Samsung SyncMaster 763MB User manual

www.sec.co.kr/monitor 접속 후고객등록을 해주세요.
매월 추첨을 통해 사은품을 드리겠습니다.
자세한 내용은 홈페이지나 사용설명서 고객등록 페이지를 참고하세요.
SyncMaster 763MB/765MB

Index
Main Page
Notational
Power
Installation
Clean
Other
Introduction
Unpacking
Front
Rear
Setup
Troubleshooting
Check List
Q & A
Self-Test Feature Check
Specifications
General
PowerSaver
Preset Timing Modes
Information
Service
Terms
Regulatory
Natural Color
Authority
Safety Instructions
Connecting Your Monitor
Installing the Monitor Driver
Bottom
Base Installation

Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited Important to read and understand at all times
Do not disassemble Disconnect the plug from the outlet
Do not touch Grounding to prevent an electric shock

Power
When not used for extended periods of time, set your PC to DPMS. If using
a screen saver, set it to the active screen mode.
?If the size of your monitor is small, or if the same image is present for
long periods of time, you may see afterimages due to damage to the
fluorescent substance on the inside of the CDT.
Do not use a damaged or loose plug.
?This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
?This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
?An improper ground may cause electric shock or equipment
damage.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
?Failure to do so may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it
is not used for a long period of time.
?Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
?This may cause a fire.

Installation
Do not cover the vents on the monitor cabinet.
?Bad ventilation may cause a breakdown or fire.
Put your monitor in a location with low humidity and a minimum of
dust.
?An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
?This may cause damage to the product or human body.
Place the monitor on a flat and stable surface.
?The monitor can cause injury by falling.
Set down the monitor carefully.
?It could be damaged or broken.
Do not place the monitor face down.
?The CDT surface may be damaged.
Do not use the monitor without the monitor stand.
?It could break down or cause a fire due to bad ventilation.
?
If the monitor must be used without the supplied stand, take steps
to insure proper ventilation.

Clean
When cleaning the monitor case or the surface of the CDT, wipe with a
slightly moistened, soft fabric.
Do not clean Flat monitor with water. Use a water-diluted mild detergent.
(Some detergents contain significant amounts of alcohol-based solvents,
which can damage (color change) or crack the monitor case. The
antiglare/anti-static surface coating on the CDT may also be affected.)
Dilute the detergent (1:10 ratio) with water before using.
Do not spray detergent directly on the monitor.
Use the recommended detergent with a smooth cloth.
?You can prevent the coated CDT from being damaged or the
monitor cabinet from being dissolved, cracked or discolored.
?You can buy a recommended detergent at any Samsung Service
Center.
If the connector between the plug and the pin is dusty or dirty, clean it
properly with a dry cloth.
?A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects on
the monitor.
?This may cause damage, electric shock or a fire.
?If a foreign substance gets into the monitor, disconnect the plug
and thencontact a service center.

Other
Do not remove cover(or back). No user serviceable parts inside.
?This may cause an electric shock or a fire.
?Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are
any unusual sounds or smells coming from it - unplug it immediately
and contact an authorized dealer or service.
?This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor.
?This may cause an electric shock or a fire.
For each hour of looking at the monitor, you should let your eyes rest
for 5 minutes.
?This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
?This may cause an explosion or fire.
Do not try to move the monitor by pulling on the wire or the signal
cable.
?This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
?This may cause a breakdown, electric shock or a fire due to
damage to the cable.

Other
Never insert anything metallic into the monitor openings.
?This may cause an electric shock, fire or injury.
Keep the monitor away from any magnetic substances.
?This may cause discoloring or distortion of the image.

Unpacking
Monitor and Stand
(Some models include a stand attached. )
Please make sure the following items are
included with your monitor. If any items are
missing,
contact your dealer.
Power Cord
Stand
Quick Setup Guide
Warranty Card
(Not available in all locations)
User's Guide and
Driver Installation CD

Front
SyncMaster 763MB
1. MagicBright button Use this button to control the MagicBright.
2. Exit button Use this button to Exit the active menu or the OSD.
3. Adjust buttons These buttons allow you to highlight and adjust items in the menu.
4. Menu button Use this button to open the OSD and activate a highlighted menu item.
5. Power indicator This light glows green during normal operation, and blinks green once
as the monitor saves your adjustments.
6. Power button Use this button to turn the monitor on and off.
Note: See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when
leaving it unattended for long periods.

Front
1. 하이라이트 버튼 하이라이트기능이 나타나게 할 때 누릅니다.
2. 종료/MagicBright 버튼 메뉴화면을 사라지게 할 때나 MagicBright 조정을 할때 누릅니다.
3. 조정 버튼 메뉴화면에서 상하좌우로 움직여 메뉴를 선택하거나 조정할 때 누릅
니다.
4. 메뉴 버튼 메뉴화면을 나타나게 하거나 기능을 선택할 때 누릅니다.
5. 전원 표시등 사용 중에는 켜지고 전원을 끄면 꺼집니다.
6. 전원 버튼 화면을 켜고 끌 때 누릅니다.
참고: 절전기능에 대한 자세한 내용은 제품규격의 절전기능 을 참조하세요. 모니터를 장시간 사용하지
않을 때에는 전력 소비를 줄이기 위해 완전히 꺼 두는 것이 좋습니다.
SyncMaster 765MB

Rear
(The configuration at the back of the monitor may vary from product to product.)
1. Power port Connect the power cord for your monitor to the power port on the back of
the monitor.
2. Signal Cable
Connect the signal cable to the video port on your computer, video board,
video card, or graphics card.
Note: See Connecting Your Monitor for further information regarding cable connections.

Bottom
1. Signal Cable Connect the signal cable to the video port on your computer, video
board, video card, or graphics card.
2. Power port
Connect the power cord for your monitor to the power port on the back of
the monitor.
3. Tilt/Swivel Base You can separate the base from the monitor.

Connecting Your Monitor
SyncMaster 763MB
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connect the signal cable to the video port on your computer, video board, video card, or
graphics card.
3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the
pins on your adapter(Adapter not included). A PC-compatible computer does not need an
adapter.
4. Turn on your computer and monitor. If your monitor displays an image, installation is
complete.

Connecting Your Monitor
SyncMaster 765MB
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connecting the signal cables.
1) Connecting to the PC.
(Connect the signal cable to the video port on your computer, video board, video card, or
graphics card.)
2) Connecting the USB cable
Connect the USB cable to the USB port on the back of your monitor/computer.
3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the
pins on your adapter(Adapter not included). A PC-compatible computer does not need an
adapter.
4. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Windows ME
1. Insert CD into the CD-ROM driver.
2. Click "Windows ME Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed.
Windows XP/2000
1. Insert CD into the CD-ROM driver.
2. Click "Windows XP/2000 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
zInternet web site : http://www.samsung-monitor.com/ (WorldWide)
http://www.samsungusa.com/monitor/ (USA)
http://www.sec.co.kr/monitor/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Installing the Monitor Driver

Installing the Monitor Driver
4. Click the "Install" button in the "Warning" window.
5. If you can see following"Message" window, then click the"Continue Anyway" button.
Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/.
6. Monitor driver installation is completed.

Installing the Monitor Driver
Windows XP | Windows 2000 | Windows Me | Windows 98 | Windows 95 | Windows NT | Linux
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
?
Internet web site :
http://www.samsung-monitor.com/(Europe, Asia, South America)
http://www.samsungusa.com/monitor/ (USA)
http://www.sec.co.kr/monitor/ (Korea)
http://www.samsungmonitor.com.cn/(China)
Microsoft®Windows®XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

Installing the Monitor Driver
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the
model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then
click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage

Installing the Monitor Driver
http://www.samsung-monitor.com/
.
9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft®Windows®2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "Start" , "Setting" , "Control Panel".
2. Double click the "Display" Icon.
3. Choose the "Settings" tab and then click "Advanced..".
4. Choose "Monitor".
5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a specific
driver" then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button. And
click the "Finish" button then the "Close" button.
Case1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
http://www.samsung-monitor.com/
.