Samsung Galaxy FE Buds2 User manual

https://tehnoteka.rs
Uputstvo za upotrebu (EN)
SAMSUNG slušalice Galaxy FE Buds2 sive
Tehnoteka je online destinacija za upoređivanje cena i karakteristika bele tehnike,
potrošačke elektronike i IT uređaja kod trgovinskih lanaca i internet prodavnica u Srbiji.
Naša stranica vam omogućava da istražite najnovije informacije, detaljne karakteristike
i konkurentne cene proizvoda.
Posetite nas i uživajte u ekskluzivnom iskustvu pametne kupovine klikom na link:
https://tehnoteka.rs/p/samsung-slusalice-galaxy-fe-buds2-sive-akcija-cena/
1 / 50

www.samsung.com
USER MANUAL
English. 09/2023. Rev.1.0
SM-R400N
2 / 501 / 482 / 50

2
Table of Contents
Getting started
3 About the Galaxy Buds FE
4 Device layout and functions
6 Preparing the earbuds for use
8 Charging the battery
12 Battery indicator lights identification
Using the earbuds
14 Connecting the earbuds to a mobile
device
18 Wearing the earbuds
20 Using the earbud by touch
23 Using the noise controls mode
24 Listening to music
25 Using the equaliser
26 Using call features
27 Bixby
Galaxy Wearable app
29 Introduction
30 Connecting and disconnecting the
earbuds
31 Configuring settings for the Galaxy
Buds FE
Usage notices
37 Precautions for using the device
38 Notes on package contents and
accessories
39 Precautions for using the earbuds
40 Cleaning and managing the Galaxy
Buds FE
41 Restarting the earbuds
42 Coupling the earbuds
Appendix
43 Troubleshooting
47 Removing the battery
3 / 502 / 483 / 50

3
Getting started
About the Galaxy Buds FE
Galaxy Buds FE are wireless earbuds which allow you to listen to music or answer
incoming calls after connecting them to your mobile device even while doing other
activities, such as working out.
Do not wear the earbuds in high-traffic areas, such as roads or crosswalks. Doing so
may result in accidents because of slowed reaction times.
4 / 503 / 484 / 50

Getting started
4
Device layout and functions
Earbud
Touch-sensitive sensor
Speaker
Charging contacts
Microphone
Microphone
Wing tip
Ear tip
Antenna / Touch area
Wing tip
Direction indicator
M/L
Direction indicator
S/M
5 / 504 / 485 / 50

Getting started
5
Charging case
Charging contacts
(right)
Charging contacts
(left)
Earbud battery
indicator light
Charger port
(USB Type-C)
Charging case
battery indicator
light
•
Use the device in a place without magnetic interference for the device to operate
normally.
•
Your device and some accessories (sold separately) contain magnets. Keep
it away from credit cards, implanted medical devices, and other devices that
may be affected by magnets. In the case of medical devices, keep your device
more than 15 cm apart. Stop using your device if you suspect any interference
with your medical device and consult your physician oryour medical device
manufacturer.
•
If you have a medical implant in your heart, do not place your device in a pocket
close to your implanted device, such as your chest or inner jacket pocket.
•
Keep a safe distance between objects that are affected by magnets, and your
device and some accessories (sold separately) that contain magnets. Objects
such as credit cards, passbooks, access cards, boarding passes, or parking passes
may be damaged or disabled by the magnets in the device.
If you use the earbuds when they are broken, there may be a risk of injury. Use
the earbuds only after they have been repaired at a Samsung Service Centre or an
authorised service centre.
6 / 505 / 486 / 50

Getting started
6
•
If foreign materials are placed on the touch-sensitive sensor, they may cause the
sensor to malfunction. Before wearing the earbuds, clean the sensor first.
•
If there is sweat or liquid on the charging contacts, corrosion may occur on
the Galaxy Buds FE. When there is sweat or liquid on the charging contacts or
earbuds, clean them before inserting the earbuds in the charging case.
•
Prevent water from coming into contact with the touch area. The touch feature
may malfunction in humid conditions orwhen exposed to water.
Preparing the earbuds for use
Attaching an ear tip to the earbud
•
Do not put the earbuds in your ears without ear tips. Doing so may hurt your
ears.
•
Do not pull the ear tip excessively when you attach or detach it. The ear tip may
tear.
•
Do not press the ear tip excessively or twist it. The ear tip may be damaged.
1 Select the ear tip that fits your ear.
2 Align the latch at the bottom of the earbud and groove of the ear tip and cover the
latch with the ear tip.
Push the ear tip all the way in so that it does not come out.
3 Follow the same procedure for the opposite earbud.
7 / 506 / 487 / 50

Getting started
7
Attaching a wing tip to the earbud
1 Select the wing tip that fits your ear.
2 Select the wing tip for the left or right ear.
3 Hook the wing tip’s groove to earbud’s fixation hook and cover the earbud with the
wing tip.
•
Do not put the earbuds in your ears without wing tips. Doing so may hurt your
ears.
•
Do not pull the wing tip excessively when you attach or detach it. The wing tip
may tear.
•
Do not put the wing tips on the earbuds in the wrong direction. The earbuds will
not fit in your ears properly.
•
Check the left and right imprinted direction marks on the wing tips and earbuds,
and check if the wing tips are inserted as shown in the image.
8 / 507 / 488 / 50

Getting started
8
M/L
S/M
4 Follow the same procedure for the opposite earbud.
Charging the battery
Fully charge the battery before using the earbuds for the first time or when they have
been unused for extended periods. The earbuds will start to work while charging. When
you charge the battery for the first time or when the battery is completely discharged, it
needs at least 10 minutes to start to work.
The charging case, which has a built-in battery, is charged along with the earbuds that
are in the charging case when connected to the charger.
If you put the earbuds in a completely discharged charging case, they may emit a
sound. Sufficiently charge the charging case before inserting the earbuds.
1 Open the charging case.
9 / 508 / 489 / 50

Getting started
9
2 Check the direction of each earbud and correctly insert them into their corresponding
slots in the charging case.
R
L
3 Close the charging case.
10 / 509 / 4810 / 50

Getting started
10
4 Connect the USB cable to the charger and then plug the USB cable into the charger
port.
5 Plug the charger into an electric socket.
The batteries of the earbuds and the charging case are charged simultaneously.
6 After fully charging, disconnect the charging case from the charger. First disconnect
the USB cable from the charging case and then unplug the charger from the electric
socket.
Checking the battery level
Connect the earbuds to your mobile device, open the Galaxy Wearable app on your
mobile device, and check the battery status of the earbuds and the charging case. Refer
to Connecting the earbuds to a mobile device for more information.
When the remaining battery level is low, a notification will appear on your mobile
device’s notification panel.
Reducing the battery consumption
When you are not using the earbuds, store them in a charging case that has been
charged. If not, the touch-sensitive sensorwill continue to work, and it will affect to the
usage time and battery consumption.
11 / 5010 / 4811 / 50

Getting started
11
Battery charging tips and precautions
Use only Samsung-approved charger and cable specifically designed foryour
Galaxy Buds FE. Incompatible charger and cable can cause serious injuries or
damage to your device.
•
Connecting the charger improperly may cause serious damage to the charging
case. Any damage caused by misuse is not covered by the warranty.
•
Use only USB Type-C cable supplied with the Galaxy Buds FE. The charging case
may be damaged if you use Micro USB cable.
•
If you charge the Galaxy Buds FE while the charger port is wet, the Galaxy Buds
FE may be damaged. Thoroughly dry the charger port before charging the Galaxy
Buds FE.
•
Chargers are sold separately.
•
To save energy, unplug the charger when not in use. The charger does not have a
power switch, so you must unplug the charger from the electric socket when not
in use to avoid wasting power.
•
When using a charger, it is recommended to use an approved charger that
guarantees the charging performance.
•
Keep the charging case closed while you store or charge the earbuds, orwhen
you charge the charging case.
•
If you touch the charging contacts while charging the charging case, it may
affect charging.
•
If there is sweat or liquid on the charging contacts, corrosion may occur on
the Galaxy Buds FE. When there is sweat or liquid on the charging contacts or
earbuds, clean them before inserting the earbuds in the charging case.
•
When you insert your earbuds in the charging case, the charging will start
automatically, and it will stop automatically if earbuds are fully charged.
•
It will likely not have a huge impact on the life of your Galaxy Buds FE even if you
do not remove your earbuds from the charging case after the earbuds are fully
charged.
•
If you will not be using your Galaxy Buds FE for a long time, store them after they
are charged.
•
Do not put the wing tips on the earbuds in the wrong direction. The earbuds will
not be charged if they are not properly inserted into the charging case.
12 / 5011 / 4812 / 50

Getting started
12
•
Using a power source other than the charger, such as a computer, may result in a
slower charging speed because of a lower electric current.
•
While charging, the Galaxy Buds FE and the charger may heat up. This is normal
and should not affect the Galaxy Buds FE lifespan or performance. If the battery
gets hotter than usual, the charger may stop charging.
•
If the Galaxy Buds FE are not charging properly, take the Galaxy Buds FE and the
charger to a Samsung Service Centre or an authorised service centre.
•
Avoid bending the USB cable. Doing so may damage or reduce the lifespan of the
USB cable. Never use a damaged USB cable.
Battery indicator lights identification
The battery indicator lights inform you of your earbuds and the charging case’s charging
status.
The earbud battery indicator light is located inside of the charging case and shows the
charging status of the earbuds. The charging case battery indicator light on the front of
the charging case indicates the charging status of the case itself.
Earbud battery indicator light
Earbud battery
indicator light
Colour Status
Continuously red
•
Charging
Continuously green
•
Fully charged
Flashes red
•
Charging blocked because of abnormal temperatures
13 / 5012 / 4813 / 50

Getting started
13
Charging case battery indicator light
Charging case battery
indicator light
Colour Status
Continuously red
•
Charging
Continuously green
•
Fully charged
Flashes red
•
Charging blocked because of abnormal temperatures
Flashes red (flashes after
closing the charging case)
•
Battery power is low (lower than 10%)
Red (stays on for 5 seconds
after closing the charging
case)
•
Battery power is low (between 10% and 29%)
Yellow (stays on for
5 seconds after closing the
charging case)
•
Battery power is moderate (between 30% and 59%)
Green (stays on for
5 seconds after closing the
charging case)
•
Battery power is high (more than 60%)
If the battery indicator lights do not work as described, disconnect the charger
from the charging case and reconnect it.
14 / 5013 / 4814 / 50

14
Using the earbuds
Connecting the earbuds to a mobile device
Before the connection
•
Charge the charging case sufficiently.
•
The Galaxy Wearable app must be installed on your mobile device. If the app is not
installed on your mobile device, download the app from
Galaxy Store or Play Store .
•
You can download the Galaxy Wearable app only on mobile devices running
Android OS version 8.0 (API 26), or later, and with 1.5 GB of memory or more.
•
You can change the language of the Galaxy Wearable app on your mobile
device. Open
Settings on your mobile device and tap General management
→
Language . English may appear by default if the selected language on
Settings is not supported on the Galaxy Wearable app.
Connecting the earbuds to a Samsung mobile device for the
first time
1 Check the direction of each earbud and correctly insert them into their corresponding
slots in the charging case.
If the earbud battery indicator light does not flash, connect the charging case to the
charger and charge them for more than 10 minutes.
2 Close the charging case.
3 Open the charging case.
The earbuds will enter Bluetooth pairing mode automatically and a pop-up window
will appear on your mobile device.
If the pop-up window does not appear or if you want to connect to a non-Samsung
mobile device that also uses the Android OS, refer to Connecting the earbuds to a
non-Samsung mobile device that also uses the Android OS (or, the connection pop-up
window does not appear).
15 / 5014 / 4815 / 50

Using the earbuds
15
When the charging case battery indicator light flashes in red, take out the earbuds
from the charging case and insert them into the case again.
4 On your mobile device, tap Connect on the pop-up window and follow the on-screen
instructions to complete the connection.
Once the connection has been established, the earbuds will be automatically
connected to your mobile device wheneveryou open the charging case while the
earbuds are inside it.
•
You can download the Galaxy Wearable app only on mobile devices running
Android OS version 8.0 (API 26), or later, and with 1.5 GB of memory or more.
•
Connection methods may vary depending on your mobile device and software
version.
•
The connection pop-up window will appear only on Samsung mobile devices
running Android OS version 9.0 or later that have the SmartThings app installed.
If the pop-up window does not appear, update the SmartThings app to the latest
version.
•
The appearance of the pop-up window may vary depending on your connected
mobile device.
•
If the earbuds do not connect to a mobile device within 3 minutes, Bluetooth
pairing mode will be turned off. Close the charging case again and open it. The
earbuds will enter Bluetooth pairing mode.
•
If you want to connect to another mobile device after a connection has been
established, refer to Connecting with other devices after disconnecting from the
previous mobile device.
16 / 5015 / 4816 / 50

Using the earbuds
16
•
When connecting earbuds with a mobile device that has been signed in to a
Samsung account, the earbuds pairing information will be synced on the other
mobile devices that use the same Samsung account and you do not need to
pair them at the beginning again. To connect the other devices that use the
same Samsung account with the earbuds, on the mobile devices that you want
to connect, open
Settings , tap Connections
→
Bluetooth , and then select the
earbuds synced through the Samsung account.
•
If only a single earbud is connected to your mobile device, you will hear the
sound in mono. It will automatically switch to stereo mode when both earbuds
are connected to your mobile device.
•
If the earbuds do not connect to a mobile device, the connection pop-up window
does not appear, oryour mobile device cannot find the earbuds, store them in
the charging case and touch and hold both earbuds for more than 3 seconds to
enter Bluetooth pairing mode manually. When Bluetooth pairing mode has been
entered, the earbud battery indicator light will flash red and green.
17 / 5016 / 4817 / 50

Using the earbuds
17
Connecting the earbuds to a non-Samsung mobile device
that also uses the Android OS (or, the connection pop-up
window does not appear)
If you connect to a non-Samsung mobile device that also uses the Android OS,
some of the features of the earbuds may not be available and the earbuds may not
work properly.
1 Check the direction of each earbud and correctly insert them into their corresponding
slots in the charging case.
If the earbud battery indicator light does not flash, connect the charging case to the
charger and charge them for more than 10 minutes.
2 Close the charging case.
3 Open the charging case.
The earbuds will enter Bluetooth pairing mode automatically.
4 On your mobile device, turn on the Bluetooth feature to connect the earbuds to
your mobile device, open the
Galaxy Wearable app, and then follow the on-screen
instructions to complete the connection.
Precautions for using Bluetooth
•
To avoid problems when connecting your earbuds to another device, place the
devices close to each other.
•
Ensure that your earbuds and the other Bluetooth device are within the
maximum Bluetooth connection range (10 m). The distance may vary depending
on the environment the devices are used in.
•
Ensure that there are no obstacles between the earbuds and a connected device,
including human bodies, walls, corners, or fences.
•
Do not touch the Bluetooth antenna of a connected device.
•
Bluetooth uses the same frequency as some industrial, scientific, medical, and
low power products and interference may occurwhen making connections near
these types of products.
•
Some devices, especially those that are not tested or approved by the Bluetooth
SIG, may be incompatible with the earbuds.
•
Do not use the Bluetooth feature for illegal purposes (for example, pirating
copies of files or illegally tapping communications for commercial purposes).
18 / 5017 / 4818 / 50

Using the earbuds
18
Wearing the earbuds
Insert the wing tips into your ears and adjust them accordingly to fit your ears.
•
If the touch-sensitive sensor does not make contact with your ear, the earbud
may not work. Use the ear tips that fit your ears if you do not hear a sound
informing you that the earbud is detected.
•
If the earbuds are not positioned correctly in your ears, features like calling
through the earbuds may not work. Use a pair of ear tips that fit your ears and
wear the earbuds properly.
•
Follow all posted warnings and directions from authorised personnel in areas
where the use of wireless devices is restricted, such as aeroplanes and hospitals.
19 / 5018 / 4819 / 50

Using the earbuds
19
1 Hold the upper and lower sides of each earbud and remove them from the charging
case.
2 Check the direction of each earbud.
3 Hold the earbuds with the wing tips facing upwards so that the imprinted direction
marks are exposed, and insert the earbuds into your ears until they fit to your pinnas.
4 Adjust the earbuds by rotating them to the left and right so that they fit comfortably
in your ears.
The touch-sensitive sensors will detect that you are wearing the earbuds when you
put them on. Then, the earbud will emit a sound informing you that the earbud is
detected.
L
20 / 5019 / 4820 / 50