Samsung SID-462 User manual

Outstanding 24-Hour
image 580TVL
High Resolution Day & Night Dome Camera SID-462 User ’ s Manual
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH

Before operating the camera, confirm the camera model and proper input power
voltage. In order to that you can understand this manual thoroughly, we'll introduce our
model description.
n SID-462 SERIES
 •NTSCMODEL •PALMODEL
 SID-462(W)N SID-462(W)P
nMODEL DESCRIPTION
 •SID-462(W)X
_ _
 •SIGNALSYSTEM
  NNTSCMODEL
  PPALMODEL
 •CAMERACOLOR
SILVERCOLOR
  WIVORYCOLOR
This installation should be made by a qualified service person and
should conform to all local codes.
Thelightningflashwithanarrowheadsymbol,withinanequilateraltriangleis
intended to alert the user to the presence of uninsulated “dangerous voltage”
withintheproduct'senclosurethatmaybeofsufficientmagnitudetoconstitute
a risk of electric shock to persons.
Theexclamationpointwithinanequilateraltriangleisintendedtoalerttheuser
tothepresenceofimportantoperatingandmaintenance(servicing)instructions
in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the
equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
SIGNALSYSTEM
CAMERACOLOR

COLOR DOME CAMERA User’s Manual
4
COLOR DOME CAMERA User’s Manual
5
Contents
Contents
• Precautions …………………………………………………………………… 7
• Components and Accessories …………………………………………… 8
• Overview ………………………………………………………………………… 9
• Installation …………………………………………………………………… 10
nInstallation
 
n Adjustthepanningandtilting,rotatingwhilewatchingthemonitor 
• Connection ……………………………………………………………………… 13
nConnectingToMonitor
  

nConnectingToPower
 

nRS-485communicationcontrol
 
• Operating Your Camera …………………………………………………… 15
nMenuConfiguration
 

nMenuSetup
  

•LENS
 

•EXPOSURE
  

•WHITEBALANCE
  

•BACKLIGHT
 

•SSNR
 

•DAY/NIGHT
  

•IMAGEADJ
  

•SPECIAL
  

•EXIT
  
• Troubleshooting ……………………………………………………………… 28
• Dimension ……………………………………………………………………… 29
• Specification   30
Features
Excellent Sensitivity
Thebuilt-inhigh sensitivityCOLORCCDenable
aclearimage even in 0.15Lux(COLOR),0.0006
Lux(Color,256xSens-up)orlowerillumination.
Day&Night
Thecameraidentifieswhetheritisdayornight
and automatically switches to the appropriate
mode, depending on its environment. By day,
the camera switches to color mode in order to
maintainoptimalcolor.Atnight,itswitchestoB/
Wmodesoastoobtainbetterpicturedefinition.
DIS (Digital Image Stabilizer)
TheDISfunctioncompensatesfor any camera
movement,toproducemorestablepictures.
3-Axis camera mechanism
TheSID-462isespeciallyincrediblyflexibleto
installwithits3-axiscameraconstruction,
which makes the camera wall or slope
mountable.
Miscellaneous Functions
HLC(HighLightCompensation),SENS-UP, FLIP
(H/V-REV),D-ZOOM,SHARPNESS,MOTION
DETECTIONandPRIVACYfunctionsare
provided.
RS-485 Communication
Control Support
RemoteOSDmenucontrolviaanRS-485
interface is supported.
OSD
Thecameracontrolis convenientby using8
differentforeignlanguageO.S.D.
-NTSC:Korean, English,French,Spanish,
Japanese
-PAL:English,French,German,Spanish,
Italian,Chinese
SSNR (Samsung Super Noise
Reduction) Function
ThehighperformanceW-IVDSPchip
dramatically reduces the gain noise in digital
image processing, producing clear, sharp
images in low lighting environments.
Ultra High Resolution
Byadoptingadiagonal6mm(1/3")410,000
(NTSC)pixel,470,000(PAL)pixelSONYCCD,the
cameraproducesclearpicturequalitywitha
horizontalresolutionof580TVlinesforcolor.

COLOR DOME CAMERA User’s Manual
6
COLOR DOME CAMERA User’s Manual
7
SamsungTechwincaresfortheenvironmentatallproductmanufacturing
stagestopreservetheenvironment,andistakinganumberofstepstoprovide
customerswithmore environment-friendly products.TheEcomarkrepresents
SamsungTechwin’swilltocreateenvironment-friendlyproducts,andindicates
thattheproductsatisfiestheEURoHSDirective.
Thisinformationisprovidedtoensureyoursafetyandtopreventanylosses,financialor
otherwise.Pleasereaditcarefullyandusetheproductaccordingly.
 *Forproductinquiries,pleasecontacttheretailshopwhereyouboughtthecamera.Theuseofequipmentsuchas
anaerialladderwhileprovidingafter-salesserviceshallbeatyourexpense.
 *Separatethepowerplugwhenthundercrashesorlightingflashes.
 *Thisproductissupportequipmentforsurveillancesystem.Therefore,wecan'tcompensateformateriallossand/or
personalinjuriesbyrobbery,fire,naturaldisasterorsomethinglikethistype.
Ignoring this information may
resultinmateriallossand/or
seriouspersonalinjuriesincluding
death.
Indicates“NeverAllowed.”
Ignoring this information may
resultinmateriallossand/ora
slightinjuries.
Indicates “NoDisassembling.”
Warnings & Cautions
Warning/Attention/Special Mark Messages
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Severe lighting changes or flickering may hinder
normal camera operation.
May lower image quality.Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
Avoid touching the camera lens.
Do not drop the camera or subject
it to physical shock.
May damage the CCD.May cause a product malfunction.
Never keep the camera face to
strong light directly.
Do not install under unstable
lighting conditions.
Precautions

COLOR DOME CAMERA User’s Manual
8
COLOR DOME CAMERA User’s Manual
9
Overview
Precautions
•Ifthecameraisexposedtospotlightorobjectreflectingstronglight,smearor
bloomingmayoccur.
•Pleasecheckthatthepowersatisfiesthenormalspecificationbeforeconnecting
the camera.
Notes
Do not expose the camera to
radioactivity.
❶
SID-462
2
InstructionManual
3
M4TappingScrew4EA
4
M4MachineScrew4EA
5
Adapterplate
6
InstallationVideoOutputCable
❶
5
6
2 3
If it is exposed to radioactivity, For heated CCD, it
will be out of order.
1 2 3
4
5
❿
8
76
⓬
⓫
9
Components and Accessories
4
❶Pan Base : control panning angle of camera
2Rotate Base : control rotating angle of camera
3X3.6 Vari-focal Lens Module
4Rotate Base Holding Screw : fix rotated position
5Pan Base Holding Screws (Color : Silver) : fix panned position
6RS-485 Control Cable : The detailed description refers to p14
7Power Input Connector
8Video Output Jack
9Function Setup switch : Display the menu on the screen and move the cursor to four
directions to confirm status or after changing a selected
item.
❿Video Output Terminal to Monitor
⓫Shield Case
⓬Dome Cover

COLOR DOME CAMERA User’s Manual
10
COLOR DOME CAMERA User’s Manual
11
1) Separate the dome cover by counterclockwise rotation.
2) Separate the shield case by pulling from the camera body.
•Theinstallationshouldbedonebyqualifiedservicepersonnelorsysteminstallers.
•Iftheceilingmaterialisnotstrongenoughtoholdtheinstallationscrews,thecamera
mayfalloff.Reinforcetheceilingasneeded.
Notes
* To install the dome cover on the camera
body, turn the latches in locking direction
as shown in the figure 1.
Lockingdirection
(Clockwise)
Latch
Lockingdirection
[Figure-1]
MainBody
(Camera)
ShieldCase
Domecover
Unlockingdirection
(Counterclockwise)
Installation
Installation
When installing on a adapter plate
1) Place the bracket provided on the installation
surface and fix it with the M4 tapping screws
(provided).
2) When placing the camera body on the plate,
insert the plate pin into the mounting hole on
the body as shown in figure-1 and fix it by
turning clockwise.
3) When placing the camera body on the plate,
make sure the power and the BNC cables pass
through their respective designated holes.
(When placing the cable through its side, thread
it through the hole at the bottom.)
4) After installation and adjustment of the camera
are complete, secure the dome cover by turning
it clockwise.
[Figure-1]
Lockingdirection
Platepin
Unlockingdirection
•Pleaselocateanarrowonbracketforinstallingdirectionthatyouwishtoobserve
AreaandthenfixitwiththeM4tappingscrews.
Notes
Unlocking
direction
M4tapping
screw(provided)
Domecover
adapter plate
Anarrowforinstallingdirections
CAMERA
Locking
direction
Installation

COLOR DOME CAMERA User’s Manual
12
COLOR DOME CAMERA User’s Manual
13
1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.
 •PanBasemovesby170˚toeachsidedirectionand340˚onthewhole.
 •TiltBasecoverstotal146˚angle(73˚toeachside).
 •AnglerangeofRotateBaseisthesameasthatofPanBase.ButOnesiderangeis195˚
andanotheris145˚
2) Methods of adjustment
 •The case of wall installation
1 Aftermountingthecameraonawall,adjustingthepanninganglesothatthecameracan
face the direction to monitor when tilting.
2 Andthenadjustthetiltinganglebyrotatingthetiltbase.
3 Loosentherotatebaseholdscrewandadjustrotatebaseforthebestmonitoring.
4 Tighten the rotate base hold screw.
 •The case of ceiling installation
1 Aftermountingthecameraonaceiling,adjustingthepanningangleforbettermonitoring
area by rotating the pan base.
2 Andthenadjustthetiltinganglebyrotatingthetiltbase.
3 Loosentherotatebaseholdscrewandadjustrotatebaseforthebestmonitoring.
4 Tighten the rotate base hold screw.
73˚
-170˚
145˚ 195˚
170˚
PanBase
TiltBase
RotateBase
Adjust the panning and tilting, rotating while watching the monitor
Installation
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
CCTVCamera Monitor
• As the connecting method varies with the instruments, refer to the manual supplied with the
instrument.
• If necessary, you can connect the monitor to the REMOTE jack on the back of your camera.
• Only connect the cable when the power is turned off.
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
CCTVCamera
Intermediate End monitor
Connect the adaptor to the power input connector as shown in the figure below. The
recommended adaptor specification for SID-462N/SID-462P is AC 24V / 300mA or DC 12V /
500mA.
Connection
Connecting Monitor
Connecting to Power

COLOR DOME CAMERA User’s Manual
14
COLOR DOME CAMERA User’s Manual
15
Operating Your Camera
• As shown in the table above, voltage decreases as the wire gets longer. Therefore
use of an excessively long adaptor output line for connection to the camera may
affect the performance of the camera.
*Standard voltage for camera operation : AC 24V ± 10%, DC 12V ± 10%
* There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
•Besuretoconnectpoweronlyafteralltheinstallationiscomplete.
•NotethatAC/DCadaptorisnotsuppliedwithcamera.
•GroundshouldbeconnectedtotheGNDterminal.
Notes
When the resistance value of copper wire is at [20˚C(68˚F)]
Connecting to RS-485 Control Cable
Using a RS-485 communication, it will be able to control the OSD menu at the
SAMSUNG TECHWIN System Controller or DVR.
(1) The case which it controls from the PC
Using a RS-485 converter, It connects to RS-485 control cable outside camera and
serial cable
 EX)SERIALPORTOFTHEPC(COM1) → SERIALCABLE → RS-485CONVERTER → RS-485CONTROL
CABLE
(2)The case which it controls from the DVR or System Controller
It connects the RS-485 control cable in the connection terminal of 485 control boards
which are connected with the DVR or System Controller.
•Whenyouconstructexternalcontrolsystemsforacameracontrol,pleaseusetothe
SAMSUNGTECHWINPROTOCOLorPELCO-DPROTOCOL.
•WhenyouconnectingtoRS-485controlcable,pleasepeelofftheouterskininsidethe
RS-485controlcable.
• IncaseofSCC-101connection,changecommunicationmodeto8-E-1at Communication
configurationmenu.(Formoreinformation,refertoSCC-101manual.)
Notes
* RS-485 Communication establishment initial value
Menu Configuration
Copper wire size (AWG) #24(0.22mm2)#22(0.33mm2)#20(0.52mm2)#18(0.83mm2)
Resistance (Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
Item Camera ID BAUD RATE UART MODE PET PKT
Initial value 19600 8-NONE-1 ENABLE
Setup Menu
LENS
 DC
EXPOSURE
 SHUTTER  AGC  SENS-UP
 RETURN
WHITE BALANCE
 ATW  MANUAL  AWC → SET
 OUTDOOR  INDOOR
BACKLIGHT
 OFF  BLC  HLC
SSNR
 ON  OFF
DAY/NIGHT
 COLOR  B/W  AUTO
IMAGE ADJUSTMENT
(IMAGE ADJ.)
 V-REV  H-REV  D-ZOOM
 SHARPNESS  RETURN
SPECIAL
 CAMTITLE  SYNC  MOTION DET
 PRIVACY  DIS  COMM ADJ
 LANGUAGE  RESET  RETURN
EXIT
Connection
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTION TERMINAL RED (TRX+)
(- ) CONNECTION TERMINAL WHITE (TRX-)
CONTROL CABLE SPEC
RED (TRX+) RS-485+
WHITE(TRX-) RS-485-
RS-485 communication control

COLOR DOME CAMERA User’s Manual
16
COLOR DOME CAMERA User’s Manual
17
FunctionSetupswitch
Use the Function Setup switch on the main body of the camera.
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
Menu Setup
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
Selectthefunctionby
moving up or down direction
of function setup switch.
Changethestatusby
moving right or left direction
of function setup switch.
DC : Select Auto Iris Lens
• When DC is selected, you can control screen brightness. The range of brightness
control is between 1 and 70. Adjust the brightness appropriately for optimal screen
brightness.
1. When the SETUP menu screen is displayed, select
’EXPOSURE‘ by using the Function Setup switch so that
the arrow indicates ’EXPOSURE‘.
2. Select a desired mode using the Function Setup switch.
•Anitemwiththe iconalsohassubmenus.Toselectasubmenu,selectanitemwiththeicon
andpresstheFunctionSetupSwitch.
•Anitemwiththe---iconisunavailableduetofunctionsettings.
Notes
Operating Your Camera
EXPOSURE
Using this function, you can control screen brightness.
1. When the SETUP menu screen is displayed, select ’LENS‘ by using the Function Setup
switch so that the arrow indicates ’LENS‘ .
SHUTTER : Because of using built-in dc lens, shutter
speed is fixed at 1/60(PAL:1/50)basically.
- A.FLK : Select this when you experience picture flicker, which can happen when
there is a clash with the frequency of the installed lighting.
LENS
MAIN SETUP
1.LENS DC
2.EXPOSURE
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW

COLOR DOME CAMERA User’s Manual
18
COLOR DOME CAMERA User’s Manual
19
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
AGC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen - but the higher the noise.
  -OFF:DeactivatestheAGCfunction.
  -LOW:Allowsautomaticgaincontrolfrom5.3dBto32dB.
  -HIGH:Allowsautomaticgaincontrolfrom5.3dBto37dB.
SENS-UP :
When it is night or dark, the camera automatically detects the light level and
maintains a clear picture if this mode is activated.
  -OFF:DeactivatestheSENS-UPfunction.
  -AUTO:ActivatestheSENS-UPfunction.
RETURN :
Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
•IfyoupresstheFunctionSetupSwitchin‘AUTO’mode,Youcanadjustbrightnessby
increasingordecreasingtheshutterspeed.(X2~X256)
•Notethatthehigherthezoomlevel,thebrighterthescreen,butthemorelikelyitis
thatanafter-imagewillappear.
•AlthoughNoise, Spots, andWhitishsymptomsmayoccurinSENS-UPoperation
when the zoom level is increased, this is normal.
Notes
Operating Your Camera
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ’White Bal.‘ by using the Function
Setup switch so that the arrow indicates ’White Bal.‘ .
2. Select a desired mode using the Function Setup switch.
 Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,800ºK and 10,500ºK.
INDOOR :
Select this when the color temperature is between 4,500ºK and 8,500ºK.
OUTDOOR :
Select this when the color temperature is between 1,800ºK and 10,500ºK.
(sodium light inclusion)
AWCSET :
To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the Function Setup switch. If the environment changes, readjust it.
•WhiteBalancemaynotworkproperlyunderthefollowingconditions.Inthiscase
selecttheAWCmode.
1
Whenthecolortemperatureofenvironmentsurroundingthesubjectisoutofthe
controlrange(e.g.clearsky,orsunset)
2
Whentheambientilluminationofthesubjectisdim.
3
If the camera is directed towards a fluorescent light or is installed in a place
whereilluminationchangesdramatically,theWhiteBalanceoperationmay
becomeunstable.
Notes
MANUAL :
Select this to fine-tune White Balance
manually. Set White Balance first by using the
ATW or AWC mode.After that switch to
MANUAL mode, fine-tune the White Balance
and then press the Function Setup switch.
White Balance (White Bal.)
This camera is designed so that it delivers a distinctive subject and background at the
same time, even when the subject is in backlight, unlike conventional cameras, by
adopting a proprietary W-IV DSP chip.
BACKLIGHT
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates ‘BACKLIGHT‘.

COLOR DOME CAMERA User’s Manual
20
COLOR DOME CAMERA User’s Manual
21
Operating Your Camera
BLC OFF
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
2. Select a desired mode using the Function Setup switch depending on the camera
purpose.
BLC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the switch.
•BecausetherecanbeadifferenceintheeffectivenessofHLCaccordingtotheamountof
lightareainthescreen,optimizetheinstallationangleforthebestHLCperformance.
•In a dark environment,theHLCisonlyactivated when a highlightthatislargerthana
certain area is present.
•TheHLCisnotactivatedinlightoroverlydarkconditions.
Notes
Select ‘BLC‘ to adjust the area to be
enhanced and enhancement level.
HLC :
Enable a user to select a mask color
of high light area from a picture.
HLC (High Light Compensation) :
If there is a high light installed in a limited environment such as an apartment
parking garage or gas station entrance, removing the high light makes it possible to
view car license plates efficiently.
- DAY : In normal daylight conditions, the HLC is not activated.
- NIGHT : If a high light that is larger than a certain size is present on the screen,
remove the high light to see license plates clearly.
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select ’SSNR‘ by using the Function
Setup Switch so that the arrow indicates ’SSNR‘ .
SSNR
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
2. Select a desired mode using the Function Setup switch.
OFF : Deactivates SSNR so that noise is not reduced.
ON : Activates SSNR so that noise is reduced.
3. Set the SSNR mode to ’ON‘ and press the Function
Setup switch. Then you can adjust the noise reduction
level.

COLOR DOME CAMERA User’s Manual
22
COLOR DOME CAMERA User’s Manual
23
2. Select a desired mode using the Function Setup switch according to the picture display
you want.
AUTO :The mode is switched to ‘Color’ in a normal environ
ment, but it is switched to ‘B/W’ mode when
ambient illumination is low. To set up the switching
time for AUTO mode, press the Function Setup
switch.
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
Please press the Function Setup switch to turn on or
off the burst signal on B/W mode.
- DWELL TIME :You can select the duration time about
changing the DAY/NIGHT mode.
5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
•YoucannotsettheSSNRto‘ON’or‘OFF’whentheAGCmodeoftheEXPOSURE
menuis‘OFF’.
•WhenadjustingthenoisereductionleveloftheSSNRmode,rememberthatthe
higherthelevelset,themorethenoiselevelwillbereducedbutthatafterimage
may also occur.
Notes
DAY/NIGHT
Operating Your Camera
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the
Function Setup switch so that the arrow indicates ‘DAY/NIGHT’.
•YoucannotcontroltheDAY/NIGHTmenuwhenAGCintheEXPOSUREmenuis‘OFF’.
Atthistime,theexchangebetweenDAYmodeandNIGHTmodeoperatesaslike
selecting ‘COLOR’mode.
•Thecameramayfocuslesswellunderinfraredilluminationthanundernormalillumination.
Notes
2. Select a desired mode using the Function
Setup switch.
1. When the SETUP menu screen is displayed,
select ‘IMAGE ADJ.’ by using the Function
Setup switch so that the arrow indicates
‘IMAGE ADJ.’
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
IMAGE SETUP
1. V-REV OFF
2. H-REV OFF
3. D-ZOOM OFF
4. SHARPNESS ON
5. RETURN
IMAGE ADJ.
V-REV : You can flip the picture vertically on the screen.
H-REV : You can flip the picture horizontally on the screen.
D-ZOOM : You can use a digital zoom of x2~x10.
SHARPNESS : As you increase this value, the picture
outline becomes stronger and clearer. Adjust
this value appropriately depending on the
sharpness of the picture.

COLOR DOME CAMERA User’s Manual
24
COLOR DOME CAMERA User’s Manual
25
RETURN : Select this to save the settings for the IMAGE
ADJ. menu and to return to the SETUP menu.
•WhentheV-REVorH-REVmodeisenabled,thetextonthescreendoesnotflip.
•IfyouincreasetheSHARPNESSleveltoohigh,the picture may become distorted or
noise may appear.
Notes
Operating Your Camera
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
5. DIS OFF
6. COMM ADJ
7. LANGUAGE ENGLISH
8. RESET
9. RETURN
1. When the SETUP menu screen is
displayed, select ’SPECIAL‘ by using the
Function Setup switch so that the
arrow indicates ’SPECIAL‘.
2. Select a desired mode using the
Function Setup switch.
SPECIAL
CAM TITLE : If you enter a title, the title will appear on the monitor.

If the SPECIAL menu screen is displayed, use the Function Setup switch so that
the arrow indicates ’CAM TITLE‘.

Set it to ’ON‘ by using the Function Setup switch.
❸ Press the Function Setup switch.
❹ Use the Function Setup switch to move
to a desired letter and select the letter
by pressing the switch. Repeat this to
enter multiple letters. You can enter up
to 15 letters.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
CLR POS END
•WhentheCAMTITLEmenuis‘OFF’,notitle
willbedisplayedonthemonitorscreen
even if you enter one.
•OnlyEnglishisavailableinthismode.
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
Notes

Enter a title, move the cursor to ‘POS’ and press the
Function Setup switch. The entered title appears on
the screen. Select the position to display the title on
the screen by using the Function Setup switch and
press. When the position is determined, select ‘END’
and press the Function Setup switch to return to the
SPECIAL menu.
•IfyoumovethecursortoCLRandpresstheFunctionSetupswitch,alltheletters
aredeleted.Toeditaletter,changethecursortothebottomleftarrowandpress
theFunctionSetupswitch.Movethecursoroverthelettertobeedited,movethe
cursortothelettertobeinsertedandthenpresstheFunctionSetupswitch.
Notes
FRONT DOOR
SYNC :
In areas where the supply is at 60Hz, you can
synchronize the output phase of multiple cameras
using the power synchronization function (Line-
Lock) without using a synchronization signal
generator.
  -INT:InternalSynchronizationType
  -L/L:PowerSynchronizationType,Line-lock

COLOR DOME CAMERA User’s Manual
26
COLOR DOME CAMERA User’s Manual
27
PRIVACY : Hide an area you want to hide on the screen.
  
When the SPECIAL menu screen is displayed, press
the Function Setup switch so that the arrow
indicates ‘PRIVACY’.
  
Set up the mode using the Function Setup switch.
MOTION DET :
This product has a feature that allows you to observe
movement of objects in 8 different areas on the
screen, and the words 'MOTION DETECTED' appear on
the screen when movement is detected.
you can monitor activity more efficient.
Operating Your Camera

When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates ’MOTION DET‘.

Set up the mode using the Function Setup switch.
   -SENSITIVITY:Youcanselectupto8MDareas.WhenSENSITIVITYnumberishigh,motion
detectionsensitivityisincreasedtorecognizeevensmallmovement.
   -AREAMODE:DetermineswhethertousetheMDareaselectedinSENSITIVITY.
   -SELPOS:Determineswhichofthe4verticesofeachMDareaistobeused.
   -YPOS:DeterminesthecoordinateoftheverticalaxisforSELPOS.
   -XPOS:DeterminesthecoordinateofthehorizontalaxisforSELPOS.
- FILL SET:FillsinaselectedMDarea.Thecoloroffillingissequentiallyselectedasbrown,
orange, blue, cyan, yellowish green, yellow and red.
   -RETURN:SelectthistosavetheMOTIONDETmenusettingsandreturntotheSPECIALmenu.
•MDareasshowonlyMOTIONDETmenu.Therefore,MDareasdon’tdisplayonthe
monitor screen.
Notes
 -AREASEL:Youcanselectupto8PRIVACYareas.
 -AREAMODE:Determineswhethertousetheareaselected
intheAREASEL, and thesizeandposition
of the area.
 -MASKCOLOR:Determinesareacolor.YoucanselectGray,
Green,Red,Blue,Black,White.
 -TRANSP:Determinethe transparency of selected areaas
controllingnumberfrom0to3.
 -RETURN:SelectthistosavethePRIVACYmenusettingsandreturntotheSPECIALmenu.
- MASKCOLOR:Determineareacolor.YoucanselectGray,Green,Red,Blue,Black,White.
 -TRANSP:Determinethetransparencyofselectedareaascontrollingnumberfrom0to3.
 -RETURN:Select this to save the PRIVACYmenu settings and returntotheSPECIAL
menu.
• WhenusingACpowerat60Hz(PAL:50Hz)frequency,youcanusetheL/Ltypesynchronization.
•WhenthepowerisDC12V,theSYNCmenuisfixedtothe‘INT’mode.
Notes
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
• You can decide the synchronization between luminance and color signal when
select the 'Mode' to TRACE.
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.
•ThechanceofresolutiondecreaseisexistedbecauseDISfunctionusesthedigitalzoom.
•DISdoesn ’ toperatewhenbackgroundilluminationistoolow.
•DISdoesn ’ toperatewhenobjectpatternismonotonicaslikeskyorwhitewall.
•IfDISisenabled,thedigitalzoomisnotconfiguredtolessthan46level.
Notes
COMM ADJ (Communication Adjustment):
This function sets up the camera communication status
when controlling the camera through an external control
device.

COLOR DOME CAMERA User’s Manual
28
COLOR DOME CAMERA User’s Manual
29
● The image on the screen is dark.
▶ Adjustthecontrastfeatureofthemonitor.
▶ Ifyouhaveanintermediatedevice,setthe75Ω/Hi-zproperly.
● The camera is not working properly, and the surface of the camera is hot.
▶ Check that you have properly connected the camera to an appropriate power source.
● The DAY/NIGHT menu does not work.
▶ CheckthatAGCofEXPOSURESETUPmenuis‘OFF’.
● The SENS-UP function does not work.
▶ CheckthatAGCofEXPOSURESETUPmenuis‘OFF’.
▶ CheckthatSHUTTERofEXPOSURESETUPmenuis‘A.FLK’.
● The Motion Detection function does not work.
▶ CheckthatMOTIONDETofSPECIALSETUPmenuis‘OFF’.
● Color is not correct.
▶ CheckthesettingofWHITEBALSETUPmenu.
● The screen flickers continually.
▶ Check that direction of camera turns toward the Sun.
● RS-485 communication fails.
▶ Check the polarity between RS-485ControlPortandRS-485cable.
▶ ChecktheRS-485Communicationestablishmentinitialvalue
▶ Werecommendthatyoumakeground connect between camera and controller in order to maintain
safety communication control.
  
When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates ‘COMM ADJ’.
  
Set up the mode using the Function Setup switch.
 -CAMID:Determinesthecamera'sidentificationnumber(between0and255).
 -BAUDRATE:Youcanselect2400/4800/9600/19200/38400/57600bps.
 -UARTMODE:YoucanselectNONE,EVENorODDfortheparitybits.
 -RETPKT:Determineswhethertosendacommand backtothecontrollerdevicewhen a
communication control command is sent to the camera.
 -DISPCAMID:Displaycameratitleontopleftcornerofthescreen.
Operating Your Camera
Press the Function Setup switch in the EXIT menu to save the current settings and exit the
MAIN SETUP menu.
LANGUAGE : You can select the menu language according to your requirements.
RESET : Resets the camera settings to the factory defaults. Communication
status and language is not initialized.
RETURN :
Select this to save the SPECIAL menu settings and return to the MAIN SETUP
menu.
EXIT
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
* RS-485 Communication establishment initial value
Item Camera ID BAUD RATE UART MODE RET PKT
Initial value 19600 8-NONE-1 ENABLE
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTION TERMINAL (TRX+) 485+
( -) CONNECTION TERMINAL (TRX-) 485-
●
Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera and monitor are fixed properly.
▶ CheckthatyouhaveproperlyconnectedVIDEOcabletothecameraVIDEOoutputjack.
● The image on the screen is dim.
▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶ Set the monitor to proper condition.
▶ If the camera is exposed to too strong light, change the camera position.
Troubleshooting
Dimension Ø141.2
R48
108mm
105.5mm

COLOR DOME CAMERA User’s Manual
30
COLOR DOME CAMERA User’s Manual
31
Specifications
DECLARATION OF CONFORMITY
ApplicationofCouncilDirective(s) 89/336/EEC
Manufacturer'sName SAMSUNGTECHWINCO.,LTD
Manufacturer'sAddress SAMSUNGTECHWINCO.,LTD
 42,SUNGJU-DONGCHANGWON-CITY,
 KYUNGNAM,KOREA,641-716
EuropeanRepresentativeName
EuropeanRepresentativeAddress
EquipmentType/Environment CCTVCamera
ModelName SID-462P/WP
BeginningSerialNO. S8100001
YearofManufacture 2008.12.01
Conformanceto EN50081-1:1992
 EMC-Directive89/336EECand92/31/EEC
 EN50130-4:1996
We, the undersigned, hereby declare that theequipmentspecifiedaboveconforms
totheaboveDirective(s).
Manufacturer SAMSUNGTECHWINCO.,LTD LegalRepresentativeinEurope
Signature  Signature
FullName HANSEUGKIM FullName
Position QUALITYCONTROLMANAGER Position
Place CHANGWON,KOREA Place
Date 2008.12.01 Date
SID-462(W)N SID-462(W)P
ELECTRICAL
Input Voltage AC 24V / DC 12V
Power Consumption Max 3.5W
VIDEO
Imaging Device 1/3 inch, Diagonal 6mm Super HAD CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Scanning System 2:1 Interlace
Synchronization Internal / Line Lock
Frequency H:15.734KHz / V:59.94Hz H:15.625KHz / V:50.00Hz
Horizontal Resolution 580TV Lines (Min.)
Min. Illumination Color : 0.15Lux (50 IRE @F1.2), 0.0006Lux (SENS-UP, x256)
S/N (Y Signal) 52dB
Video Output CVBS : 1.0Vp-p / 75Ω
LENS
Zoom Ratio 3.6x (Manual)
Focal length 2.8 ~ 10.0mm (F1.2)
Max. Aperture Ratio 1:1.2(Wide) ~ 2.8(Tele)
Angular Field of View H : 94.4°(Wide) ~ 28°(Tele) / V : 69.2°(Wide) ~ 21°(Tele)
PAN / TILT / ROTATE
Pan / Tilt / Rotate Range 0° ~ 340° / 0° ~ 146° / 0° ~ 340°
OPERATIONAL
Electronic Shutter Speed Fixed(NTSC:1/60, PAL:1/50), A.FLK
On Screen Display Built-in (Multi-language support)
Backlight Compensation BLC / HLC / Off
Day & Night Color / B/W / Auto (Electrical)
Gain Control Low / High / Off
White Balance ATW / AWC / Manual / Indoor / Outdoor
SENS-UP (frame Integration) On / Off (Selectable limit x2 ~x256)
Motion Detection On / Off (8 Programmable zones)
Privacy Masking On / Off (8 Programmable zones)
3D Noise Filter (SSNRII) On / Off (1 ~ 32 Level)
Digital Zoom On / Off (x2 ~ x10)
Digital Image Stabilization(DIS) On / Off
Camera Title On / Off
Sharpness On / Off
Flip / Mirror On / Off
Communication RS-485 (Baudrate 2400, 4800, 9600, 19200, 38400, 57600 bps Selectable)
Protocol Samsung Techwin Protocol, Pelco-D
ENVIRONMENTAL
Operating Temperature / Humidity -10°C ~ +50°C / 30% ~ 80% RH
MECHANICAL
Dimension / Weight Ø141.2 x 105.5mm / 545g
※SID-462WN, SID-462WP : Ivory color base model

P/No. : Z6806-0931-01C
VAN 08. 12
www.samsungtechwin.com
www.samsungcctv.com
•SAMSUNG TECHWIN CO.,LTD.
145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea
TEL : [phone]~8 FAX : [phone]
•SAMSUNG OPTO-ELECTRONICS UK,LTD.
Samsung House, 1000 Hillswood Drive, Hillswood
Business Park Chertsey Surrey KT16 OPS
TEL : [phone] FAX : [phone]
•SAMSUNG TECHWIN AMERICA,LTD.
1480 Charles Willard St. Carson, CA 90746, UNITED STATES
TEL : [phone] FAX : [phone]
SALES NETWORK