Samsung SCC-B5343 User manual

SCC-B5342
SCC-B5343
operating instructions
Digital Color Dome Camera
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/global/register
ENG FRA GER SPA ITA TUR
01-B5342_B5343-00648D(03)Eng.ind1 1 2008-08-22 오후 4:48:57

2
3
This symbol indicates high voltage
is present inside. It is dangerous to
make any kind of contact with any
inside part of this product.
This symbol alerts you that important
literature concerning operation and
maintenance has been included with
this product.
To prevent damage which may result in re
or electric shock hazard, do not expose this
appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter
that is specied in the specication
sheet. Using any other adapter could
cause re, electrical shock, or damage
to the product
2. Incorrectly connecting the power
supply or replacing battery may cause
explosion, re, electric shock, or damage
to the product.
3. Do not connect multiple cameras to a single
adapter. Exceeding the capacity may cause
abnormal heat generation or re.
4. Securely plug the power cord into the
power receptacle. Insecure connection
may cause re.
5. When installing the camera, fasten it
securely and rmly. A falling camera may
cause personal injury.
6. Do not place conductive objects (e.g.
screwdrivers, coins, metal things, etc.) or
containers lled with water on top of the
camera. Doing so may cause personal
injury due to re, electric shock, or falling
objects.
7. Do not install the unit in humid, dusty, or
sooty locations. Doing so may cause re
or electric shock.
8. If any unusual smells or smoke come
from the unit, stop using the product. In
such case, immediately disconnect the
power source and contact the service
center. Continued use in such a condition
may cause re or electric shock.
Safety Precautions
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE REAR
COVER. NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
01-B5342_B5343-00648D(03)Eng.ind2 2 2008-08-22 오후 4:48:58

2
ENG
3
9. If this product fails to operate normally,
contact the nearest service center. Never
disassemble or modify this product
in any way. (SAMSUNG is not liable
for problems caused by unauthorized
modications or attempted repair.)
10. When cleaning, do not spray water
directly onto parts of the product. Doing
so may cause re or electric shock.
CAUTION
1. Do not drop objects on the product or
apply strong shock to it. Keep away from
a location subject to excessive vibration
or magnetic interference.
2. Do not install in a location subject to
high temperature (over 122°F), low
temperature (below 14°F), or high
humidity. Doing so may cause re or
electric shock.
3. If you want to relocate the already
installed product, be sure to turn off the
power and then move or reinstall it.
4. Remove the power plug from the
outlet when then there is a lightning.
Neglecting to do so may cause re or
damage to the product.
5. Keep out of direct sunlight and heat
radiation sources. It may cause re.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards
extremely bright objects such as sun,
as this may damage the CCD image
sensor.
8. Apparatus shall not be exposed to
dripping or splashing and no objects
lled with liquids, such as vases, shall be
placed on the apparatus.
9. The Mains plug is used as a disconnect
device and shall stay readily operable at
any time
FCC Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept any interference
received including interference that may
cause undesired operation.
Note
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment
in a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
01-B5342_B5343-00648D(03)Eng.ind3 3 2008-08-22 오후 4:48:58

4
5
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, or
other apparatus (including ampliers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong is provided for your safety.
If the provided plug does not t into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories
specied by the manufacturer.
12. Use only with cart, stand, tripod, bracket,
or table specied by the manufacturer, or
sold with the apparatus.
13. Unplug this apparatus. When a cart is
used, use caution when moving the
cart/apparatus combination to avoid
injury from tip-over.
14. Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or been dropped.
01-B5342_B5343-00648D(03)Eng.ind4 4 2008-08-22 오후 4:48:58

4
ENG
5
Overview ......................................................................................6
About this guide ............................................................................6
Product overview...........................................................................6
Main features .................................................................................6
Components...................................................................................6
Checking components in the package .......................................6
Components of your camera......................................................7
Installation ..................................................................................8
Setting switches ............................................................................8
Setting function switches............................................................8
Connecting cables and changing the settings.........................10
Installing camera ......................................................................... 11
Before installation..................................................................... 11
Installation procedure............................................................... 11
Adjusting the camera direction..................................................12
Appendix A: Specications for NTSC Standard........... 14
Appendix B: Specications for PAL Standard .............. 15
Contents
01-B5342_B5343-00648D(03)Eng.ind5 5 2008-08-22 오후 4:48:58

6
7
Overview
❚About this guide
This user guide includes basic instructions for
the product. It is recommended that all users
read this guide before use.
This guide is divided as follows:

Chapter 1, “Overview,” introduces the user guide
and product related information. (This chapter)

Chapter 2, “Installation,” explains how to set and
install the product.

Appendix, “Specications,” provides the
specications of the product.
❚Product overview
This is the high resolution (540 TV lines) dome
camera equipped with a Vari-focal lens, which
has no dynamic delay when implementing
motion pictures, and provides the features
such as digital noise reduction (DNR) by real-
time CCD defect compensation, low speed
shutter (LSS: Auto x128) to implement clear
picture quality, Day/Night color compensation,
and the like.
❚Main features

Power: DC 12V/AC 24V

Special functions

Line lock (LL) control

Auto white balancing

Horizontal/vertical image reversing

Flickerless control

Low shutter speed control

Backlight compensation control

Automatic switching between color and black
& white modes

Equipped with vari-focal lens

Auto Iris function

Digital noise reduction (DNR)

Dynamic CCD defect compensation
❚Components
Checking components in the package
Please check your camera and accessories
are included in the package. Those
components are as shown below:
Camera Test Monitor Cable
Tab screw User’s Guide
Note
The test monitor cable is used to test the camera
by connecting to a portable display. If you really
want to connect the camera to a monitoring
display, use the BNC cable.
01-B5342_B5343-00648D(03)Eng.ind6 6 2008-08-22 오후 4:48:58

6
ENG
7
Components of your camera
Your camera has the following components:
1Cover dome: Covers the main body for protection.
2Main body: Includes a lens, a switch board, a PCB
board, screws, and such.
3Mount bracket: Used as a ceiling or wall xture. It
is xed using three long tab screws provided in the
package.
4Cable Stopper: If drawing the cable from a hole in
the ceiling, remove this stopper and pass the cable
through the opening to connect.
5Zoom lever: Using this lever, the lens zoom can be
adjusted and xed.
6Focus lever: The lens focus can be adjusted by
rotating it left or right. Rotate it clockwise for xing.
7 Tiltxingscrew: Using this screw, the slope of the
lens can be adjusted and xed.
8Switch board: Includes two kinds of control switches
such as function switches and phase-control switches.
The board has eight function switches in the middle
and two phase-control buttons on each side of the
function switch area.
9Installation Guide Mark: This mark must be aligned
with the marking on the bracket when attaching the
camera to the bracket.
0Lock releaser: Push it outward and rotate the main
body in UNLOCK direction when you want to remove
the Mount bracket from the Main body or to remove
the installed camera from the Mount bracket.
!Cable: Connect the Video connector to BNC cable
and Power connector to power adapter.
1
2
!
Power connector
Video connector
Lens
7 8
9
56
0
4
3
01-B5342_B5343-00648D(03)Eng.ind7 7 2008-08-22 오후 4:49:00

8
9
❚Setting switches
Setting function switches
To set the available functions on your camera, adjust eight switches as shown below:
Installation
No Name Brief description
1 LL Line lock ON/OFF
2 LSS Sens-up or Low speed shutter ON/OFF
3H-REV Horizontal reverse ON/OFF
4V-REV Vertical reverse ON/OFF
5 BLC Backlight compensation ON/OFF
6FL Flickerless ON/OFF
7D/N Automatic switching between color and
black & white ON/OFF
8AWB Automatic white balance ON/OFF
1. Switch 1 (LL): When this switch is set to OFF, the camera operates in the internal
synchronization mode, while when it is set to ON, the camera operates in the line lock mode.
In the internal synchronization mode, the camera always uses an inside crystal oscillator for
synchronization. However if multiple cameras are connected to a sequential switcher, picture
rolling or ickering may occur when switching from one camera to another. In this case, you
can set this switch to ON to solve this problem.
The line lock mode allows the camera to use the phase of the AC power as the
synchronization reference. In this mode, you can use the phase control buttons(INC/DEC).
Note
When you are using the DC 12V power, set this switch to OFF. The line lock feature will not normally
operate even when the switch is set to ON.
Set the LL switch to ON while the AC power is connected. If any picture roll happens, you have
to adjust the phase using the phase-control buttons. Press the INC or DEC button to increase or
decrease the phase by one degree.
DEC
INC
8
7
6
5
4
3
2
1
01-B5342_B5343-00648D(03)Eng.ind8 8 2008-08-22 오후 4:49:01

8
ENG
9
2. Switch 2 (LSS): This sens-up mode accumulates the image elds in memory to reduce
noise but increase the brightness and contrast rate. When this switch is set to ON, the
camera automatically switches to a maximum of 128 times of image acquisition speed to
implement a clear picture for darker image.
3. Switch 3 (H-REV): When this switch is set to ON, the camera image is reversed horizontally.
If you want to monitor your site using a mirror, you can use this feature to see the right
image.
4. Switch 4 (V-REV): When this switch is set to ON, the camera image is reversed vertically.
If your camera reluctantly displays the vertically reversed image, you can use this feature to
see the right image.
5. Switch 5 (BLC): When this switch is set to ON, you can view a clear image even though the
camera faces any excessive light such as sunlight and uorescent light. When it is set to
OFF, the subject with excessive light is not clearly shown.
6. Switch 6 (FL): When this switch is set to ON, the shutter speed is xed to 1/100 sec (for
NTSC) or 1/120 sec (for PAL) to prevent screen from ickering by the disaccordance
between vertical synchronous frequency (50Hz for NTSC, 60Hz for PAL) and on-and-off
frequency of a light.
7. Switch 7 (D/N): When this switch is set to ON, the camera automatically switches between
color and B&W according to the brightness of the vicinity.
8. Switch 8 (AWB): This switch adjusts white balancing. When this switch is set to ON, this
camera operates in ATW mode, and in case of OFF, this camera operates in AWC mode.

ATW (Auto Tracking White Balance): The color temperature is automatically adjusted according to the
environmental change. (Approx. 2000°K to 11,000°K)

AWC (Auto White Balance Control): It stores the color temperature just when the switch is changed to
OFF. Accordingly color temperatures are adjusted by the stored value.
Caution
-. The IRIS setting range for the camera is approximately 80 to 120 IRE. It means the camera does not
provide the IRIS full open/close feature but the restricted variation range.
-. Use the camera after setting to the proper level (80 IRE or above) because the IRIS hunting may
occur when the level is 75 IRE or below.
01-B5342_B5343-00648D(03)Eng.ind9 9 2008-08-22 오후 4:49:01

10
11
❚Connecting cables and changing the settings
Before installing your camera, you have to adjust the lens focus, zoom, and switch settings.
To connect cables
1. Connect the BNC cable
to the Video connector
attached on your camera.
2. Connect the BNC cable
to the Video Input on a
monitor.
3. Connect the power adapter
to the Power connector
attached on your camera.
When the monitor is turned
on, the camera image
appears.
To adjust the lens focus, zoom, and function settings
1. Remove the Cover dome and Inner cover. For more details about the removing procedures,
see “Installation procedure,” in the Installing camera section on the next page.
2. Adjust the focus, zoom, and function settings of your camera using the Focus lever, Zoom
lever, and Switch board while you are viewing the image on the screen.
3. If you want to x the adjusted focus and zoom, screw up the levers.
BNC Cable
Monitor
01-B5342_B5343-00648D(03)Eng.ind10 10 2008-08-22 오후 4:49:02

10
ENG
11
❚Installing camera
Before installation
Before installing your camera, you have to read the following cautions:

You have to check whether the location (ceiling or wall) can bear ve times the weight of your camera.

Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it
may cause a breakdown or re.

When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.

Partial blind spot can occur at tilt angles of less than 20°, depending on the lens conguration.
Installation procedure
To install your camera
1Pry up the outer casing with a at-head screwdriver
to remove the protective cover from the Main body of
the camera.
2Remove the Mount bracket from the Main body by
rotating the Main body in the UNLOCK direction while
pushing the Lock releaser outward. If it is not easily
done, rotate the Mount bracket in the LOCK direction
while holding small holes on the Mount bracket.
3Fix the Mount bracket to the location (ceiling or wall)
with supplied three screws.
Note
The CAMERA FRONT sign on the Mount bracket
should face the camera monitoring area.
1
3
2
Ceiling mount
opener
01-B5342_B5343-00648D(03)Eng.ind11 11 2008-08-26 오후 6:31:27

12
13
4If a hole has been drilled on the bracket installation surface for cable access, press down to remove
the Cable Stopper and then draw the cable in. If connecting through the side of the camera, use the
empty space opposite to the side marked CAMERA FRONT.
5Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning
the Groove mark on the Main body with the wide groove around the CAMERA FRONT inlay.
6Adjust the camera direction. For more details on the direction control, see “Adjusting the camera
direction,” on the same page. When required to adjust the zoom and focus for your camera, see
“Connecting cables and changing the settings,” on page 10.
7Attach the Inner cover to the Main body by pressing it until a “click” sound is heard after aligning
two screw holes on the Wing lockers of the Inner cover with two screw holes on the Main body’s
left and right sides.
8Finally attach the Cover dome to the Main body by pressing it until a “click” sound is heard after
aligning the bump inside the Cover dome with the Groove mark on the Main body.
❚Adjusting the camera direction
When the camera is xed on the ceiling, you can adjust
the camera viewing angle. You can rotate your camera
leftward or rightward (Panning), and can change the slope
of your camera upward or downward (Tilting).
In case of panning, the rotation limit of your camera is
set to 355 degree (100 degree clockwise and 255 degree
counterclockwise). The rotation is stopped by the Stopper
inside of the camera. For panning control, rst unfasten
two screws located on the bottom and rotate in the
direction you want, and then fasten them to x the camera.
Tilt can be adjusted between 0° to 90°; however, tilt
angles of less than 20° may result in a partial blind spot,
depending on your lens conguration. To x the location
after adjusting the tilting angle, use the Tiltxingscrews.
To adjust the focus and zoom of your camera, use the Zoom lever and Focus lever. When
you install the camera on the inclined ceiling or wall, you can rotate the camera lens to see
a correct direction image.
Panning
Tilting
Lens rotation
01-B5342_B5343-00648D(03)Eng.ind12 12 2008-08-22 오후 4:49:03

12
ENG
13
SCC-B5342/B5343
01-B5342_B5343-00648D(03)Eng.ind13 13 2008-08-22 오후 4:49:03

14
15
Appendix A: Specications for NTSC Standard
Item Details
Product type CCTV color dome camera
Power input AC 24V ± 10% (60Hz ± 0.3 Hz), DC 12V +10%/-5%
Broadcast type NTSC Standard System (525 Lines, 60 Fields)
Power consumption Approx. 1.7W
Image device 1/3 inch IT Type Super-HAD CCD
Pixels Total: 811(H) x 508(V), 410,000 pixels
Effective: 768(H) x 494(V), 380,000 pixels
Scanning mode 525 Lines, 2:1 Interlace
Scanning line frequency Horizontal: 15.734Hz(INT)/15.750Hz(LL)
Vertical: 59.94Hz(INT)/60Hz(LL)
Synchronization mode INT/Line Lock (Adjusting the phase using INC/DEC button)
Horizontal resolution 540 TV Lines
S/N Ratio Approx. 50dB
Min. object illumination
SCC-B5343 (Color/BW) SCC-B5342 (Color/BW)
F1.2
Sens-up Off
50IRE 0.4/0.04Lux 0.4/0.4Lux
30IRE 0.24/0.024Lux 0.24/0.24Lux
15IRE 0.12/0.012Lux 0.12/0.12Lux
Sens-up x128
50IRE 0.0031/0.00031Lux 0.0031/0.0031Lux
30IRE 0.0019/0.00019Lux 0.0019/0.0019Lux
15IRE 0.0009/0.00009Lux 0.0009/0.0009Lux
Signal output COMPOSITE Video(1 . 0 Vp-p, 75ohm, BNC), Test Monitor OUT(1 . 0 Vp-p, 75ohm, Harness cable)
Lens Auto Iris (DC) / Focal length: 2.5 to 6.0mm / Aperture ratio: 1.2
PAN function Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
TILT function Range: 0 to 90°
Controls
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
Product color SCC-B5342N/B5343N : White
Operation temperature -10°C to +50°C
Operation humidity Up to 90%
Size 128(Ø) x 91(H)mm
Weight 327g
01-B5342_B5343-00648D(03)Eng.ind14 14 2008-08-26 오후 6:31:27

14
ENG
15
Appendix B: Specications for PAL Standard
Item Details
Product type CCTV color dome camera
Power input AC 24V ± 10% (50Hz ± 0.3 Hz), DC 12V +10%/-5%
Broadcast type PAL Standard System (625 Lines, 50 Fields)
Power consumption Approx. 1.7W
Image device 1/3 inch IT Type Super-HAD CCD
Pixels Total: 795(H) x 596(V), 470,000 pixels
Effective: 752(H) x 582(V), 440,000 pixels
Scanning mode 625 Lines, 2:1 Interlace
Scanning line frequency Horizontal: 15.625Hz(INT)/15.625Hz(LL)
Vertical: 50Hz(INT)/50Hz(LL)
Synchronization mode INT/Line Lock (Adjusting the phase using INC/DEC button)
Horizontal resolution 540 TV Lines
S/N Ratio Approx. 50dB
Min. object illumination
SCC-B5343 (Color/BW) SCC-B5342 (Color/BW)
F1.2
Sens-up Off
50IRE 0.4/0.04Lux 0.4/0.4Lux
30IRE 0.24/0.024Lux 0.24/0.24Lux
15IRE 0.12/0.012Lux 0.12/0.12Lux
Sens-up x128
50IRE 0.0031/0.00031Lux 0.0031/0.0031Lux
30IRE 0.0019/0.00019Lux 0.0019/0.0019Lux
15IRE 0.0009/0.00009Lux 0.0009/0.0009Lux
Signal output COMPOSITE Video(1 . 0 Vp-p, 75ohm, BNC), Test Monitor OUT(1 . 0 Vp-p, 75ohm, Harness cable)
Lens Auto Iris (DC) / Focal length: 2.5 to 6.0mm / Aperture ratio: 1.2
PAN function Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
TILT function Range: 0 to 90°
Controls
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
Product color SCC-B5342P/B5343P : White
Operation temperature -10°C to +50°C
Operation humidity Up to 90%
Size 128(Ø) x 91(H)mm
Weight 327g
01-B5342_B5343-00648D(03)Eng.ind15 15 2008-08-26 오후 6:31:27

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems)
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government ofce, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
01-B5342_B5343-00648D(03)Eng.ind16 16 2008-08-22 오후 4:49:04

SCC-B5342
SCC-B5343
Mode d’emploi
Caméra Dôme Numérique Couleur
imaginez les possibilités
Merci d’avoir acheté un produit Samsung.
Pour bénécier d’un service plus complet,
veuillez vous enregistrer sur
www.samsung.com/global/register
FRA
02-B5342_B5343-00648D(03)Fre.ind1 1 2008-08-22 오후 6:18:43

2
3
Ce symbole indique la présence,
dans cette unité, d’une tension élevée
et avise des risques de décharge
électrique existants.
Ce symbole indique la présence,
dans cette unité, d’une tension élevée
et avise des risques de décharge
électrique existants.
ATTENTION
•
An de réduire le risque d’incendie ou de
décharge électrique, n’exposez pas cet
appareil à la pluie ni à l’humidité.
ATTENTION
1. Assurez-vous d’utiliser uniquement
l’adaptateur standard spécié dans la che
des caractéristiques techniques. Utiliser
tout autre adaptateur peut provoquer
des risques d’incendie ou des chocs
électriques et endommager le produit.
2. Un branchement incorrect de
l’alimentation électrique ou un mauvais
remplacement de la pile peut provoquer
des risques d’incendie, des chocs
électriques ou des dommages au produit.
3. Ne pas connecter plusieurs caméras à
un seul adaptateur. Dépasser la capacité
peut générer une chaleur anormale ou un
risque d’incendie.
4. Branchez correctement le cordon d’
alimentation dans la prise. Une mauvaise
connexion peut provoquer des risques d’
incendie.
5. Lors de l’installation de la caméra,
attachez-la fermement et en toute sécurité.
Une caméra qui tombe peut causer des
blessures.
6. Ne placez pas d’objets conducteurs
(tourne-vis, pièces de monnaie, objets en
métal, etc...par exemple) ou des récipients
remplis d’eau sur la caméra. Cela peut
causer des blessures dues au feu, au choc
électrique ou à la chute d’objets.
7. Ne pas installez l’appareil dans des lieux
humides, poussiéreux ou couverts de suie.
Cela peut provoquer des risques
d’incendie ou des chocs électriques.
8. Si vous constatez une odeur ou une fumée
inhabituelle provenant de l’appareil, arrêtez
immédiatement son utilisation. Dans de
tel cas, déconnectez immédiatement
la source d’alimentation et contactez le
centre de maintenance. Si vous continuez
à utiliser le produit dans de telle condition,
cela peut provoquer des risques d’incendie
ou des chocs électriques.
PRÉCAUTIONS DE SÉCURITÉ
ATTENTION : POUR REDUIRE LES RISQUES DE CHOCS ELECTRIQUES, NE PAS
OUVRIR LE COUVERCLE ARRIERE. LES PIECES INTERIEURES NE SONT PAS
ACCESSIBLES A L’UTILISATEUR. FAITES APPEL AU PERSONNEL DE MAINTENANCE
QUALIFIE.
ATTENTION
RISQUE DE ECHOC ELECTRIQUE NE PAS OUVRIR
02-B5342_B5343-00648D(03)Fre.ind2 2 2008-08-22 오후 6:18:43

2
3
FRA
9. Si ce produit ne fonctionne pas
normalement, contactez le centre de
maintenance le plus proche. Ne jamais
démonter ou modier le produit de quelque
manière que ce soit. (SAMSUNG n’est
pas responsable des problèmes causés
par des modications ou des tentatives de
réparation non autorisées.)
10. Lors du nettoyage, ne pas diriger l’eau
directement sur les pièces de l’appareil.
Cela peut provoquer des risques
d’incendie ou des chocs électriques.
MISE EN GARDE
1. Ne pas faire tomber des objets sur le
produit ou lui faire subir des chocs.
Eloignez le produit des emplacements
soumis aux vibrations ou interférences
magnétiques excessives.
2. Ne pas installer le produit à des
emplacements soumis aux températures
élevées (supérieures à 50 °C), aux
températures faibles (inférieures à -10°
C), ou à une humidité élevée. Cela peut
provoquer des risques d’incendie ou des
chocs électriques.
3. Si vous désirez changer le produit de
place, assurez-vous de le mettre hors
tension, déplacez-le et réinstallez-le.
4. Débranchez le cordon d’alimentation de
la prise lorsqu’il y a des éclairs. Ne pas
appliquer cette consigne peut provoquer des
risques d’incendie ou endommager le produit.
5. Eloignez le produit des rayons directs du
soleil ou des sources de radiation de chaleur.
Cela peut provoquer des risques d’incendie.
6. Installez le produit dans un lieu où la
ventilation est sufsante.
7. Evitez de pointer la caméra directement
vers des objets extrêmement brillants
comme le soleil, cela peut endommager le
capteur d’image CCD.
8. Veillez à éviter toute projection sur l’
appareil et ne placez jamais de récipients
contenant un liquide (ex. : vase) dessus.
9. La prise d’alimentation fait ofce de
système de déconnexion ; elle doit donc
rester disponible en permanence.
02-B5342_B5343-00648D(03)Fre.ind3 3 2008-08-22 오후 6:18:43

4
5
INSTRUCTIONS IMPORTANTES RELATIVES À LA SÉCURITÉ
1. Veuillez lire ces instructions.
2. Conservez ces instructions.
3. Prêtez attention à tous les avertissements.
4. Veuillez suivre toutes les instructions.
5. N’utilisez pas cet appareil à proximité de
l’eau.
6. Nettoyez-le avec un tissu sec.
7. N’obstruez pas les ouvertures de
ventilation. Procédez à l’installation
conformément aux instructions du
fabricant.
8. Ne pas installer l’appareil à proximité de
sources de chaleur comme les radiateurs,
les registres de chaleur et les autres
appareils (incluant les amplicateurs)
produisant de la chaleur.
9. Veillez à vous conformer aux sécurités
des prises de terre et polarisées. Une
prise dite polarisée est composée de deux
ches, une plus large que l’autre. Une
prise de terre est composée de deux ches
et d’une troisième che pour la terre. La
troisième che, plus large que les deux
autres, est fournie pour votre sécurité. Si
la prise qui vous est fournie ne correspond
pas à votre prise murale, demandez à un
électricien de remplacer la prise obsolète.
10. Veillez à ce que personne ne marche ou
se prenne les pieds dans le cordon
d’alimentation et particulièrement au
niveau des ches et des prises de courant
et au niveau où ils se situent.
11. N’utilisez que des accessoires ou des
produits additionnels spéciés par le
fabricant.
12. N’utilisez que des chariots, des pieds,
trépieds, ou tables spéciés par le fabricant
ou vendus avec l’appareil.
13. Débranchez cet appareil. Si vous utilisez
un chariot, faîtes attention lorsque que
vous déplacez l’appareil et le chariot
pour éviter les blessures causées par un
renversement.
14. Veuillez faire appel au personnel qualié
pour tous travaux de maintenance. Les
travaux de maintenance sont nécessaires
si l’appareil a été endommagé de quelque
manière que ce soit, comme cordon
d’alimentation endommagé, liquide
répandu, objets tombés sur l’appareil,
appareil exposé à la pluie et à l’humidité,
il ne fonctionne pas normalement ou est
tombé par terre.
02-B5342_B5343-00648D(03)Fre.ind4 4 2008-08-22 오후 6:18:43