Samsung SID-47 User manual

Outstanding
Image of 580TVL
High Resolution Day & Night Dome Camera SID-47/48/49 User’s Manual
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH

This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the
equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
Before operating the camera, confirm the camera model and proper input power
voltage. In order to that you can understand this manual thoroughly, we'll introduce our
model description.
n SID-47/48/49 SERIES
 •NTSCMODEL
  SID-47(W)N/48(W)N/49(W)N
 •PALMODEL
  SID-47(W)P/48(W)P/49(W)P
nMODEL DESCRIPTION
 •SID-47(W)X/48(W)X/49(W)X
_ _
 •SIGNALSYSTEM
  NNTSCMODEL
  PPALMODEL
 •CAMERACOLOR
SILVERCOLOR
  WIVORYCOLOR
SIGNALSYSTEM
CAMERACOLOR

COLOR DOME CAMERA User’s Manual
4
COLOR DOME CAMERA User’s Manual
5
Contents
Contents
• Precautions …………………………………………………………………… 7
• Components and Accessories …………………………………………… 8
• Overview ………………………………………………………………………… 9
• Installation ……………………………………………………………………… 10
nInstallation
 
n Adjustthepanningandtilting,rotatingwhilewatchingthemonitor 
• Connection ……………………………………………………………………… 13
nConnectingToMonitor
  

nConnectingToPower
 
• Menu Configuration ………………………………………………………… 14
• Menu Setup …………………………………………………………………… 15
nLensShade
 

nExposure
 
nWhiteBalance
  

nBacklight
 
nSSNR
 

nDay/Night
 
nImageAdj
  

nSpecial
 
nExit
 
• Troubleshooting …………………………………………………………… 28
• Specifications ……………………………………………………………… 29
• Dimension …………………………………………………………………… 30
Features
Excellent Sensitivity
Thebuilt-inhighsensitivityCOLORCCDenablea
clearimageevenin0.15Lux(COLOR), 0.0006
Lux(Color,SENS-UPx256)orlowerillumination.
Day & Night
The camera identifies whether it is day or night and
automatically switches to the appropriate mode,
depending on its environment. By day, the camera
switches to color mode in order to maintain optimal
color.Atnight,itswitchestoB/Wmodesoasto
obtain better picture definition.
DIS (Digital Image Stabilizer)
TheDISfunctioncompensatesforanycamera
movement, to produce more stable pictures.
3-Axis camera mechanism
TheSID-47/48/49isespeciallyincrediblyflexibleto
installwithits3-axiscameraconstruction,which
makes the camera wall or slope mountable.
Miscellaneous Functions
HLC(HighLightCompensation),SENS-UP,FLIP(H/
V-REV),D-ZOOM,SHARPNESS,MOTIONDETECTION
andPRIVACYfunctionsareprovided.
Lens Shading Compensation
LENSSHADEdiminishesbrightnesscontrastto
obtain balanced view in the monitor.
OSD
Thecameracontrolisconvenientbyusing8
differentforeignlanguageO.S.D.
-NTSC:Korean,English,Spanish,Japanese,French
-PAL:English,French,German,Spanish, Italian,
Chinese
Electronic IRIS
ElectronicIRISisforcontrollingautomaticallyan
adjustableirisintherangeof1/60(PAL:1/50)~
1/120,000seconds.
SSNR (Samsung Super Noise
Reduction) Function
ThehighperformanceW-IVDSPchipdramatically
reduces the gain noise in digital image processing,
producing clear, sharp images in low lighting
environments.
Ultra High Resolution
Byadoptinga diagonal6mm(1/3")410,000(NTSC)
pixels,470,000(PAL)pixelsSONYCCD,thecamera
produces clear picture quality with a horizontal
resolutionof580TVlinesforcolor and700TVlines
forBW.

COLOR DOME CAMERA User’s Manual
6
COLOR DOME CAMERA User’s Manual
7
SamsungTechwincaresfortheenvironmentatallproductmanufacturing
stages to preserve the environment, and is taking a number of steps to provide
customerswithmoreenvironment-friendlyproducts.TheEcomarkrepresents
SamsungTechwin'swilltocreateenvironment-friendlyproducts,andindicates
thattheproductsatisfiestheEURoHSDirective.
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise.Pleasereaditcarefullyandusetheproductaccordingly.
 *Forproductinquiries,pleasecontacttheretailshopwhereyouboughtthecamera.Theuseofequipmentsuchas
anaerialladderwhileprovidingafter-salesserviceshallbeatyourexpense.
 *Separatethepowerplugwhenthundercrashesorlightingflashes.
 *Thisproductissupportequipmentforsurveillancesystem.Therefore,wecan'tcompensateformateriallossand/or
personalinjuriesbyrobbery,fire,naturaldisasterorsomethinglikethistype.
Ignoring this information may
resultinmateriallossand/or
seriouspersonalinjuriesincluding
death.
Indicates"NeverAllowed."
Ignoring this information may
resultinmateriallossand/ora
slightinjuries.
Indicates"NoDisassembling."
Warnings & Cautions
Warning/Attention/Special Mark Messages
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Severe lighting changes or flickering may hinder
normal camera operation.
May lower image quality.
Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
Avoid touching the camera lens.
Do not drop the camera or subject
it to physical shock.
May damage the CCD.May cause a product malfunction.
Never keep the camera face to
strong light directly.
Do not install under unstable
lighting conditions.
Precautions

COLOR DOME CAMERA User’s Manual
8
COLOR DOME CAMERA User’s Manual
9
Overview
Precautions
•Ifthecameraisexposedtospotlightorobjectreflectingstronglight,smearor
blooming may occur.
•Pleasecheckthatthepowersatisfiesthenormalspecificationbeforeconnecting
the camera.
Notes
Do not expose the camera to
radioactivity.
❶
SID-47/48/49
2
InstructionManual
3
M4TappingScrew3EA
4
8mmLens(forSID-49N/P)
If it is exposed to radioactivity, For heated CCD, it
will be out of order.
Components and Accessories
❶Pan Base : control panning angle of camera
2Rotate Base : control rotating angle of camera
3Tilt Base : control tilting angle of camera
4Lens Module : SID-47N/P - f=3.7mm, F2.0
SID-48N/P - f=8.0mm, F2.0
SID-49N/P - f=3.7mm, F2.0 (Additional Lens : f=8.0mm, F2.0)
5Power Input Connector
6Video Output Jack
7Function Setup Switch : display the menu on the screen and move the cursor to four
directions to confirm status or after changing a selected
item.
8Dome Cover
❶4 23
❶24
3
5
6
8
7

COLOR DOME CAMERA User’s Manual
10
COLOR DOME CAMERA User’s Manual
11
1) Separate the dome cover by counterclockwise rotation.
2) Separate the shield case by pulling from the camera body.
•Theinstallationshould bedone byqualified
service personnel or system installers.
•Iftheceilingmaterialisnotstrongenoughto
hold the installation screws, the camera may
falloff.Reinforcetheceilingasneeded.
•Tochangethepositionofthecable,take
awaytheHoleCoverandpassthecable
through.
Notes
* To install the dome cover on the camera
body, turn the latches in locking direction
as shown in the figure 1.
Installation
Installation
When using the Ceiling bracket
1) Hold the ceiling bracket (located where the arrow
points to) and separate it from the main body of
the camera by rotating it counterclockwise.
(refer to the picture in 'Notes' on page 8)
2) Place the separated ceiling bracket so that the
“Front” side faces the area to be monitored and
install it with the M4 tapping screws.
3) To combine the main body with the ceiling bracket,
make sure that the pan base fixation screw face the
opposite side of the “Front” side of the ceiling
bracket and rotate it clockwise.
4)Adjust the camera lens to face the area to be
monitored and fix the main body and the dome
cover by aligning the grooves and rotating the
body clockwise.
When changing the additional lens.
1) Loosen the lens hold screw at the side of lens holder.
2) Separate the built-in lens by counterclockwise rotation
and combine another lens. When combining the lens,
please clean the back side of lens and inside of the lens
holder.
3) Combining the lens by clockwise rotation, adjust the focus while watching the monitor.
• Ifyouwanttoinstallthecamerawiththeceilingbracketcombined,fixitusingtwoM4tapping
screwsatthesideofthemainbody(refertothe[Figure-2]onpage11).
Notes
Installation
Latch
[Figure-1]
LockingDirection
(Clockwise)
DomeCover
Unlockingdirection
(Counterclockwise)
MainBody
(Camera)
Originalpositionof
the cable
HoleCover
Unlocking
direction
M4tapping
screw (provided)
Anarrowforinstalling
directions
DomeCover
Ceilingbracket
Lockingdirection
Lenshold
screw
[Figure-2]
M4tapping
screw
PanBase
fixation
screw

COLOR DOME CAMERA User’s Manual
12
COLOR DOME CAMERA User’s Manual
13
1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.
 •PanBasemovesby176°toeachsidedirectionand352°onthewhole.
 •TiltBasecovers75˚angle.
 •RotateBasemovesby174°toeachsidedirectionand348°onthewhole.
2) Methods of adjustment
 •Thecaseofwallinstallation
1 After mounting the camera on a wall, adjusting the panning angle so that the camera can
face the direction to monitor when tilting.
2 And then adjust the tilting angle by rotating the tilt base.
3 Loosen the rotate base hold screw and adjust rotate base for the best monitoring.
4 Tighten tilt and pan base hold screw.
 •Thecaseofceilinginstallation
1 After mounting the camera on a ceiling, adjusting the panning angle for better monitoring
area by rotating the pan base.
2 And then adjust the tilting angle by rotating the tilt base.
3 Loosen the rotate base hold screw and adjust rotate base for the best monitoring.
4 Tighten tilt and pan base hold screw.
Adjust the panning and tilting, rotating while watching the monitor
Installation
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
• As the connecting method varies with the instruments, refer to the manual supplied with the
instrument.
• Only connect the cable when the power is turned off.
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
Connect the adaptor to the power input connector as shown in the figure below. The
recommended adaptor specification for SID-47N/47P, SID-48N/48P, SID-49N/49P is AC 24V / 300mA
or DC 12V / 500mA.
Connection
Connecting to Monitor
Connecting to Power
75˚
176˚
174˚ 174˚
176˚
Pan Base
Tilt Base
Rotate Base
CCTVCamera
Intermediate End monitor
CCTVCamera
Monitor
----PowerInputTerminal
4) When an image on the screen is in focus, tighten the lens hold screw with proper strength so
as not to break out the screw.
5) Please change the EFL in LENS SAHDE menu after changing the lens, so that the function
operates properly.
* Please use a suitable screwdriver for the size of screw.

COLOR DOME CAMERA User’s Manual
14
COLOR DOME CAMERA User’s Manual
15
FunctionSetupswitch
Operating Your Camera
• As shown in the table above, voltage decreases as the wire gets longer. Therefore
use of an excessively long adaptor output line for connection to the camera may
affect the performance of the camera.
*Standard voltage for camera operation : AC 24V ±10% / DC 12V ±10%
*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
•Besuretoconnectpoweronlyafteralltheinstallationiscomplete.
•NotethatAC/DCadaptorisnotsuppliedwithcamera.
•GroundshouldbeconnectedtotheGNDterminal.
Notes
When the resistance value of copper wire is at [20°C(68°F)]
Menu Configration
Menu Setup
Copper wire size (AWG) #24(0.22mm2)#22(0.33mm2)#20(0.52mm2)#18(0.83mm2)
Resistance (Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
Setup Menu
LENS SHADE
ON  OFF
EXPOSURE
 SHUTTER  AGC  SENS-UP
 RETURN
WHITE BALANCE
 ATW  MANUAL  AWC → SET
 OUTDOOR  INDOOR
BACKLIGHT
BLC HLC OFF
SSNR
 ON  OFF
DAY/NIGHT
 COLOR  B/W  AUTO
IMAGE ADJUSTMENT
(IMAGE ADJ.)
 V-REV  H-REV  D-ZOOM
 SHARPNESS  RETURN
SPECIAL
CAMTITLESYNC MOTION DET
PRIVACYDISLANGUAGE
RESET RETURN
EXIT
Connection
Use the Function Setup switch beside of the lens.
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT COLOR
7.IMAGE ADJ
8.SPECIAL
9.EXIT
Selectthefunctionby
moving up or down direction
of function setup switch.
Changethestatusby
moving right or left
direction of function
setup switch.
•Anitemwiththe icon also has sub menus. To select a sub menu, select an item with the icon
andpresstheFunctionSetupswitch.
•Anitemwiththe---iconisunavailableduetofunctionsettings.
Notes

COLOR DOME CAMERA User’s Manual
16
COLOR DOME CAMERA User’s Manual
17
- OFF: LENS SHADE NOT IN USE
- ON: LENS SHADE IN USE
- EFL : You can choose Effective Focal length of lens.
(3mm, 3.7mm, 6mm, 8mm)
- Default setting value of EFL
· SID-47N/P : 3.7mm
· SID-48N/P : 8.0mm
· SID-49N/P : 3.7mm
- SHADE GAIN: Please adjust brightness gain on the
fringe of monitor.
1. When the SETUP menu screen is displayed, select
EXPOSURE by using the Function Setup switch so that
the arrow indicates 'EXPOSURE'.
2. Select a desired mode using the Function Setup switch.
•ChangeEFLonlywhenyouchangelenses.
•Applicablelenses:F2.0,EFL=3.0mm,3.7mm,6mm,8mm.
• ThebiggerSHADEGAINcanmakethebrighterfringeareabutalsothemoreimagedistortionandnoise.
Notes
Operating Your Camera
EXPOSURE
LENS SHADE diminishes brightness contrast to obtain balanced view in the monitor.
LENS SHADE
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
 SHUTTER : You can select either auto or manual shutter.
- A.FLK : Select this when you experience picture flicker, which can happen when
there is a clash with the frequency of the installed lighting.
- ESC : Select this to control the shutter speed automatically. If ESC is selected, the
shutter speed is automatically controlled depending on the ambient
illumination of the subject.
- MANUAL : You can control shutter speed manually.
 AGC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen - but the higher the noise.
- OFF : Deactivates the AGC function.
  -LOW:Allowsautomaticgaincontrolfrom5.3dBto32dB.
  -HIGH:Allowsautomaticgaincontrolfrom5.3dBto37dB.
 SENS-UP :
When it is night or dark, the camera automatically
detects the light level and maintains a clear picture if
this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO :Activates the SENS-UP function.
RETURN :
Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
•IfyoupresstheFunctionSetupswitchin‘AUTO’mode,Youcanadjustbrightnessby
adjustingtheSENS-UPlevel.(x2~x256)
•NotethatthehighertheSENS-UPlevel,thebrighterthescreen,butthemorelikely
itisthatanafter-imagewillappear.
•Although Noise,Spots,andWhitishsymptomsmayoccurin SENS-UPoperation
whenthesens-uplevelisincreased,thisisnormal.
Notes

COLOR DOME CAMERA User’s Manual
18
COLOR DOME CAMERA User’s Manual
19
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
Operating Your Camera
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Function
Setup switch so that the arrow indicates ‘White Bal.’.
2. Select a desired mode using the Function Setup switch.
 Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,800°K and 10,500°K.
INDOOR :
Select this when the color temperature is between 4,500°K and 8,500°K.
OUTDOOR :
Select this when the color temperature is between 1,800°K and 10,500°K.
(sodium light inclusion)
AWCSET :
To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the Function Setup switch. If the environment changes, readjust it.
•WhiteBalancemaynotworkproperlyunderthefollowingconditions.InthiscaseselecttheAWC
mode.
1
Whenthecolortemperatureofenvironmentsurroundingthesubjectisoutofthecontrolrange
(e.g. clear sky, or sunset)
2
Whentheambientilluminationofthesubjectisdim.
3
 If the camera is directed towards a fluorescent light or is installed in a place where illumination changes
dramatically,theWhiteBalanceoperationmaybecomeunstable.
Notes
MANUAL :
Select this to fine-tune White Balance
manually. Set White Balance first by using the
ATW or AWC mode.After that switch to
MANUAL mode, fine-tune the White Balance
and then press the Function Setup switch.
White Balance (White Bal.)
This camera is designed so that it delivers a distinctive subject and background at the
same time, even when the subject is in backlight, unlike conventional cameras, by
adopting a proprietary W-IV DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates BACKLIGHT .
BACKLIGHT
ON OFF
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
2. Select a desired mode using the Function Setup switch depending on the camera
purpose.
BLC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
HLC (High Light Compensation) :
If there is a high light installed in a limited environment such as an apartment
parking garage or gas station entrance, removing the high light makes it possible to
view car license plates efficiently.
- DAY : In normal daylight conditions, the HLC is not activated.
- NIGHT : If a high light that is larger than a certain size is present on the screen,
remove the high light to see license plates clearly.

COLOR DOME CAMERA User’s Manual
20
COLOR DOME CAMERA User’s Manual
21
Operating Your Camera
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the switch.
•BecausetherecanbeadifferenceintheeffectivenessofHLCaccordingtotheamountof
lightareainthescreen,optimizetheinstallationangleforthebestHLCperformance.
•Ina darkenvironment,the HLCis onlyactivatedwhena highlightthat islarger thana
certain area is present.
•TheHLCisnotactivatedinlightoroverlydarkconditions.
Notes
Select ‘BLC’ to adjust the area to be
enhanced and enhancement level.
HLC : Enables a user to select a mask
color of high light area from a
picture.
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select 'SSNR' by using the Function
Setup switch so that the arrow indicates 'SSNR' .
SSNR
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT COLOR
2. Select a desired mode using the Function Setup switch.
Deactivates SSNR so that noise is not reduced.
OFF :
Deactivates SSNR so that noise is not reduced.
ON : Activates SSNR so that noise is reduced.
3. Set the SSNR mode to 'ON' and press the Function
Setup switch. Then you can adjust the noise reduction
level.
2. Select a desired mode using the Function Setup switch according to the picture display
you want.
•YoucannotsettheSSNRto'ON'or'OFF'whentheAGCmodeoftheEXPOSURE
menuis'OFF'.
•WhenadjustingthenoisereductionleveloftheSSNRmode,rememberthatthe
higher the level set, the more the noise level will be reduced but that after image
may also occur.
Notes
DAY/NIGHT
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT COLOR
7.IMAGE ADJ
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the
Function Setup switch so that the arrow indicates DAY/NIGHT.

COLOR DOME CAMERA User’s Manual
22
COLOR DOME CAMERA User’s Manual
23
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
AUTO :The mode is switched to Color in a normal
environment, but switches to B/W mode when
ambient illumination is low.To set up the
switching time for AUTO mode, press the Function
Setup switch.
- DWELL TIME : You can select the duration time about changing the day/night
mode.
5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
Operating Your Camera
•YoucannotcontroltheDAY/NIGHTmenuwhenAGCintheEXPOSUREmenuis‘OFF’.At
thistime,theexchangebetweenDAYmodeandNIGHTmodeoperatesaslikeselecting
‘COLOR’mode.
Notes
1. When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Function
Setup switch so that the arrow indicates IMAGE ADJ.
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT COLOR
7.IMAGE ADJ
8.SPECIAL
IMAGE ADJ.
2. Select a desired mode using the Function Setup switch.
V-REV :You can flip the picture vertically on the screen.
H-REV : You can flip the picture horizontally on the screen.
D-ZOOM : You can use a digital zoom of x2~x10.
SHARPNESS : As you increase this value, the picture
outline becomes stronger and clearer. Adjust
this value appropriately depending on the
sharpness of the picture.
RETURN : Select this to save the settings for the IMAGE
ADJ. menu and to return to the SETUP menu.
•WhentheV-REVorH-REVmodeisenabled,thetextonthescreendoesnotflip.
•IfyouincreasetheSHARPNESSleveltoohigh,thepicturemaybecomedistortedornoise
may appear.
Notes
IMAGE SETUP
1. V-REV OFF
2. H-REV OFF
3. D-ZOOM OFF
4. SHARPNESS ON
5. RETURN
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function
Setup switch so that the arrow indicates ‘SPECIAL’.
SPECIAL

COLOR DOME CAMERA User’s Manual
24
COLOR DOME CAMERA User’s Manual
25
Operating Your Camera
MAIN SETUP
1.LENS SAHDE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT COLOR
7.IMAGE ADJ
8.SPECIAL
9.EXIT
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
5. DIS OFF
6. LANGUAGE ENGLISH
7. RESET
8. RETURN
2. Select a desired mode using the Function Setup switch.
•WhentheCAMTITLEmenuis‘OFF’,notitle
will be displayed on the monitor screen
even if you enter one.
•OnlyEnglishisavailableinthemode.
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
Notes
CAM TITLE : If you enter a title, the title will appear on the monitor.

If the SPECIAL menu screen is displayed, use the Function Setup switch so that
the arrow indicates ‘CAM TITLE’.

Set it to ‘ON’ by using the Function Setup switch.

Enter a title, move the cursor to ’POS’ and press the
Function Setup switch. The entered title appears on
the screen. Select the position to display the title on
the screen by using the Function Setup switch and
press. When the position is determined, select ’END’
and press the Function Setup switch to return to the
SPECIAL menu.
•IfyoumovethecursortoCLRandpresstheFunctionSetupswitch,alltheletters
are deleted. To edit a letter, change the cursor to the bottom left arrow and press
theFunctionSetupswitch.Movethecursoroverthelettertobeedited,movethe
cursortothelettertobeinsertedandthenpresstheFunctionSetupswitch.
Notes
❸Press the Function Setup switch.
❹ Use the Function Setup switch to move
to a desired letter and select the letter
by pressing the switch. Repeat this to
enter multiple letters. You can enter up
to 15 letters.
SYNC :
In areas where the supply is at 60Hz, you can
synchronize the output phase of multiple cameras
using the power synchronization function (Line-
Lock) without using a synchronization signal
generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock

Press the Function Setup switch.

Youcanselectadesiredphasefrom0to359whenselect'phase'.
❸
You can decide the synchronization between power frequency and color signal when select the
'Mode'toTRACE.
FRONT DOOR
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
CLR POS END

COLOR DOME CAMERA User’s Manual
26
COLOR DOME CAMERA User’s Manual
27
MOTION DET :
This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen,
and the words 'MOTION DETECTED' appear on the
screen when movement is detected. You can monitor
activity more efficient.
Operating Your Camera
•MDareasshowonlyMOTIONDETmenu.Therefore,MDareasdon’tdisplayonthe
monitor screen.
Notes
•WhenusingACpowerat60Hz(PAL:50Hz)frequency,youcanusetheL/Ltypesynchron
ization.
•Ifthechangethesynchronizationsettingto"L/L"synchronizationtypewhencolor
rolling appears, the frequency of the lamp and the camera power is synchronized to
remove the color rolling.
Notes

When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates 'MOTION DET'.

Set up the mode using the Function Setup switch.
 -SENSITIVITY:Youcanselectupto8MDareas.WhenSENSITIVITYnumberishigh,
motion detection sensitivity is increased to recognize even small
movement.
 -AREAMODE:DetermineswhethertousetheMDareaselectedinSENSITIVITY.
 -SELPOS:Determineswhichofthe4verticesofeachMDareaistobeused.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- FILL SET : Fills in a selected MD area. The color of filling is sequentially selected as brown,
orange, blue, cyan, yellowish green, yellow, magenta and red.
 -RETURN: Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
Press the Function Setup switch in the EXIT menu to save the current settings and exit the
MAIN SETUP menu.
EXIT
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.
LANGUAGE :
You can select the menu language according to your requirements.
RESET :
Resets the camera settings to the factory defaults. Language is not initialized.
RETURN :
Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu.
 -AREASEL:Youcanselectupto8PRIVACYareas.
 -AREAMODE:Determineswhethertousetheareaselected
intheAREASEL,and thesize andposition
of the area.
 -MASKCOLOR:Determinearea color.YoucanselectGray,
Black and White
 -TRANSP:Determinethetransparency ofselectedareaas
controllingnumberfrom0to3.
 -RETURN:SelectthistosavethePRIVACYmenusettingsandreturntotheSPECIALmenu.
PRIVACY : Hide an area you want to hide on the screen.
  
When the SPECIAL menu screen is displayed, press
the Function Setup switch so that the arrow
indicates ‘PRIVACY’.
  
Set up the mode using the Function Setup switch.
•ThechanceofresolutiondecreaseisexistedbecauseDISfunctionusesthedigitalzoom.
•DISdoesn’toperatewhenbackgroundilluminationistoolow.
•DISdoesn’toperatewhenobjectpatternismonotonicaslikeskyorwhitewall.
•IfDISisenabled,thedigitalzoomisnotconfiguredtolessthan46level.
Notes

COLOR DOME CAMERA User’s Manual
28
COLOR DOME CAMERA User’s Manual
29
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
●
Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera and monitor are fixed properly.
▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
● The image on the screen is dim.
▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶ SetthemonitororDVRtopropercondition.
▶ If the camera is exposed to too strong light, change the camera position.
● The image on the screen is dark.
▶ AdjustthecontrastfeatureofthemonitororDVR.
▶ Ifyouhaveanintermediatedevice,setthe75Ω/Hi-zproperly.
● The camera is not working properly, and the surface of the camera is hot.
▶ Check that you have properly connected the camera to an appropriate power source.
● The DAY/NIGHT menu does not work.
▶ CheckthatAGCofEXPOSURESETUPmenuis‘OFF’.
● The SENS-UP function does not work.
▶ CheckthatAGCofEXPOSURESETUPmenuis‘OFF’.
▶ CheckthatSHUTTERofEXPOSURESETUPmenuis‘A.FLK’or‘MANUAL’.
● The Motion Detection function does not work.
▶ CheckthatMOTIONDEFofSPECIALSETUPmenuis‘OFF’.
● Color is not correct.
▶ Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶ Check that direction of camera turns toward the Sun.
Troubleshooting
Specifications
SID-47(W)N SID-47(W)P SID-48(W)N SID-48(W)P SID-49(W)N SID-49(W)P
ELECTRICAL
Input Voltage Dual (12V DC/ 24V AC)
Power Consumption 2.5W
VIDEO
Imaging Device 1/3” Super HAD CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V) 811(H) x 508(V) 795(H) x 596(V) 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V) 768(H) x 494(V) 752(H) x 582(V) 768(H) x 494(V) 752(H) x 582(V)
Scanning System 2 : 1 Interlace
Synchronization Internal / Line Lock
Frequency H :15.734KHz
V : 59.94Hz
H : 15.625KHz
V : 50Hz
H :15.734KHz
V : 59.94Hz
H : 15.625KHz
V : 50Hz
H :15.734KHz
V : 59.94Hz
H : 15.625KHz
V : 50Hz
Horizontal Resolution 580TV lines (Min.)
Min. Illumination 0.15Lux(50IRE @F1.2), 0.0006Lux (SENS-UP, x256)
S / N (Y signal) 52dB
Video Output CVBS : 1.0Vp-p / 75Ω
LENS
Focal Length 3.7mm 8.0mm 3.7mm, 8.0mm
Max. Aperture Ratio F2.0
Angular Field of View 3.7mm : 71°(H), 52°(V), 8mm : 33°(H), 25°(V)
PAN / TILT / ROTATE
Pan / Tilt / Rotate Range 0° ~ 352° / 0° ~ 75° / 0° ~ 348°
OPERATIONAL
Lens Shade On / Off
Electronic Shutter Speed ESC (NTSC:1/60 ~ 1/120,000sec, PAL:1/50 ~ 1/120,000sec) / Manual / A.FLK
On Screen Display Built-in (Multi-language support)
Backlight Compensation BLC / HLC / Off
Day & Night Color / B&W /Auto (Electrical)
Gain Control Low / High / Off
White Balance ATW / AWC / Manual / Outdoor / Indoor (1,800°K ~ 10,500°K)
SENS-UP (frame Integration) Auto / Off (Selectable limit x2 ~ x256)
Motion Detection On / Off (8 Programmable zones)
Privacy Masking On / Off (8 Programmable zones)
3D Noise Filter (SSNRII) On / Off (1 ~ 32 Level)
Digital Zoom On / Off (x2 ~ x10)
Digital Image Stabilization
(DIS) On / Off
Camera Title On / Off
Sharpness On / Off
Flip / Mirror On / Off
ENVIRONMENTAL
Operating Temperature / Humidity -10°C ~ +50°C / 30% ~ 80% RH
MECHANICAL
Dimension / Weight Ø107.6 x 83.7mm / 261g
※SID-47W/48W/49W : Ivory base model

COLOR DOME CAMERA User’s Manual
30
COLOR DOME CAMERA User’s Manual
31
DECLARATION OF CONFORMITY
ApplicationofCouncilDirective(s) 89/336/EEC
Manufacturer'sName SAMSUNGTECHWINCO.,LTD
Manufacturer'sAddress SAMSUNGTECHWINCO.,LTD
 42,SUNGJU-DONGCHANGWON-CITY,
 KYUNGNAM,KOREA,641-716
EuropeanRepresentativeName
EuropeanRepresentativeAddress
EquipmentType/Environment CCTVCamera
ModelName SID-47(W)P/48(W)P/49(W)P
BeginningSerialNO. S8100001
YearofManufacture 2008.10.01
Conformanceto EN50081-1:1992
 EMC-Directive89/336EECand92/31/EEC
 EN50130-4:1996
We,theundersigned,herebydeclarethatthe equipment specifiedaboveconforms
totheaboveDirective(s).
Manufacturer SAMSUNGTECHWINCO.,LTD LegalRepresentativeinEurope
Signature  Signature
FullName HANSEUGKIM FullName
Position QUALITYCONTROLMANAGER Position
Place CHANGWON,KOREA Place
Date 2008.10.01 Date
Ø107.6
R45
83.7mm
81.6mm
Dimension

P/No. : Z6806-09120-1B
VAN 08. 10
www.samsungtechwin.com
www.samsungcctv.com
•SAMSUNG TECHWIN CO.,LTD.
145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do, 462-120, Korea
TEL : [phone]~8 FAX : [phone]
•SAMSUNG OPTO-ELECTRONICS UK,LTD.
Samsung House, 1000 Hillswood Drive, Hillswood
Business Park Chertsey Surrey KT16 OPS
TEL : [phone] FAX : [phone]
•TIANJIN SAMSUNG OPTO-ELECTRONICS CO.,LTD.
No.9 ZHANGHENG STREET. MICRO-ELECTRONIC INDUSTRIAL
PARK JINGANG-ROAD TIANJIN, CHINA 300385
TEL : [phone] FAX : [phone]
•SAMSUNG TECHWIN AMERICA,LTD.
1480 Charles Willard St. Carson, CA 90746, UNITED STATES
TEL : [phone] FAX : [phone]
SALES NETWORK