Samsung SIR-60 User manual

High Resolution D/N IR Dome Camera SIR-60 User’s Manual
Thank you for purchasing a SAMSUNG Dome CAMERA.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH

This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the
equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
Before operating the camera, confirm the camera model and proper input power
voltage. In order to that you can understand this manual thoroughly, we'll introduce our
model description.
n SIR-60 SERIES
 •NTSCMODEL
  SIR-60N
 •PALMODEL
  SIR-60P
nMODEL DESCRIPTION
 •SIR-60(X)
_
 •SIGNALSYSTEM
  NNTSCMODEL
  PPALMODEL
SIGNALSYSTEM

COLOR DOME CAMERA User’s Manual
4
COLOR DOME CAMERA User’s Manual
5
Contents
Contents
• Precautions …………………………………………………………………… 7
• Components and Accessories …………………………………………… 8
• Overview ………………………………………………………………………… 9
• Installation ……………………………………………………………………… 10
nInstallation
 

•WhenusingtheCeilingbracket
 

n
Adjustthepanningandtiltingwhilewatchingthemonitor  
• Connection ……………………………………………………………………… 13
nConnectingToamonitor
  

nConnectingToaPowerSupply
  
• Operating Your Camera ……………………………………………………… 14
nMenuConfigration
  
nMenuSetup
  
•LensShade
 

•Exposure
 
•White Balance
 

•Backlight
 
•SSNR
 

•Day/Night
  

•ImageAdj
 

•Special
 
•Exit
  
• Troubleshooting …………………………………………………………… 28
• Specifications ……………………………………………………………… 29
• Dimension …………………………………………………………………… 30
Features
Excellent Sensitivity
TheBuilt-inhighsensitivityCOLORCCDenablesa
clearimageevenin 0Lux(B/W,IR-LED ON) orlower
illumination,
Day & Night
The camera identifies whether it is day or night and
automatically switches to the appropriate mode,
depending on its environment. By day, the camera
switches to color mode in order to maintain optimal
color.Atnight,itswitchestoB/Wmodesoasto
obtain better picture definition.
DIS (Digital Image Stabilizer)
TheDISfunctioncompensatesforanycamera
movement, to produce more stable pictures.
Indoor Visibility range 7M
InB/Wmode,theIR-LEDsareilluminated,theindoor
visibilityrangeat0Luxis7m
IR MODE Function
Miscellaneous Functions
TheintensityoftheIR-LEDsautomaticallyadjust
dependingupontheclosenessoftheobjectto
prevent saturation.
HLC(HighLightCompensation),SENS-UP,FLIP(H/
V-REV),D-ZOOM,SHARPNESS,MOTIONDETECTION
andPRIVACYfunctionsareprovided.
Lens Shading Compensation
LENSSHADEreducesthebrightnesscontrastto
obtain a more balanced image on the monitor.
OSD
The camera control is convenient by using 8
differentforeignlanguageO.S.D.
-NTSC:Korean,English,Spanish,Japanese,French
-PAL:English,French,German, Spanish,Italian,
Chinese
SSNR (Samsung Super Noise
Reduction) Function
ThehighperformanceW-IVDSPchipdramatically
reduces the gain noise in digital image processing,
producing clear, sharp images in low lighting
environments.
Ultra High Resolution
Byadoptingadiagonal 6mm(1/3") 410,000(NTSC)
pixels,470,000(PAL)pixels SONY CCD,thecamera
produces clear picture quality with a horizontal
resolutionof580TVlines for color and700TVlines
for BW.

COLOR DOME CAMERA User’s Manual
6
COLOR DOME CAMERA User’s Manual
7
SamsungTechwincaresfortheenvironmentatallproductmanufacturing
stages to preserve the environment, and is taking a number of steps to provide
customerswithmoreenvironment-friendlyproducts.TheEcomarkrepresents
SamsungTechwin'swilltocreateenvironment-friendlyproducts,andindicates
thattheproductsatisfiestheEURoHSDirective.
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise.Pleasereaditcarefullyandusetheproductaccordingly.
 *Forproductinquiries,pleasecontacttheretailshopwhereyouboughtthecamera.Theuseofequipmentsuchas
anaerialladderwhileprovidingafter-salesserviceshallbeatyourexpense.
 *Separatethepowerplugduringathunderstorm.
 *Thisproductissupportequipmentforsurveillancesystem.Therefore,wecan'tcompensateformateriallossand/or
personalinjuriesbyrobbery,fire,naturaldisasterorsomethinglikethistype.
Ignoring this information may
resultinmateriallossand/or
seriouspersonalinjuriesincluding
death.
Indicates"NeverAllowed."
Ignoring this information may
resultinmateriallossand/ora
slightinjuries.
Indicates"NoDisassembling."
Warnings & Cautions
Warning/Attention/Special Mark Messages
Do not install under extreme
temperatures.
Do not install in high humidity
environments.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Severe lighting changes or flickering may hinder
normal camera operation.
May lower image quality.
Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
Avoid touching the camera lens.
Do not drop the camera or subject
it to physical shock.
May damage the CCD.May cause a product malfunction.
Never point the camera directly at
a strong light.
Do not install under unstable
lighting conditions.
Precautions

COLOR DOME CAMERA User’s Manual
8
COLOR DOME CAMERA User’s Manual
9
Overview
Precautions
•Ifthecameraisexposedtospotlightsorobjectsreflectingbrightlight,smearingor
blooming may occur.
•Pleasecheckthatthepowersatisfiesthenormalspecificationbeforeconnecting
the camera.
Notes
Do not expose the camera to
radioactivity.
Do not use abrasive or opaque
substances on the dome cover.
❶
SIR-60
2
InstructionManual
3
M4TappingScrew3EA
If it is exposed to radioactivity, For heated CCD, it
will be out of order.
May reduce the performance of the camera.
Components and Accessories
❶Pan Base : control panning angle of camera
2Tilt Base : control tilting angle of camera
3Lens Module : f=3.6mm,F2.0(IR Lens)
4Power Input Connector
5Video Output Jack
6Function Setup Switch : displays the OSD menu and moves the cursor up, down,
left,and right amend or confirm changes.
7Dome Cover
❶23
❶3
2
4
5
7
6

COLOR DOME CAMERA User’s Manual
10
COLOR DOME CAMERA User’s Manual
11
1) Separate the dome cover by counterclockwise rotation.
•Theinstallationshould bedone byqualified
service personnel or system installers.
•Iftheceilingmaterialisnotstrongenoughto
hold the installation screws, the camera may
falloff.Reinforcetheceilingasneeded.
•Tochangethepositionofthecable,take
awaytheHoleCoverandpassthecable
through.
Notes
* To install the dome cover on the camera
body, turn the latches in locking direction
as shown in the figure 1.
Installation
Installation
When using the Ceiling bracket
1) Hold the ceiling bracket (located where the arrow
points to) and separate it from the main body of
the camera by rotating it counterclockwise.
(refer to the picture in 'Notes' on page 10)
2)Adjust the camera lens to face the area to be
monitored and fix the main body and the dome
cover by aligning the grooves and rotating the
body clockwise.
Installation
Latch
[Figure-1]
LockingDirection
(Clockwise)
MainBody
(Camera)
Originalpositionof
the cable
HoleCover
Unlocking
direction
M4tapping
screw (provided)
Anarrowforinstalling
directions
DomeCover
Ceilingbracket
Lockingdirection
[Figure-2]
PanBase
fixation
screw
M4
tapping
screw
DomeCover
•Ifyouwanttoinstallthecamerawiththeceilingbracketcombined,fixitusingtwoM4
tappingscrewsatthesideofthemainbody(refertothe[Figure-2]onpage11)
Notes

COLOR DOME CAMERA User’s Manual
12
COLOR DOME CAMERA User’s Manual
13
176˚
1) You can adjust the camera to point in any direction by using the pan, Tilt
mechanism.
 •PanBasecanrotatesby±176°(total352°)
 •TiltBasecovers75˚angle.
2) Methods of adjustment
 •Thecaseofwallinstallation
1 After mounting the camera on a wall, adjust the panning angle so that the correct
viewing angle is attained and the titling is correctly orientated.
2 Tighten pan and tilt securing screw.
 •Thecaseofceilinginstallation
1 After mounting the camera on a ceiling, adjust the panning angle so that the correct
viewing angle is attained and the titling is correctly orientated.
2 And then adjust the tilting angle by rotating the tilt base.
3 Tighten pan and tilt securing screw.
Adjust the panning and tilting while watching the monitor
Installation
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
• As the connecting method varies with the instruments, refer to the manual supplied with the
instrument.
• Only connect the cable when the power is turned off.
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
Connect the adaptor to the power input connector as shown in the figure below. The
recommended adaptor specification for SIR-60N/P is DC 12V / 500mA.
Connection
Connecting to Monitor
Connecting to Power
CCTVCamera
Intermediate End monitor
CCTVCamera
Monitor
----PowerInputTerminal
Tilt Base fixation screw
176˚
Pan Base fixation screw
75˚
•WhenyouwanttoadjustthePan/TiltBase,loosen,adjustandthentightenthe
Pan/TiltBasescrews.
Notes

COLOR DOME CAMERA User’s Manual
14
COLOR DOME CAMERA User’s Manual
15
FunctionSetupswitch
Operating Your Camera
• As shown in the table above, voltage decreases as the wire gets longer. Therefore
use of an excessively long adaptor output line for connection to the camera may
affect the performance of the camera.
*Standard voltage for camera operation : DC 12V ±10%
*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
•Besuretoconnectpoweronlyafteralltheinstallationiscomplete.
•GroundshouldbeconnectedtotheGNDterminal.
Notes
When the resistance value of copper wire is at [20°C(68°F)]
Menu Configration
Menu Setup
Copper wire size (AWG)
#24(0.22mm2)#22(0.33mm2)#20(0.52mm2)#18(0.83mm2)
Resistance (Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
Setup Menu
LENS SHADE
ON 
OFF
EXPOSURE

SHUTTER

AGC

SENS-UP

RETURN
WHITE BALANCE

ATW

MANUAL

AWC → SET

OUTDOOR

INDOOR
BACKLIGHT
BLC HLC OFF
SSNR

ON

OFF
DAY/NIGHT

COLOR

B/W

AUTO
IMAGE ADJUSTMENT
(IMAGE ADJ.)

V-REV

H-REV

D-ZOOM

SHARPNESS

RETURN
SPECIAL
CAMTITLE
SYNC MOTION DET
PRIVACY
DIS LANGUAGE
IR MODE RESET
RETURN
EXIT
Connection
Use the Function Setup switch beside of the lens.
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
Selectthefunctionby
moving up or down direction
of function setup switch.
Changethestatusby
moving the setup switch
left or right.
•Anitemwiththe icon also has sub menus. To select a sub menu, select an item with the icon
andpresstheFunctionSetupswitch.
•Anitemwiththe---iconisunavailableduetofunctionsettings.
Notes

COLOR DOME CAMERA User’s Manual
16
COLOR DOME CAMERA User’s Manual
17
- OFF: LENS SHADE NOT IN USE
- ON: LENS SHADE IN USE
1. When the SETUP menu screen is displayed, select
EXPOSURE by using the Function Setup switch so that
the arrow indicates 'EXPOSURE'.
2. Select a desired mode using the Function Setup switch.
Operating Your Camera
EXPOSURE
LENS SHADE diminishes brightness contrast to obtain balanced view on the monitor.
LENS SHADE
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
 SHUTTER : You can select either auto or manual shutter.
- A.FLK : Select this when you experience picture flicker, which can happen when
there is a clash with the frequency of the installed lighting.
- ESC : Select this to control the shutter speed automatically. If ESC is selected, the
shutter speed is automatically controlled depending on the ambient
illumination of the subject.
- MANUAL : You can control shutter speed manually.
 AGC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen - but the higher the noise.
- OFF : Deactivates the AGC function.
  -LOW:Allowsautomaticgaincontrolfrom5.3dBto32dB.
  -HIGH:Allowsautomaticgaincontrolfrom5.3dBto37dB.
 SENS-UP :
When it is night or dark, the camera automatically
detects the light level and maintains a clear picture if
this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO :Activates the SENS-UP function.
RETURN :
Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
•IfyoupresstheFunctionSetupswitchin‘AUTO’mode,Youcanadjustbrightnessby
adjustingtheSENS-UPlevel.(x2~x512)
•NotethatthehighertheSENS-UPlevel,thebrighterthescreen,butthemorelikely
itisthatanafter-imagewillappear.
•Although Noise,Spots, andWhitish symptomsmay occurinSENS-UPoperation
whenthesens-uplevelisincreased,thisisnormal.
Notes
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Function
Setup switch so that the arrow indicates ‘White Bal.’.
2. Select a desired mode using the Function Setup switch.
White Balance (White Bal.)
 Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,700°K and 11,000°K.
INDOOR :
Select this when the color temperature is between 4,500°K and 8,500°K.

COLOR DOME CAMERA User’s Manual
18
COLOR DOME CAMERA User’s Manual
19
Operating Your Camera
•WhiteBalancemaynotworkproperlyunderthefollowingconditions.InthiscaseselecttheAWC
mode.
1
Whenthecolortemperatureofenvironmentsurroundingthesubjectisoutofthecontrolrange
(e.g. clear sky, or sunset)
2
Whentheambientilluminationofthesubjectisdim.
3
 If the camera is directed towards a fluorescent light or is installed in a place where illumination changes
dramatically, the White Balance operation may become unstable.
Notes
MANUAL :
Select this to fine-tune White Balance
manually. Set White Balance first by using the
ATW or AWC mode.After that switch to
MANUAL mode, fine-tune the White Balance
and then press the Function Setup switch.
This camera is designed so that it delivers a distinctive subject and background at the
same time, even when the subject is in backlight, unlike conventional cameras, by
adopting a proprietary W-IV DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates BACKLIGHT .
BACKLIGHT
ON OFF
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
2. Select a desired mode using the Function Setup switch depending on the camera
purpose.
BLC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
HLC (High Light Compensation) :
If there is a high light installed in a limited environment such as an apartment
parking garage or gas station entrance, removing the high light makes it possible to
view car license plates efficiently.
- DAY : In normal daylight conditions, the HLC is not activated.
- NIGHT : If a high light that is larger than a certain size is present on the screen,
remove the high light to see license plates clearly.
OUTDOOR :
Select this when the color temperature is between 1,700°K and 11,000°K.
(sodium light inclusion)
AWCSET :
To find the optimal luminance level for the current environment, point the
camera towards a sheet of white paper and press the Function Setup
switch. If the environment changes, readjust it.
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the switch.
Select ‘BLC’ to adjust the area to be
enhanced and enhancement level.
HLC : Enables a user to select a mask
color of high light area from a
picture.
•BecausetherecanbeadifferenceintheeffectivenessofHLCaccordingtotheamountof
lightareainthescreen,optimizetheinstallationangleforthebestHLCperformance.
•Ina darkenvironment,the HLCis onlyactivatedwhen ahigh lightthat islarger thana
certain area is present.
•TheHLCisnotactivatedinlightoroverlydarkconditions.
•BLCfunctiondoesnotworkinD&NB/Wmode.
Notes

COLOR DOME CAMERA User’s Manual
20
COLOR DOME CAMERA User’s Manual
21
Operating Your Camera
This function reduces the background noise in a low luminance environments.
1. When the SETUP menu screen is displayed, select 'SSNR' by using the Function
Setup switch so that the arrow indicates 'SSNR' .
SSNR
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
2. Select a desired mode using the Function Setup switch.
Deactivates SSNR so that noise is not reduced.
OFF :
Deactivates SSNR so that noise is not reduced.
ON : Activates SSNR so that noise is reduced.
3. Set the SSNR mode to 'ON' and press the Function
Setup switch. Then you can adjust the noise reduction
level.
•YoucannotsettheSSNRto'ON'or'OFF'whentheAGCmodeoftheEXPOSURE
menuis'OFF'.
•WhenadjustingthenoisereductionleveloftheSSNRmode,rememberthatthe
higher the level set, the more the noise level will be reduced but that after image
may also occur.
Notes
DAY/NIGHT
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select‘DAY/NIGHT’by using the Up and
Down buttons so that the arrow indicates‘DAY/NIGHT’.
MAIN SETUP
1.LENS SHADE DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
2. Select a desired mode using the Left and Right buttons according to the picture display you want.
COLOR : The picture is always displayed in color (IR
LED : OFF)
B/W : The picture is always displayed in black and
white (IR LED : ON)
AUTO :The mode is switched to ’Color‘ in a normal
environment, but switches to B/W mode(IR LED
: ON) when ambient illumination is low.To set
up the switching time or speed for AUTO mode, press the SET button.
- DWELL TIME : Y ou can select the duration time about changing the day/night mode.
3s, 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
- DURATION : You can select the brightness level at which the camera switches from day to
night mode.
* Light levels are often site dependant.
Color B/W B/W Color
Fast 2.5 lux 5 lux
Slow 1lux 10 lux
• YoucannotcontroltheDAY/NIGHTmenuwhenAGCintheEXPOSUREmenuis‘OFF’.
Atthistime,theexchangebetweenDAYmodeandNIGHTmodeoperatesaslikeselecting
‘COLOR’mode.
•The OSD keydoes not workfor 3 secondswhen switching toColor or B/W,to ensure
stable camera operation.
Notes
EXTERN : This mode allows you to apply a desired filter to external signals.

COLOR DOME CAMERA User’s Manual
22
COLOR DOME CAMERA User’s Manual
23
Operating Your Camera
1. When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Function
Setup switch so that the arrow indicates IMAGE ADJ.
MAIN SETUP
1.LENS SHADE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
IMAGE ADJ.
2. Select a desired mode using the Function Setup switch.
V-REV :You can flip the picture vertically on the screen.
H-REV : You can flip the picture horizontally on the screen.
D-ZOOM : You can use a digital zoom of x2~x10.
SHARPNESS : As you increase this value, the picture
outline becomes stronger and clearer. Adjust
this value appropriately depending on the
sharpness of the picture.
RETURN : Select this to save the settings for the IMAGE
ADJ. menu and to return to the SETUP menu.
•WhentheV-REVorH-REVmodeisenabled,thetextonthescreendoesnotflip.
•IfyouincreasetheSHARPNESSleveltoohigh,thepicturemaybecomedistortedornoise
may appear.
Notes
IMAGE SETUP
1. V-REV OFF
2. H-REV OFF
3. D-ZOOM OFF
4. SHARPNESS ON
5. RETURN
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function
Setup switch so that the arrow indicates ‘SPECIAL’.
SPECIAL
MAIN SETUP
1.LENS SAHDE ON
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT
AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
5. DIS OFF
6. LANGUAGE ENGLISH
7. IR MODE ----
8. RESET
9. RETURN
2. Select a desired mode using the Function Setup switch.

COLOR DOME CAMERA User’s Manual
24
COLOR DOME CAMERA User’s Manual
25
Operating Your Camera
•WhentheCAMTITLEmenuis‘OFF’,notitle
will be displayed on the monitor screen
even if you enter one.
•OnlyEnglishisavailableinthemode.
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
Notes

Enter a title, move the cursor to ’POS’ and press the
Function Setup switch. The entered title appears on
the screen. Select the position to display the title on
the screen by using the Function Setup switch and
press. When the position is determined, select ’END’
and press the Function Setup switch to return to the
SPECIAL menu.
•IfyoumovethecursortoCLRandpresstheFunctionSetupswitch,alltheletters
are deleted. To edit a letter, change the cursor to the bottom left arrow and press
theFunctionSetupswitch.Movethecursoroverthelettertobeedited,movethe
cursortothelettertobeinsertedandthenpresstheFunctionSetupswitch.
Notes
❸ Press the Function Setup switch.
❹ Use the Function Setup switch to move
to a desired letter and select the letter
by pressing the switch. Repeat this to
enter multiple letters. You can enter up
to 15 letters.
SYNC :
In areas where the supply is at 60Hz, you can synchronize the output phase of
multiple cameras using the power synchronization function (Line-Lock) without
using a synchronization signal generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
FRONT DOOR
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
CLR POS END
CAM TITLE : If you enter a title, the title will appear on the monitor.

If the SPECIAL menu screen is displayed, use the Function Setup switch so that
the arrow indicates ‘CAM TITLE’.

Set it to ‘ON’ by using the Function Setup switch.
MOTION DET :
This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen,
and the words 'MOTION DETECTED' appear on the
screen when movement is detected. You can monitor
activity more efficient.
•BecausetheinputpowerofSIR-60isDC,SYNCisfixedatINT.
Notes

When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates 'MOTION DET'.

Set up the mode using the Function Setup switch.
- SENSITIVITY :You can select up to 8 MD areas. When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small
movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.

COLOR DOME CAMERA User’s Manual
26
COLOR DOME CAMERA User’s Manual
27
Operating Your Camera
•MDareasshowonlyMOTIONDETmenu.Therefore,MDareasdon’tdisplayonthe
monitor screen.
Notes
Press the Function Setup switch in the EXIT menu to save the current settings and exit the
MAIN SETUP menu.
EXIT
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.
LANGUAGE :
You can select the menu language according to your requirements.
IR MODE :
When IR LED is turned on in B/W, the objects can be
clearly identified due to the function that decreases
screen saturation of objects within a short distance.
- OFF : disabled Used to view clearly in dark
environments such as warehouse and outer
area.
- ON : IR MODE enabled
- TOP/DOWN/LEFT/RIGHT: Adjust the range according to the location of objects.


RESET :
Resets the camera settings to the factory defaults. Language is not initialized.
RETURN :
Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu.
- AREA SEL :You can select up to 8 PRIVACY areas.
- AREA MODE : Determines whether to use the area selected
in the AREA SEL, and the size and position
of the area.
- MASK COLOR :Determine area color. You can select Gray,
Black and White
-TRANSP : Determine the transparency of selected area as
controllingnumberfrom0to3.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
 PRIVACY :
Mask an area you want to hide on the screen,
  
When the SPECIAL menu screen is displayed, press
the Function Setup switch so that the arrow
indicates ‘PRIVACY’.
  
Set up the mode using the Function Setup switch.
•AstheDISfunctionusesthedigitalzoomthecamera'sresolutionwilldecrease.
•DISdoesn’toperatewhenbackgroundilluminationistoolow.
•DISdoesn’toperatewhenobjectpatternismonotonicaslikeskyorwhitewall.
•IfDISisenabled,thedigitalzoomisnotconfiguredtolessthan46level.
•IRMODEfunctiondoesnotworkinD&NCOLORmode.
Notes
Notes
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- FILL SET : Fills in a selected MD area. The color of filling is sequentially selected as brown,
orange, blue, cyan, yellowish green, yellow, magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.

COLOR DOME CAMERA User’s Manual
28
COLOR DOME CAMERA User’s Manual
29
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
●
Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera and monitor are fixed properly.
▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
● The image on the screen is dim.
▶ Is the lens stained with dirt? Clean your lens with a soft, clean cloth.
▶ Check the monitor and DVR settings.
▶ If the camera is exposed to very strong light, change the camera position.
● The image on the screen is dark.
▶ Adjust the contrast feature of the monitor or DVR.
▶ Ifyouhaveanintermediatedevice,setthe75Ω/Hi-zproperly.
● The camera is not working properly, and the surface of the camera is hot.
▶ Check that you have properly connected the camera to an appropriate power source.
● The DAY/NIGHT menu does not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
● The SENS-UP function does not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
● The Motion Detection function does not work.
▶ Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.
● Color is not correct.
▶ Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶ Check that the camera is not pointing at the sun.
● IR-LED isn't lighted.
▶ Isn't DAYNIGHT function setting up the color mode?
▶ Please change the AUTO or B/W mode.
Troubleshooting
Specifications
SIR-60N SIR-60P
ELECTRICAL
Input Voltage DC 12V
Power Consumption Max 2.5W
VIDEO
Imaging Device 1/3 inch, Diagonal 6mm Super HAD CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Scanning System 2 : 1 Interlace
Synchronization Internal
Frequency H:15.734KHz / V:59.94Hz H:15.625KHz / V:50.00Hz
Horizontal Resolution COLOR : 580TV line (Min.) / B/W : 700TV line (Min.)
Min. Illumination Color : 0.15Lux (50 IRE @F1.2)0.0003Lux (SENS-UP, x512)
B/W : 0Lux (IR LED ON)
S / N (Y signal) 52dB
Video Output CVBS : 1.0Vp-p / 75Ω
LENS
Focal Length Fixed 3.6mm (F2.0), IR LENS
Angular Field of View H : 73° x V : 53°
PAN / TILT / ROTATE
Pan / Tilt / Rotate Range 0° ~ 352° / 0° ~ 75°
OPERATIONAL
Electronic Shutter Speed ESC(NTSC:1/60) / Manual / A.FLK Fixed(PAL:1/50) / Manual / A.FLK
On Screen Display NTSC : Korean, English, Spanish, French, Japanese
PAL : English, French, German, Spanish, Italian, Chinese
Backlight Compensation BLC / HLC / Off
Day & Night Color / B&W / Auto (ICR)
Gain Control Low / High / Off
White Balance ATW / AWC / Manual / Indoor / Outdoor (1,700 °K ~ 11,000 °K)
SENS-UP (frame Integration) Auto / Off (Selectable limit x2 ~ x512)
Motion Detection On / Off (8 Programmable zones)
Privacy Masking On / Off (8 Programmable zones)
3D Noise Filter (SSNRII) On / Off (1 ~ 32 Level)
Digital Zoom On / Off (Level Adjustable)
Digital Image Stabilization (DIS) On / Off
Camera Title On / Off
Sharpness On / Off
Flip / Mirror On / Off
ENVIRONMENTAL
Operating Temperature / Humidity -10°C ~ +50°C / 30% ~ 80% RH
MECHANICAL
Dimension / Weight Ø107.6 x 83.7mm / 280g
※This specification can be changed without notice for performance improvement of product.

COLOR DOME CAMERA User’s Manual
30
COLOR DOME CAMERA User’s Manual
31
DECLARATION OF CONFORMITY
ApplicationofCouncilDirective(s) 89/336/EEC
Manufacturer'sName SAMSUNGTECHWINCO.,LTD
Manufacturer'sAddress SAMSUNGTECHWINCO.,LTD
 42,SUNGJU-DONGCHANGWON-CITY,
 KYUNGNAM,KOREA,641-716
EuropeanRepresentativeName
EuropeanRepresentativeAddress
EquipmentType/Environment CCTVCamera
ModelName SIR-60P
BeginningSerialNO. C11S3010007
YearofManufacture 2009.03.01
Conformanceto EN50081-1:1992
 EMC-Directive89/336EECand92/31/EEC
 EN50130-4:1996
We, the undersigned, hereby declare that the equipment specified above conforms
totheaboveDirective(s).
Manufacturer SAMSUNGTECHWINCO.,LTD LegalRepresentativeinEurope
Signature  Signature
FullName HANSEUGKIM FullName
Position QUALITYCONTROLMANAGER Position
Place CHANGWON,KOREA Place
Date 2009.03.01 Date
Ø107.6
R45
83.7mm
81.6mm
Dimension

P/No. : Z6806-0968-01B
VAN 09. 03
www.samsungtechwin.com
www.samsungcctv.com
•SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : [phone]~8 FAX : [phone]
•SAMSUNG TECHWIN EUROPE CO., LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : [phone] FAX : [phone]
•SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : [phone] FAX : [phone]
www.samsungcctvusa.com
SALES NETWORK