menu is for preventing unauthorized users from controlling the menu when an administrator or
authorized user is not on site.
- This function requires the setting of a “User Password” prior to use.
- Press the [Esc] button, and the “Screen Locked” message is shown at the bottom. Lock Mode is activated.
- In Lock Mode, none of the buttons work. The buttons are reactivated when Lock Mode is released.
- Whenever you press any button in Lock Mode, the “User Password” window is displayed. Enter the
relevant password, and Lock Mode is released.

오류! 스타일이 정의되어 있지 않습니다.SVR-1630
Samsung Techwin CO.,Ltd.
2004.07.2001 (v 1.0)
19
3.11 Search System Log
Press the ‘SEARCH’ key, and the menu for selecting events and system logs appears. Select the System
Log in the menu, and you can search for system logs.
Up to 1,000 logs can be saved. When the number of logs exceeds 1,000, the oldest log is deleted.
The log types are described below.
Power On : The power is connected.
Power Off : The power is disconnected correctly using the switch on the front.
Power Interrupt : The power is disconnected in error.
Config Changed : The configuration is changed by the menu or network manager.
Record Off : Recording is stopped by pressing the REC switch.
Record On : Recording is resumed by press the REC switch.
Time Shift Start : When the time is changed, the time before the change is displayed.
Time Shift Finish : When the time is changed, the time after the change is displayed.

SVR-1630 오류! 스타일이 정의되어 있지 않습니다.
20
2004.07.2001 (v 1.0)
Samsung Techwin CO.,Ltd.
3.12 Monitor B
3.12.1 Monitoring
Monitor A monitors the images from multiple channels and Monitor B monitors the image from one
channel in a large screen. You can monitor in a variety of combinations as explained below.
Monitor A Monitor B Remarks
4x4 Split Screen
Mode
1 Channel Monitoring Separately monitors the most important channel while
monitoring the images of 16 other channels
3x3 Split Sceen
Mode
User Switching Monitors 7 channels in the User Switching Mode while
monitoring 9 channels in the 3x3 Split Screen Mode
2x2 Split Screen
Sequence
1 Channel Monitoring Separately monitors the important channels while
monitoring images by 4-channel in Automatic
Switching Mode
3.12.2 Multiple Channels Playback
Monitor A searches and plays several images in split screen and Monitor B monitors the image from one
channel in a large screen. That is, it is possible to monitor channels during playback.