Samsung AC-505CM Series Manual

LED R&D Lab(VD)
LED Display Install Manual
IAC Series
LH015IAC***
Ver. 0.3

LED R&D Lab(VD)
1
Revision History
Version Date (Y/M/D) Description
0.1 2023/06/01 Release ver 0.1
0.2 2023/06/12 Modification Side by Side Content (P114~118)
Delete Side by Side Screen Split scenario #2 (P119)
0.3 2023/06/15 Add checking CABINET number (BNV20231FE9) (P18,20)

LED R&D Lab(VD)
2
1. Product and installation information
2. Preparation of Cabinet installation
3. Wall Mount
4. Frame installation and cable connection
5. Frame Bezel Installation
6. Dehumidification mode guide
7. IP Manual setting Guide
※ Appendix1 -LED MODULE and CIRCUIT replacement method
※ Appendix2 –System Main / TCON / LED Module Update data on replacement
※ Appendix3 –Side by Side installation
※ Appendix4 –LSM connection
※ Appendix5 –Gradation Calibration (SSA)
※ Appendix6 –Framelock mode support timing table
Table of contents

LED R&D Lab(VD)
3
MODEL Product appearance and information
IAC series
REMARK IAC Series : Package Type / 60 Hz Refresh Rate
◆Model specification
-This manual is an installation manual for IAC and can be applied to the model below.
1. Product and installation information

LED R&D Lab(VD)
4
◆Model specification (IAC)
Specifications
130”
P1.5
CABINET
Size
(mm)
Horizontal 2888.55
vertical 1628.55
Resolution
(Pixels)
Horizontal 1920
vertical 1080
Module (EA) 27 X 4 (108)
weight (kg)
(Cabinet) 16.0
SET weight (kg) 124.55
Packing weight (kg) 78.9
Power consumption (W) Typical 685W (Max 1660W)
Luminance (nit)
Max 500
Peak 1000
1. Product and installation information

LED R&D Lab(VD)
5
◆Cabinet product information
1628.55
62.2
130”
2888.55
1. Product and installation information

LED R&D Lab(VD)
6
◆Installation precautions (LED damage)
precautions Image
[External impact, fall caution]
1 Remove the cover-corner of the product before installation and do not
impact the LED surface or drop it on the floor.
2 Do not place the product on the vibrator and do not place the LED
surface facing the floor.
3 Make sure that the edge of the LED module is not damaged by external
contact.
4 Do not load more than 12 steps.
① ②
③ ④
[Watch out for LED damage caused by static electricity]
▶Do not work by touching the LED surface with hands without gloves.
[Caution of LED damage caused by metal]
▶Be careful not to get metal on the front of the LED.
▶When attaching the metal, separate the module and remove it using a
magnet.
MODULE
Front
metal
1. Product and installation information

LED R&D Lab(VD)
7
precautions Image
[Caution of LED damage caused by liquid]
When water or various chemicals touch the LED, the inside of the LED may be damaged.
①Water, dew, air conditioner condensate, sprayer, sweat, and saliva do not directly touch the
product.
-Be careful not to sweat on the product. (※ Maintain proper temperature so as not to sweat)
-Be careful not to spit on the product, and it is recommended to wear a mask.
②The following substances should not be directly in contact with the product, and
the case of exposure of the steam to the product should be minimized.
-Detergent or disinfectant : carpet cleaning detergent, glass cleaner, 84 disinfectant, etc.
(※ When cleaning the floor or wall with detergent or water, it is recommended to install a screen so that it does not touch the
product)
-Various chemicals: paints, mosquito repellents, cinnabar, benzene, toluene, solvents, surfactants, halogens (chlorine, bromine),
and substances containing these ingredients;
③If liquid touches the product
-If there is water on the product, turn off the product immediately, dry it enough for more than a day, and run the
dehumidification mode to remove moisture from the LED. (※ P74, refer to "Dehumidification mode using LSM")
-If there is any liquid other than water on it, remove it with alcohol and run the dehumidification mode.
[Precautions related to construction]
①In the case of installation at the construction site, the product must be installed after construction and
cleaning are completed.
②If the product is under construction in the installed space, take the following measures.
-Shielding film should be installed to protect the product by sealing the entire product so that it is not exposed to dust and
various liquids.
-Operates a video or 100 gray scale white for more than 2 hours every day.
-After the construction is completed, remove enough dust, various liquids, and steam, remove the shield, and execute the
dehumidification mode.
카펫
클리너 유리
세정제
Taping Shielding film
84
Disinfectant
※ Only use for IWA
◆Installation precautions (LED damage)
1. Product and installation information

LED R&D Lab(VD)
8
◆Heat dissipation guide
Installation condition
-Conditions for using SAMSUNG WALL MOUNT
-Solar direct sunlight conditions cannot be installed (including glass window passage conditions)
-It is recommended to use room temperature below 25°C
-Effect of Cold/Hot Air Conditioning System
-When cold / hot air is the same air conditioning system,
∙Be careful not to let the warm air touch the product.
-Outside temperature measurement position
Measured at a distance of 300mm from the center of the product
Air vent aperture ratio
-use mesh type air vent
-If the aperture ratio is not 100%, the separation distance =
Minimum distance
aperture ratio(%) /100
-aperture ratio (%) =    .  ℎ
  
※ It is written based on Full white, back light 7
Video, created based on back light 10
A
B
d
c
wall
Outside
temperature
measurement
position
300mm
1. Product and installation information

LED R&D Lab(VD)
9
•Vertical wall installation (if Fan is not applied)
WALL
Air vent area
minimum 30mm
set ~ ceiling
set ~ floor
1. Product and installation information
minimum 30mm

LED R&D Lab(VD)
10
•Vertical landfill installation (when Fan is not applied)
Air vent area
At least 30mm (opening rate 100%)
At least 30mm (opening rate 100%)
Recommended conditions: 500mm or more
set ~ floor
Recommended conditions: 500mm or more
set ~ ceiling
WALL
If the aperture ratio is not 100%, the separation distance =
Minimum distance
aperture ratio(%) /100
1. Product and installation information

LED R&D Lab(VD)
11
•Precautions for Landfill Installation
150mm left and right space is required for service. (Fig.1)
Fixed screws are placed inside. , it is necessary to secure a field of view of about 150mm. (Fig. 2)
* Like heat dissipation specifications, space of 30mm or more is required up and down
WALL
150mm 150mm
150mm
Need space for side screw positioning
Work with a fist driver
Fig.1 Left and right spaces over 150mm Fig.2 working guide
Minimum 30mm or more
1. Product and installation information

LED R&D Lab(VD)
12
◆Setup ready
•It is provided for Set accessories.
x2
BRACKET-LINK
(BN61-18825A)
ASSY COVER P-DECORATION
(BN96-57387A~57390A, and
BN96-57380B)
ASSY ACC-WALL MOUNT
(BN96-54014L) ASSY ACC-WALL MOUNT
(BN96-54014M)
ASSY COVER P-HANDLE
BN96-55707A
1. Product and installation information
(-) (+) driver
Electric driver
※ Recommended Specifications
PROTECTION JIG
BN81-17515B

LED R&D Lab(VD)
13
◆Cabinet Accessories
SMPS SVC
BN44-01160A
T-CON SVC
BN94-18201A
WALL MOUNT ACC
BN96-54014L/M SVC MODULE (6EA)
BN94-18204A
ACC MANUAL CABLE
BN96-57518U
BRACKET-LINK
BN61-18825A
1. Product and installation information
Quick setup guide Product warranty
(It is not provided in some areas. ) Specification guide ASSY COVER P-DECORATION
(BN96-57387A~57390A, and
BN96-57380B)

LED R&D Lab(VD)
14
▶Connection structure: Connect the signal cable (OCM) and power cable between
P-FRAME and Front P-FRONT
1) P-FRAME Left/Right Connection
-Power unit on cable connection between AC Inlet Boards
-Connect the left/right cable of the speaker
2) Cable connection between P-FRAME + P-FRONT
-Connect four OCM cables to the Main Board Video output port
→ Form the OCM cable according to each P-FRONT location and connect it to the Lower Board
OCM connector at the bottom of the P-FRONT.
-Connect the SMPS output cable and the screen power input cable from the P-FRONT.
□Features when configuring the Screen( Different specifications compared to the existing ones )
1. Product and installation information

LED R&D Lab(VD)
15
1. Product and installation information
2. Preparation of Cabinet installation
3. Wall Mount
4. Frame installation and cable connection
5. Frame Bezel Installation
6. Dehumidification mode guide
7. IP Manual setting Guide
※ Appendix1 -LED MODULE and CIRCUIT replacement method
※ Appendix2 –System Main / TCON / LED Module Update data on replacement
※ Appendix3 –Side by Side installation
※ Appendix4 –LSM connection
※ Appendix5 –Gradation Calibration (SSA)
※ Appendix6 –Framelock mode support timing table
Table of contents

LED R&D Lab(VD)
16
2. Preparation of Cabinet installation
◆Pre-prepare before installation
①To remove SET packaging, a ceiling space 600mm higher than the minimum SET packaging is required.
②If there is not enough space, disassemble the SET packaging in the possible space
and move the cabinet to the installation space.
Fig.1 Packing disassembly space
SET packing
Ceiling wall
1982mm
600 +@ mm
PALLET

LED R&D Lab(VD)
17
LED set
Box
Top-Cushion
Bottom-Cushion
Accessory
Left2
Left1
Right1
Right2
2. Preparation of Cabinet installation
◆Pre-prepare before installation
①Remove the tape of the top BOX and open it. (Fig.2)
②Remove the top–cushion.
③Check the set status. (Two rear parts and four front parts) (Fig.3)
Fig.1 Packing Fig. 2 Packing out Fig.3 check the SET
There are number of cabinet

LED R&D Lab(VD)
18
Fig.5 remove Cover Corner
Al-Bag
Bag Zipper open
SCREW POINT
PAD
When moving the module, two people move
the module vertically as shown in the figure
above.
side VIEW
2. preparation of Cabinet installation
④Open the bag shielding of the front module. Hold the internal COVER-CORNER, take out the set, and
open the AL-Bag and disconnect the AL screws (4 in total). (Fig.4)
⑤Disconnect the screw of the COVER-CORNER part. (4 locations) (Fig.5)
※ When removing the cover-corner, install the white PAD without disassembling it to prevent damage to the front module.
◆Pre-prepare before installation
Fig.4 Before screen check,
remove PAD and attach SPACER-EVA
Carefully place the module on the PAD.

LED R&D Lab(VD)
19
⑥Remove some of the HOLDER-PCB materials assembled in the cabinet.
(Refer to the removal point in the next PAGE)
※ Be careful because the location of the HOLDER-PCB that must be removed is different for each cabinet number!
Screw point
HOLDER-PCB
Remove the HOLDER-PCB by loosening the screw.
2. preparation of Cabinet installation
◆Pre-prepare before installation