Samsung AE BXYD Series Installation instructions

2
AE***BXYD*G
No Parts Procedure Remark
1 CABI SIDE RH You must turn off the power before
disassembling.
1) Unscrew and remove 3 screws on the CABI
SIDE RH.
(Use '+' type screw driver)
2) Hold CABI SIDE RH handle and push to
downside. Pull the left side of Cabinet and
remove it.
hook
hook
Repairs must be carreid out by trained professional.
For any repairs, please contact our service provider or independent qualified professional.
Disassembly and Reassembly

3
No Parts Procedure Remark
2 COVER FRONT 1) Unscrew and remove 3 screws on the COVER
FRONT.
(Use '+' type screw driver)
2) Hold Top and Bottom of the COVER FRONT
and push it to right side.
1
2
3
1
2
3

4
No Parts Procedure Remark
3 CABI FRONT RH 1) Unscrew and remove 3 screws on
the CABI FRONT RH.
(Use '+' type screw driver)
2) Hold the handle and pull the right-bottom side
of cabinet.
3) Remove the CABI FRONT RH to downside.
hook
hook
4 GUARD FAN *You can remove the GUARD FAN for the first
time.
1
2
1
2
1) Unscrew and remove 5 screws on the GUARD
FAN.
(Use '+' type screw driver)
2) Remove it to up and left side.
Disassembly and Reassembly

5
No Parts Procedure Remark
5 CABI TOP *You can remove the CABI TOP before
disassembling GUARD FAN.
1) Unscrew and remove 9 screws on the CABI
TOP.
(Use '+' type screw driver)
1
2
1
2

6
No Parts Procedure Remark
6 CABI BACK RH *You can remove the CABI BACK RH before
disassembling CABI TOP.
1) Unscrew and remove 1 screw.
Remove the temperature sensor.
2) Unscrew and remove 10 screws on the CABI
BACK RH.
(Use '+' type screw driver)
(If water pipe is connected, you don't have to
remove yellow points)
(If water pipe is connected, you don't have to
remove CABI BACK LOW)
hook
Disassembly and Reassembly

7
No Parts Procedure Remark
7 CABI FRONT LF 1) Unscrew and remove 7 screws on the CABI
FRONT LF.
(Use '+' type screw driver)
8FAN 1) Turn the one nut as shown in the picture and
remove it.
(Use right size of the wrench)
2) Remove the nut.
(Use the Wrench)
3) Remove the fan.

8
No Parts Procedure Remark
9MOTOR 1) Disconnect the motorwire from the Inverter
PBA.
2) Loosen the 3 Holderwire points which are
fixing the motorwire (yellow points).
3) Unscrew and remove 4 motor screws.
10 BRACKET MOTOR 1) Unscrew and remove 2 screws on the BRACKET
MOTOR.
(Use '+' type screw driver)
Disassembly and Reassembly

9
No Parts Procedure Remark
11 HEATER 1) Unscrew and remove 4 screws on the HEATER.
(Use '+' type screw driver)
2) Unscrew and remove 1 screw on the COND &
BASE
3) Unscrew and remove 2 screws on the
BRACKET MOTOR TOP and remove it from the
Cond.
4) Pull the COND and move 2EA COND SUPPORT
like right pircture.
5) Remove the heater.

10
No Parts Procedure Remark
12 CONTROL OUT [INVERTER PBA]
1) Disconnect 2connectors from the Inverter PBA
2-1) If model code is AE***BXYDEG, Unscrew and
remove 6 screws with Heatsink.
2-2) If model code is AE***BXYDGG,
Unscrew and remove 2 screws with Heatsink.
3) Unscrew and remove 2screws
[EMI PBA]
1) Unscrew and remove 8screws
[MAIN PBA]
1) Disconnect connectors from the Main PBA.
2) Unscrew and remove 4 screws.
INV PBA
EMI PBA
AE***BXYDEG
AE***BXYDGG
MAIN PBA
Disassembly and Reassembly

11
No Parts Procedure Remark
13 COMPRESSOR 1) Remove the all COMP FELT
- Comp felt top
- Comp felt out
- Comp felt
2) Remove the COMP CASE.
3) Unscrew and remove 4 nuts.
4) Seperate the pipes from the Comp
(3 yellow points)