Samsung SDC-435U User manual

Before installing and operating this product,
please read this manual thoroughly.
Super High Resolution UTP Camera SDC-435U User Guide
ENGLISH

This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING : Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
WARNING : To prevent electric shock and risk of fire hazards:
◆Do NOT use power sources other than that specified.
◆Do NOT expose this appliance to rain or moisture.
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and correct input
power voltage. In order to that you can understand this manual thoroughly,
we will explain the model pert numbers.
n SDC-435U SERIES
 •NTSCMODEL •PALMODEL
  SDC-435UN  SDC-435UP
n MODEL DESCRIPTION
 •SDC-435UX
_
 •SIGNALSYSTEM
  N→NTSCMODEL
  P→PALMODEL
SIGNALSYSTEM

COLOR CCD CAMERA User Guide
4
COLOR CCD CAMERA User Guide
5
Contents Features
Excellent Sensitivity
Thebuilt-inhighsensitivityCOLORCCDproducesa
clearimageevenin0.05Lux(COLOR),
0.0001Lux(SENS-UP)orlowerillumination.
Electrical Day&Night
This camera has a function that automatically selects the
modethatisappropriatefordaytimeornight-time
conditions.
TheCOLORmodeoperatesindaytimeconditionsto
provideoptimumcolors,andB/Wmodeoperatesinnight-
time conditions to enhance the definition of the image.
DIS (Digital Image Stabilizer)
TheDISfunctioncompensatesforanycamera
movement, to produce more stable pictures.
Video/DC Drive Lens Support
Communication
YoucanselectVideoorDCDriveLensfromthemenu.
RS-485andCoaxialcommunicationmethodsare
supported.
-RS-485Communications
 :STW(SPD),Pelco-P,Pelco-D,Vicon,Panasonic,
Bosch,Honeywell,SEC
-CoaxialCommunications
 :PelcoCoaxitron
Miscellaneous Functions
HLC(HighLightCompensation),SENS-UP,FLIP(H/
V-REV),D-ZOOM,SHARPNESSandPRIVACYfunctions
are provided.
OSD
Thecamera’sOSDiscomplimentedby18languages.
-NTSC:Korean,English,French,Spanish,Japanese,
Portuguese,Taiwanese
-PAL:English,French,German,Spanish,Italian,
Chinese,Russian,Czech,Polish,Romanian,
Serbian,Swedish,Danish,Turkish,Portuguese
SSNR3 (Samsung Super Noise
Reduction) Function
Thehigh-performanceW-VDSPchipeffectively
removeslow-lightgainnoiseandafterimageto
provide clear images even in dark environments.
High Resolution
Byadoptingadiagonal6mm(1/3")410,000(NTSC)
pixel,470,000(PAL)pixelSONYCCD,thecamera
producesclearpicturequalitywithahorizontal
resolutionof600TVlinesincolor.
SSDR
(Samsung Super Dynamic Range)
Forimageswithhighcontrastbetweenbrightand
dark areas from difficult lighting conditions such as
backlighting, this camera selectively illuminates
darker areas while retaining the same light level for
brighter areas to even out the overall brightness.
UTP TX
OneUTPcabletransmitspowerforthecamera,
videosignalsandRS-485data;installationiseasy
andclean.(EIA/TIA-568B)
Motion Detection
Sincethecameradetectsmotionwithoutany
additional external sensor, you can monitor activity
more efficient.
• Features ………………………………………………………………………… 5
• Warnings & Cautions ……………………………………………………… 6
• Precautions …………………………………………………………………… 7
• Components and Accessories …………………………………………… 9
• Overview ………………………………………………………………………… 9
• Installation …………………………………………………………………… 11
nLENS
 
nSystemDiagram
 
nRJ-45ConnectorSchematicDiagram
 
• Operating your Camera …………………………………………………… 18
nMenuConfiguration  
 nMenuSetup   

•LENS
 

•EXPOSURE
  

•WHITEBALANCE
  

•SSDR
 

•BACKLIGHT
 

•SSNR3
  

•DAY/NIGHT
  

•SPECIAL
  

•EXIT
  
• Troubleshooting ……………………………………………………………… 35
• Specifications …………………………………………………………………… 36

COLOR CCD CAMERA User Guide
6
COLOR CCD CAMERA User Guide
7
SamsungTechwincaresfortheenvironmentatallproductmanufacturing
stages to preserve the environment, and is taking a number of steps to provide
customerswithmoreenvironment-friendlyproducts.TheEcomarkrepresents
SamsungTechwin’swilltocreateenvironment-friendlyproducts,andindicates
thattheproductsatisfiestheEURoHSDirective.
Thisinformationisprovidedtoensureyoursafetyandtopreventanylosses,financialorotherwise.Pleasereadit
carefully and use the product accordingly.
Warnings & Cautions
 *Forproductinquiries,pleasecontacttheretailshopwhereyouboughtthecamera.Theuseofequipmentsuchas
anaerialladderwhileprovidingafter-salesserviceshallbeatyourexpense.
 *Separatethepowerplugduringathunderstorm.
* This product is only part of a surveillance system. Therefore, we can't compensate for material loss and personal
injuries by robbery, fire, natural disaster or something like this type.
Ignoring this information may result in
material loss and serious personal
injuries including death.
Indicates“NeverAllowed.”
Ignoring this information may result in
material loss and a slight injuries.
Indicates“NoDisassembling.”
Warning/Attention/Special Mark Messages
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Do not install under unstable
lighting conditions.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Severe lighting changes or flickering may hinder
normal camera operation.
May lower image quality.Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
Avoid touching the camera lens.
Do not drop the camera or subject
it to physical shock.
May damage the CCD.May cause a product malfunction.
Never keep the camera face to
strong light directly.

COLOR CCD CAMERA User Guide
8
COLOR CCD CAMERA User Guide
9
Precautions
•Exposuretoaspotlightoranobjectemittingstronglightmaycausesmearorblooming.
•Ensurethatthepowersourcecomplieswithnormalspecificationsbeforesupplyingitto
the camera.
Notes
Components and Accessories
1 SuperHighResolutionCameraSDC-435U
2 Autoirislensconnectionplug
3 C-Mountadaptor
4 Instruction manual
5 Powerinputterminalblock
12 3 4 5
Overview
1
5
2
3
4
1CCD protection cap : Please cover the CCD SENSOR when not using it.
2C-Mount adaptor : Please install this adapter when using a C-Mount Lens.
3CS-Mount adaptor : Please remove the C-MOUNT adaptor and then attach it.
4Back Focus clamp screw : Please loosen the clamp screw with a screwdriver before
adjusting the Back Focal length.
5Auto Iris Lens Connector
Front View Side View
Do not expose the camera to rain
or other types of liquids.
Radioactivity exposure may damage the CCD.May cause a product malfunction.Wipe dry any
liquids. Liquids may contain minerals that are
corrosive to electronic components.
Do not expose the camera to
radioactivity.
When connecting cables, be sure to
read the instructions carefully and
follow each step as instructed.
Failure to do so may result in critical system
damage.

COLOR CCD CAMERA User Guide
10
COLOR CCD CAMERA User Guide
11
Overview
Rear View
Bottom View
6Tripod Mounting Bracket Screw Hole
Used to fix the camera on a bracket or tripod.
The screw sizes for this hole are as follows:
1/4"-20UNC(20THREAD)
L:4.5mm±0.2mm(ISOstandard),
or0.197"(ASAstandard)
You can separate the Tripod Mounting Bracket and install it on the
top or bottom of the camera. Make sure to use the Tripod Mounting
Bracket when fixing the camera to a bracket or tripod. Otherwise
the camera may not be secure, or the internal circuitry of the
camera may be damaged.
6
Overview
8Power Supply/Video Output UTP Port
This port accepts power for the camera (AC 24V or AC 28V), outputs video, and
facilitates RS-485 communication. (Refer to P16, UTP Cable)
9Power LED
This lamp is lit when the camera is receiving power normally.
❿Power Input Terminal Block
If the UTP cable cannot be used for power supply (distance over 300m, for example),
this cable is used instead for connecting DC 12V / AC 24V power to the camera.
⓫Video output terminal
Sends video signal and connects to the video input terminal of the monitor.
7Function Setup switch
Display the menu on the screen and move the cursor in four directions to confirm
status or after changing a selected item.
❿
9
7⓫
8
The lens is not supplied with this camera. Purchase a lens suitable for your environment.
This camera accepts the auto iris lens and both C-and CS-mount lens.
•TousethefunctionsofthiscameraeffectivelyitisrecommendedthataDCtypeAutoIris
lens is used.
•Keepthelenssurface clean,ifitbecomes contaminatedwithdirt or fingerprintsthe
picture quality suffers.
Notes
Installation
LENS

COLOR CCD CAMERA User Guide
12
COLOR CCD CAMERA User Guide
13
1. Please take off the CCD protection cap
and C-mount adaptor.
C-mountadaptor
CCDprotectioncap
CS-mountadaptor
When using a CS-Mount lens
• Pleaseusethespecifiedlensconnectionpartsasshowninthepicturebelow.
 The use of the wrong sized parts may cause damage to the inside of the camera or
result in poor fitting.
• Useofalenswhichistooheavyaffectsthebalanceofthe
camera and may cause a malfunction.  Please use a lens
thatweighslessthan450g.
• PleaseselectAv mode ifpossiblewhenadjustingthe
automaticlightcontrol(ALC)ofanautolens.UseofPK
mode may cause hunting.
Notes
C-mountlens:10mmorless
CS-mountlens:5mmorless
2. Please attach the CS-Mount lens to the
camera by screwing it in clockwise.
Installation
When using a C-Mount lens
3. Remove the cover of the auto iris lens connector plug and solder the lens cable to the
connector pin of the plug.
No.3Pin
No.1Pin
Connector
Lenscable
No.4Pin
No.2Pin
LENS
Pin No. DC VIDEO
No.1 Pin Damping - Red (power)
No.2 Pin Damping + NC
No.3 Pin Drive + White (video signal)
No.4 Pin Drive - Black (GND)
4. Please replace the auto iris lens connection plug cover and take off the CCD protection
cap, and then attach the auto iris lens to the camera
by screwing it in clockwise.
5. Please insert the connection plug that is connected to
the auto iris lens cable into the auto lens connector,
which is located on the side of the camera.
Please take off the CCD protection cap and attach the C-Mount lens to
the camera by screwing it in clockwise.
C-mountadaptor
When Using Auto Iris Lens
1. Strip the insulation of the auto iris lens
cable 8mm from the end.
2. Strip the insulation of the core of the auto
iris lens cable to expose a 2mm length.
8mm 2mm

COLOR CCD CAMERA User Guide
14
COLOR CCD CAMERA User Guide
15
Installation
CH1 CH2 CH3 CH4
300m or Less
1.0Km or Less
SCC-3100A
SDC-435U
RS-485
SUP-400 SUR-400
VIDEO
UTP CABLE
BNC CABLE
RS-485
UTP Junction Box Link Setup •Usingtheproductwiththird-partyUTPperipheralsmayresultindegradationofproduct
function and performance.
•Attenuationanddistortioninsignalmayoccurifthemaximumtransmissiondistanceis
exceeded.Please notethatdepending ontheinstallation environment/condition,the
signal may become attenuated and distorted and cause the camera to function
incorrectly even when the transmission distance is within the maximum.
•IfusingRS-485communication, pleaseusetheSTW(SPD),Pelco-P, Pelco-D,Vicon,
Panasonic,Bosch,HoneywellandSECProtocol.
•Ifyouareusingthe1ChPassiveReceiversystemsetup,pleaseconnectthepower
supply directly to the camera.
•Don'tsimultaneouslyconnectbothBNCCABLEandUTPCABLEwithcamera.
Notes
If the distance between the camera and the Junction Box exceeds
300m, please connect an AC 24V or DC 12V power supply to the
Power Input Terminal Block(Accessory). Impressing power when
the maximum transmission distance is exceeded may result in
degradation of picture quality or even camera failure.
1. SDC-435U 4Ch Junction Box 4Ch Receiver DVR/Monitor/Controller
The maximum power transmission distance for the camera is 300m, and the distance
between the camera and the 4ch Receiver cannot exceed 1.0km.
2. UTP Receiver Link Setup(Additional Power input is needed)
SDC-435U  1Ch Passive Receiver  DVR  Monitor
1Ch Passive Receiver
300m or Less
System Diagram

COLOR CCD CAMERA User Guide
16
COLOR CCD CAMERA User Guide
17
Installation
18
81
No. Line Color Camera to Junction Box Junction Box to Receiver
1White+Orange VIDEO (+)
CH1
VIDEO (+) / RS-485 (+)
2Orange VIDEO (-) VIDEO (-) / RS-485 (-)
3White+Green RS485 (+)
CH2
VIDEO (+) / RS-485 (+)
4Blue POWER (-) VIDEO (-) / RS-485 (-)
5White+Blue POWER (+)
CH3
VIDEO (+) / RS-485 (+)
6Green RS485 (-) VIDEO (-) / RS-485 (-)
7White+Brown POWER (+)
CH4
VIDEO (+) / RS-485 (+)
8 Brown POWER (-) VIDEO (-) / RS-485 (-)
No. Line Color Camera to Junction Box Junction Box to Receiver
1White+Orange VIDEO (+)
CH1
VIDEO (+) / RS-485 (+)
2Orange VIDEO (-) VIDEO (-) / RS-485 (-)
3White+Green RS485 (+)
CH2
VIDEO (+) / RS-485 (+)
4Blue POWER (-) VIDEO (-) / RS-485 (-)
5White+Blue POWER (+)
CH3
VIDEO (+) / RS-485 (+)
6Green RS485 (-) VIDEO (-) / RS-485 (-)
7White+Brown POWER (+)
CH4
VIDEO (+) / RS-485 (+)
8 Brown POWER (-) VIDEO (-) / RS-485 (-)
Copper Connector
UTP Coating
The SDC-435U uses UTP cable to receive its power supply (AC 24V or AC28V) from the Junction
Box. Therefore, a separate adaptor is not required. Please refer to the RJ-45 Connector
Schematic Diagram.
UTP CABLE
The camera uses UTP cable for transmitting video signals, power and transferring RS-485
control data.(EIA/TIA-568B)
RJ-45 Connector Schematic Diagram

COLOR CCD CAMERA User Guide
18
COLOR CCD CAMERA User Guide
19
MAIN MENU
1.LENS DC
2.EXPOSURE
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4.To finish the setting, select ‘EXIT’ and press the Function Setup switch.
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT COLOR
8.SPECIAL
9.EXIT SAVE
Selectthefunctionusing
theFunctionSetupswitch.
Changethestatususing
theFunctionSetupswitch.
•Anitemwiththe  icon also has sub menus. To select a sub menu, select an item with
theiconandpresstheFunctionSetupswitch.
Notes
DC/Video : Select Auto Iris Lens
You can adjust the minimum shutter and maximum value of ESC shutter
mode when DC Lens mode is selected.
Using this function, you can control the screen brightness.
1.When the SETUP menu screen is displayed, selectLENSby using the Function Setup
switch so that the arrow indicatesLENS.
2. Select the connected lens type by using the Function Setup switch.
LENS
Operating Your Camera
Function Setup switch
※This operating instruction has been written out as standard by F/W Version 1.0.
MAIN MENU
LENS DC
 VIDEO  MANUAL
EXPOSURE BRIGHTNESS
 SHUTTER  AGC 
SENS-UP RETURN
WHITE BALANCE ATW
 OUTDOOR  INDOOR 
MANUAL  AWC→SET
SSDR OFF
 ON
BACKLIGHT OFF
 BLC  HLC
SSNR3 OFF
 ON
DAY/NIGHT COLOR
 B/W  AUTO
SPECIAL
IMAGE ADJ  MONITOR  CAM TITLE 
SYNC MOTION DET  PRIVACY 
COMM ADJ  LANGUAGE  RETURN
EXIT SAVE
 NOT SAVE  RESET
Use the Function Setup switch whithin the camera.
1. Press the Function Setup switch.
• Main SETUP menu is displayed on the monitor screen.
Menu Configuration
Menu Setup

COLOR CCD CAMERA User Guide
20
COLOR CCD CAMERA User Guide
21
Manual : Select Manual Lens
• WhenusingVIDEOlens,adjust thelensVRexplainedbelowfirst andsetthe focususing
'FOCUSADJ'menu.
• IfcolorrollingoccurswhenusingaDClens,setShuttertoA.FLK.
• Somelensesmaynotworkproperly,dependingonthesettingoftheBRIGHTNESSLEVEL.
•WhenUsingaVideo-TypeAutoIrisLens
❶ AdjusttheALCadjustmentterminalonthelensappropriately.Ingeneral,setittoAV
(Average).
2Itmaynotworkproperlydependingontheinstalledlens.SettheLevelVRofthelens
to the optimal value.
3SetAGCtoOFFandadjusttheLensVRtoanappropriatebrightness.
4AdjusttheLensVR,adjusttheBRIGHTNESS,andthencheckifthescreenbrightness
changesproperly.Otherwise,adjusttheLensVRagain.
Notes
3. Each Lens mode has sub menu items as listed below.
- Brightness (DC, Manual) :Adjusts the video brightness.
- Level (VIDEO) : Adjusts the level of video iris signals; the higher the level,
the brighter the video looks
- FOCUS ADJ (DC, VIDEO) :To adjust the DC and VIDEO lens focus correctly, you must
activate the Focus Settings mode under each lens menu.
Activate the Focus Settings mode, adjust the lens focus, and
then deactivate the settings mode. (The VIDEO lens requires
an extra step: go to the sub menu of the Focus Settings
mode and change the shutter speed to adjust the lens
brightness.)
- IRIS SPEED (DC) : Adjusts the Iris control speed of the DC lens. If the control speed
is too slow or fast, please use this menu to adjust the speed.
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
EXPOSURE
1.When the SETUP menu screen is displayed, select 'EXPOSURE’ by using the Function
Setup switch so that the arrow indicates 'EXPOSURE’.
2. Select a desired mode using the Function Setup switch.
EXPOSURE SETUP
1.BRIGHTNESS 25
2.SHUTTER ESC
3.AGC HIGH
4.SENS-UP OFF
5.RETURN
Operating Your Camera
•WhenyouuseaDClens,settheshuttermodetoA.FLKifcolorrollingoccurs.
•WhentheSHUTTER is settoESCafter selecting theInternalSynchronizationType, the
picture may become unstable if the camera faces a bright fluorescent light. Therefore,
take care when choosing the installation position.
•WhentheSHUTTERissettoMANUALorA.FLKmode,SENS-UPwillbedisabled.
•Anitemwiththe---iconisunavailableduetofunctionsettings.
Notes
SHUTTER :You can select the shutter.
- A.FLK : Select this when you experience picture flicker, which can happen when
there is a clash with the frequency of the installed lighting.
- ESC : Select this to control the shutter speed automatically. If ESC is selected,
the shutter speed is automatically controlled depending on the ambient
illumination of the subject.
- MANUAL :You can control shutter speed manually. (1/60(1/50) ~ 1/120,000)
- --- : Shutter speed is fixed at 1/60sec(1/50sec).

COLOR CCD CAMERA User Guide
22
COLOR CCD CAMERA User Guide
23
Operating Your Camera
AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but
the higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 32dB.
- HIGH : Allows automatic gain control from 5.3dB to 37dB.
SENS-UP :When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO :Activates the SENS-UP function.
•Ifyou pressthe FunctionSetupswitchin‘AUTO’mode,You canadjust brightnessby
increasingordecreasingtheshutterspeed.(x2~x512)
•Notethatthehigherthezoomlevel,thebrighterthescreen,butthemorelikelyitisthatan
after-imagewillappear.
•AlthoughNoise,Spots,andWhitishsymptomsmayoccurinSENS-UPoperationwhenthe
zoomlevelisincreased,thisisnormal.
Notes
Use the White Balance function to adjust the screen color.
1.When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function
Setup switch so that the arrow indicates ‘White Bal’ .
2. Select a desired mode using the Function Setup switch.
White Bal (White Balance)
Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,700˚K and
11,000˚K.
OUTDOOR : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)
INDOOR :
Select this when the color temperature is between 4,500˚K and 8,500˚K.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by
using the ATW or AWC mode.After that switch to MANUAL mode, fine-
tune the White Balance and the Function Setup switch.
AWC SET :
To find the optimal luminance level for the current environment, point the
camera towards a sheet of white paper and press the Function Setup switch. If
the environment changes, readjust it.
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
•WhiteBalancemaynotworkproperlyunderthefollowingconditions.Inthiscaseselect
theAWCmode.
❶ When the color temperature of the environment surrounding the subject is out of the
control range (e.g. clear sky or sunset).
2
When the ambient illumination of the subject is dim.
3
 If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
Notes
RETURN : Select this to save the changes in the EXPOSURE menu and return to the
SETUP menu.

COLOR CCD CAMERA User Guide
24
COLOR CCD CAMERA User Guide
25
SSDROFF
Operating Your Camera
BACKLIGHT
Unlike conventional cameras, the SDC-435U is designed so that it delivers a distinctive
subject and background at the same time, even when the subject is in backlight, by
adopting a function of the proprietary W-V DSP chip.
1.When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates ‘BACKLIGHT’.
2. Select a desired mode using the Function Setup switch depending on the camera purpose.
BLC :
Enables a user to select a desired area on a picture and view that area more clearly.
- LEVEL :Adjust level of the BLC function.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the area to be enhanced.
BLCON BLCOFF
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
HLC (High Light Compensation) :
If the scene contains extremely brightly light areas such as; from car headlight, the
light can mask out much of the on-screen detail.
- LEVEL :Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / brightness of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT :Adjust the area to be enhanced.
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
SSDR (Samsung Super Dynamic Range)
SSDR illuminates darker areas of an image while retaining the same light level for brighter
areas to even out the overall brightness of images with high contrast between bright and
dark areas.
1.When the SETUP menu screen is displayed, select ‘SSDR’ by using the Function Setup
switch so that the arrow indicates ‘SSDR’.
2. Use the Function Setup switch to change the SSDR level in the sub menu according to
the contrast between bright and dark areas.
SSDRON

COLOR CCD CAMERA User Guide
26
COLOR CCD CAMERA User Guide
27
Operating Your Camera
3. Select a desired mode using the Function Setup switch.
•BecausetherecanbeadifferenceintheeffectivenessofHLCaccordingtotheamountof
lightareainthescreen,optimizetheinstallationangleforthebestHLCperformance.
•Whendark,the HLC isonlyactivated when abrightlight exceedingaspecificsize.(In
NIGHTONLYmode).
•TheHLCisnotactivatedindaylightorwhenbrightlightisnotpresentatnight.(InNIGHT
ONLYmode).
Notes
Select ‘BLC’ to adjust the area to be
enhanced then adjust the level.
HLC : Enable the user to change the level,
limit, mask color/tone and area.
This function reduces the background noise in a low luminance environment.
1.When the SETUP menu screen is displayed, select ‘SSNR3’ by using the Function Setup switch
so that the arrow indicates ‘SSNR3’ .
2. Select a desired mode using the Function Setup switch.
OFF : Deactivates SSNR3. Noise is not reduced.
ON :Activates SSNR3 so that noise is reduced.
SSNR3
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT COLOR
3. Set the SSNR3 mode to ‘ON’ and press the Function Setup switch. Then you can adjust the
noise reduction level.
•YoucannotsettheSSNR3to‘ON’or‘OFF’whentheAGCmodeoftheEXPOSUREmenuis
‘OFF’.
•WhenadjustingthenoisereductionlevelintheSSNR3mode,rememberthatthehigher
the level set, the more the noise level will be reduced, as will the brightness of the image.
Notes
OFF : Not being used

COLOR CCD CAMERA User Guide
28
COLOR CCD CAMERA User Guide
29
Operating Your Camera
•WhenusingaVideoAuto IrisLens,ifyousetthe lenslevel tolow,automaticswitching
betweenColorandBlack&Whitemaynotoccur.
•WhenAGCintheEXPOSUREmenuis'OFF','---'modeoperatesaslikeselecting'COLOR'
modeand'AUTO'modecannotbeselected.
Notes
1.When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup
switch so that the arrow indicates ‘SPECIAL’.
SPECIAL
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT COLOR
8.SPECIAL
9.EXIT SAVE
SPECIAL
1. IMAGE ADJ
2. MONITOR LCD
3. CAM TITLE OFF
4. SYNC INT
5. MOTION DET OFF
6. PRIVACY OFF
7. COMM ADJ
8. LANGUAGE ENGLISH
9. RETURN
2. Select a desired mode using the Function Setup switch.
You can display pictures in color or black and white.
1.When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function
Setup switch so that the arrow indicates ‘DAY/NIGHT’.
DAY/NIGHT
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT COLOR
8.SPECIAL
2. Select a desired mode using the Function Setup switch according to the picture display you want.
COLOR : The picture is always displayed in color.
B/W :The picture is always displayed in black and white.
You can turn on or off the burst signal on B/W mode.
AUTO :The mode is switched to ’Color‘ in a normal
environment, but switches to ’B/W‘ mode
when ambient illumination is low. To set up
the switching time for AUTO mode, press the
Function Setup switch.
You can turn on or off the burst signal on
B/W mode.
- DWELL TIME :You can select day/night switching delay
time from. 
5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
IMAGE ADJ :
1) When the SPECIAL menu screen is displayed, select ‘IMAGE ADJ’ by using the
Function Setup switch so that the arrow indicates ’IMAGE ADJ‘.

COLOR CCD CAMERA User Guide
30
COLOR CCD CAMERA User Guide
31
Operating Your Camera
CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the
FRONT DOOR
arrow indicates ‘CAM TITLE’.
2) Set it to ‘ON’ by using the Function Setup
switch.
3) Press the Function Setup switch.
4) Use the Function Setup switch to move
to a desired letter and select the letter by
pressing the Function Setup switch.
Repeat this to enter multiple letters. You
can enter up to 15 letters.
5) Enter a title, move the cursor to ‘POS’ and press
the Function Setup switch. The entered title
appears on the screen. Select the position to
display the title on the screen by using the
Function Setup switch and press the Function
Setup switch. When the position is determined,
select ‘END’ and press the Function Setup
switch to return to the SPECIAL menu.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
CLR POS END
•WhentheCAMTITLEmenuis‘OFF’,notitlewillbedisplayedonthemonitorscreeneven
if you enter one.
•OnlyEnglishisavailableinthismode.
•If youmove thecursor toCLRandpresstheFunctionSetupswitch, allthe lettersare
deleted. To edit a letter, change the cursor to the bottom left arrow and press the
FunctionSetupswitch.Movethecursoroverthelettertobeedited,movethecursorto
thelettertobeinsertedandthenpresstheFunctionSetupswitch.
Notes
 •V-REV : You can flip the picture vertically on the screen.
 •H-REV :You can flip the picture horizontally on the screen.
 •D-ZOOM : You can use a digital zoom of x1 ~ x16.
 •DIS (Digital Image Stabilizer) :This function mitigates any picture movement due to
external factors such as wind.
 •FONT COLOR : You can change the OSD font color. (White,Yellow, Green, Red, Blue)
 •SHARPNESS :As you increase this value, the picture outline becomes stronger and
clearer.Adjust this value appropriately depending on the sharpness of
the picture.
 •RETURN : Select this to save the settings for the IMAGE ADJ menu and to return
to the SPECIAL menu.
•WhentheV-REVorH-REVmodeisenabled,thetextonthescreendoesnotflip.
•If youincreasethe  SHARPNESS level toohigh, the picture maybecomedistortedor
noise may appear.
•DISdoesn’toperatewhenbackgroundilluminationistoolow.
•DISdoesn’toperatewhenobjectpatternismonotonicaslikeskyorwhitewall.
Notes
Monitor : Please change the settings value of video
appropriate to your monitor.
- LCD : Please select this menu item when using an
LCD monitor.
You can change the gamma, PED level and
color gain in the sub menus.
- CRT : Please select this menu item when using a CRT
monitor.
- USER : Please use this menu item when using a monitor other than standard ones. You can
change the gamma, PED level and color gain in the sub menus.
IMAGE SETUP
1. V-REV OFF
2. H-REV OFF
3. D-ZOOM OFF
4. DIS OFF
5. FONT COLOR WHITE
6. SHARPNESS ON
7. RETURN
2) Select a desired mode using the Function Setup switch.

COLOR CCD CAMERA User Guide
32
COLOR CCD CAMERA User Guide
33
MOTION DET :
This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen,
and the words 'MOTION DETECTED' appear on the
screen when movement is detected.
You can monitor activity more efficient.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicatesMOTION DET.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas.When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small
movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILLSET : Fills in a selected MD area. The color of filling is sequentially selected
• WhenusingACpowerat60Hz(NTSC),50Hz(PAL)frequency,youcanusetheL/Ltype
synchronization.
•WhenthepowerisDC12V,theSYNCmenuisfixedtothe‘INT’mode.
•WhenusingRJ-45Connector,youcan'tusetheL/Ltypesynchronization.
Notes
PRIVACY : Mask an area you want to hide on the screen.
PRIVACY AREA SETUP
1.AREA AREA1
2.MODE OFF
3.MASK COLOR GREEN
4.MASK TONE 1
5.TOP 39
6.BOTTOM 79
7.LEFT 13
8.RIGHT 52
9.RETURN
Operating Your Camera
SYNC : In areas where the supply is at 60Hz(NTSC),
50Hz(PAL) frequency, you can synchronize the
output phase of multiple cameras using the
power synchronization function (Line-Lock)
without using a synchronization signal generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
as brown, orange, blue, cyan, green, yellow, magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the
SPECIAL menu.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that
the arrow indicates ‘PRIVACY’.
2) Set up the mode using the Function Setup switch.
- AREA : You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA.
- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black,White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL
menu.
COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling the camera
through an external control device.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that
the arrow indicates ‘COMM ADJ’.
2) Set up the mode using the Function Setup switch.

COLOR CCD CAMERA User Guide
34
COLOR CCD CAMERA User Guide
35
Operating Your Camera
Select a desired EXIT mode using the Function Setup switch depending on the camera
purpose.
- SAVE : Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET :Resets the camera settings to the factory defaults. Communication,
Language and Monitor settings are not initialized.
EXIT
Troubleshooting
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
● Nothing appears on the screen.
▶Check that the power cord and line connection between the camera and monitor are fixed
properly.
▶Check that you have properly connected UTP cable or BNC cable to the camera.
▶Check the type of lens.
▶Check the pin arrangement for the UTP cable.(EIA/TIA-568B)
● The image on the screen is dim.
▶Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶Set the camera to the correct monitor setting.
▶If the camera is exposed to too strong light, change the camera position.
● The image on the screen is dark.
▶Adjust the contrast feature of the monitor.
▶If you have an intermediate device, set the 75Ω/ Hi-z properly.
● The camera is not working properly, and the surface of the camera is hot.
▶Check that you have properly connected the camera to an appropriate power source.
● The SENS-UP function does not work.
▶Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
● The Motion Detection function does not work.
▶Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
● Color is not correct.
▶Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶Ensure the camera is not pointing towards the sun.
● When coaxial communication is not available:
▶Make sure that the camera and monitor are installed within the recommended distance.
▶ Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded.
● Picture is distorted.
▶ Check the length of the UTP cable (1km or less).
● The camera does not work, and the video feed from the camera is not being received.
▶Check the Junction Box to see whether the connection status and pin arrangement for the
camera's UTP cable and the Camera Input UTP cable are normal.
LANGUAGE : You can select the menu language according to your requirements.
RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
- CAM ID : Determines the camera's identification
number (between 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/
38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for
the parity bits.
- RET PKT : Determines whether to send a command
back to the controller device when a
communication control command is sent to the camera.
- DISP ID : Display camera title on top left corner of the screen.
- PROTOCOL : Select the communication PROTOCOL.
(STW(SPD) / PELCO-D / PELCO-P / BOSCH / HONEYWELL / VICON / SEC/
PANASONIC)
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
* Initial value of communication adjustment
Item Camera ID BAUD RATE UART MODE PET PKT
Initial value 19600 8-NONE-1 ENABLE

COLOR CCD CAMERA User Guide
36
COLOR CCD CAMERA User Guide
37
Specifications
DECLARATION OF CONFORMITY
ApplicationofCouncilDirective(s) 89/336/EEC
Manufacturer'sName SAMSUNGTECHWINCO.,LTD
Manufacturer'sAddress SAMSUNGTECHWINCO.,LTD
 42,SUNGJU-DONGCHANGWON-CITY,
 KYUNGNAM,KOREA,641-716
EuropeanRepresentativeName
EuropeanRepresentativeAddress
EquipmentType/Environment CCTVCamera
ModelName SDC-435UP
BeginningSerialNO. C10SA010007
YearofManufacture 2009.10.01
Conformanceto EN50081-1:1992
 EMC-Directive89/336EECand92/31/EEC
 EN50130-4:1996
We, the undersigned, hereby declare that the equipment specified above conforms
totheaboveDirective(s).
Manufacturer SAMSUNGTECHWINCO.,LTD LegalRepresentativeinEurope
Signature  Signature
FullName BONJENGGU FullName
Position QUALITYCONTROLMANAGER Position
Place CHANGWON,KOREA Place
Date 2009.10.01 Date
The specification for this product may change without prior notice for product improvement.
This specification is based on a transmission distance of 500 meters; in cases of long-distance
transmissions, some degradation in picture quality may occur depending on the operating environment.
SDC-435UN SDC-435UP
ELECTRICAL
Input Voltage AC 24V ±10% / AC 28V ±10% / DC12V±10%
Power Consumption Max 3.5W
VIDEO
Imaging Device 1/3 inch, Diagonal 6mm Super HAD CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Scanning System 2:1 Interlace
Synchronization Internal / Line-Lock
Frequency H : 15.734KHz / V : 59.94Hz H: 15.625KHz / V: 50.00Hz
Horizontal Resolution 600TVL
Min. Illumination 0.05 Lux (50IRE, @F1.2), 0.0001Lux (SENS-UP, x512)
S/N (Y Signal) 52dB (Weight On, AGC OFF)
Video Output CVBS : 1.0Vp-p, 75Ω composite
UTP Output Built-in UTP TX (Maximum transmission length 1.0Km) : Balanced differential signal 100Ω
OPERATIONAL
Electronic Shutter Speed 1/60sec~1/120ksec 1/50sec ~ 1/120ksec
On Screen Display NTSC : 7 Languages, PAL : 15 Languages
SSDR ON / OFF (Level adjustable)
Backlight Compensation BLC / HLC / OFF
Day & Night COLOR / B/W / AUTO
Gain Control LOW / HIGH / OFF
White Balance ATW / OUTDOOR / INDOOR / MANUAL / AWC (1,700°K ~ 11,000°K)
SENS-UP Auto / OFF (Selectable x2 ~ x512)
Motion Detection ON / OFF (8 Programmable zones)
Privacy Masking ON / OFF (12 Programmable zones)
SSNRIII ON / OFF (Level adjustable)
Digital Zoom ON / OFF (x1 ~ x16)
DIS ON / OFF
Camera Title ON / OFF (Display 15 Characters)
Sharpness ON / OFF (Level adjustable)
Flip / Mirror ON / OFF
Coaxial Communication Pelco Coaxitron
RS-485 Communication STW, Pelco-D, Pelco-P, BOSCH, Honeywell, SEC, PANASONIC, VICON
ENVIRONMENTAL
Operating Temperature / Humidity -10°C ~ +50°C / 30% ~ 80% RH
MECHANICAL
Lens Mount C / CS Mount
Back Focus Adjustment Manual
Dimension / Weight 58(W) x 52(H) x 121(D) / 290g

COLOR CCD CAMERA User Guide
38
COLOR CCD CAMERA User Guide
39
MEMO MEMO