Samsung PS-42Q7HD User manual

PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
Register your product at www.samsung.com/global/register
This device is a Class B digital apparatus.
ON-SCREEN MENUS
Picture InPicture (PIP)
Energy Saving
TELETEXT (Option)
SRS TruSurroundXT
Digital Natural Image engine

English - 2
◆Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma
monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known
as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when
displaying a still image.
◆Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in
height so do not install and operate there.
◆Heat on the top of the PDP TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent
hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the
product. However, children should be prevented from touching the upper part of the product.
◆The product is making a ‘cracking’ noise.
A‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment
such as temperature or humidity. This is normal and not a defect of the unit.
◆Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated
technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
◆Avoid operating the TV at temperatures below 5°C(41°F)
◆Astill image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders
displayed on the left, right and centre of the screen caused by the difference of light
emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damages caused by the above effect are not covered by the Warranty.
◆Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial
after images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
◆Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
◆Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low
temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train
station etc. Failure to do so may cause a serious damage to your set.
User Instructions
Checking Parts
Sold Separately
Owner’s
Instructions
Remote Control/
AAA Batteries
Power Cord Ferrite Core for Antenna
Cable and Power Cord
S-VIDEO Cable
PC Cable
HDMI Cable
PC Audio Cable HDMI/DVI Cable
Component Cables
(RCA)
Antenna Cable
➢Ferrite Core (Power Cord, Antenna Cable)
The ferrite core is used to shield the cable from
interference. When connecting a cable,open
the ferrite core and clip it around the cable.

English - 3
Contents
◆GENERAL INFORMATION
■User Instructions ................................................................................................... 2
■Checking Parts...................................................................................................... 2
■Control Panel ........................................................................................................ 5
■Connection Panel.................................................................................................. 5
■Viewing the Remote Control (depending on the model)....................................... 7
■Installing Batteries in the Remote Control ............................................................ 8
◆OPERATION
■Switching Your Television On and Off................................................................... 8
■Viewing the Menus................................................................................................ 9
■Freezing the Current Picture................................................................................. 9
■Plug & Play Feature .............................................................................................. 10
■Viewing an External Signal Source....................................................................... 12
■Editing Device Names........................................................................................... 12
◆CHANNEL CONTROL
■Storing Channels Automatically ............................................................................ 13
■Storing Channels Manually ................................................................................... 14
■Adding / Locking Channels ................................................................................... 15
■Sorting the Stored Channels................................................................................. 16
■Assigning Names to Channels.............................................................................. 16
■Fine Tuning Channel Reception............................................................................ 17
◆PICTURE CONTROL
■Changing the Picture Standard............................................................................. 18
■Customizing the Picture Settings .......................................................................... 18
■Selecting the Picture Size ..................................................................................... 19
■Digital NR .............................................................................................................. 20
■SMD ...................................................................................................................... 20
■DNIe Demo ........................................................................................................... 20
■Viewing the Picture in Picture (PIP)...................................................................... 21
◆SOUND CONTROL
■Sound Features..................................................................................................... 22
◆FUNCTION DESCRIPTION
■Time Features ....................................................................................................... 23
■Language .............................................................................................................. 24
■Blue Screen........................................................................................................... 24
■Melody................................................................................................................... 24
■Energy Saving....................................................................................................... 24
■Using Game Mode ................................................................................................ 24
■Screen Burn Protection......................................................................................... 25
■Setting the Blue Eye ............................................................................................. 26
◆PC DISPLAY
■Setting up Your PC Software (Based on Windows XP)........................................ 26
■Input Mode (PC).................................................................................................... 27
■Setting the PC....................................................................................................... 28

English - 4
☛➢
Press Important Note
Symbols
◆USING THE DTV FEATURE
■Previewing the DTV Menu System ....................................................................... 29
■Updating the Channel Manager Automatically...................................................... 30
■Updating the Channel Manager Manually............................................................. 31
■Editing Your Favourite Channels........................................................................... 32
■Select Channel Manager....................................................................................... 35
■Viewing Channel Lists........................................................................................... 35
■Displaying Programme Information....................................................................... 36
■Viewing the EPG (Electronic Programme Guide) Information.............................. 37
■Using the Scheduled List ...................................................................................... 39
■Setting the Default Guide...................................................................................... 40
■Viewing All Channels and Favourite Channels ..................................................... 41
■Adjusting the Translucency Level ......................................................................... 42
■Setting up the Parental Lock................................................................................. 43
■Setting the Subtitle................................................................................................ 44
■Selecting the Preferred Language (Subtitle or Audio) .......................................... 45
■Selecting the Audio Format................................................................................... 46
■Selecting the Time Zone ....................................................................................... 47
■Viewing Product Information ................................................................................. 48
■Checking the Signal Information ........................................................................... 48
■Upgrading the Software (Option) .......................................................................... 49
■Resetting ............................................................................................................... 50
◆USING THE TELETEXT FEATURE
■Teletext Feature (depending on the model) .......................................................... 51
◆APPENDIX
■How to Install the Wall Mount Bracket .................................................................. 53
■Troubleshooting..................................................................................................... 55
Contents

English - 5
➢The product colour and shape may vary depending on the model.
Control Panel
Front (or Side) Panel
ΠSOURCE
Displays a menu of all of the available input sources
(TV, AV1, AV2, S-Video, Component1, Component2,
PC, HDMI, DTV).
´ MENU
Press to see the on-screen menu of your TV’s
features.
ˇ VOL
+
,
-
Press to increase or decrease the volume.
In the on-screen menu, use the VOL
+
,
-
buttons as
you use the œand √buttons on the remote control.
¨ CH ,
Press to change channels. In the on-screen menu,
use the CH ,buttons as you use the …and †
buttons on the remote control.
ˆ (ENTER)
Press to confirm a selection.
Ø (Power) button
Press to turn the TV on and off.
Power Indicator
- Power Off: Blue
- Power On: Off
Remote Control Sensor
Aim the remote control towards this spot on the TV.
Speaker
➢The product colour and shape may vary depending on the model.
Connection Panel
Side Panel
or
continued...
ŒS-Video or Video / Audio L/R
- Video (S-Video or Video) and
audio inputs for external devices,
such as a camcorder or VCR.
´headphones jack
- You can connect a set of
headphones to your television if
you wish to watch a television
programme without disturbing the
other people in the room.
➢
Prolonged use of headphones
at a high volume may damage
your hearing.
Œ
´

- When connecting this product via HDMI or DVI to a
Set Top Box, DVD Player or Games Console etc,
make sure that it has been set to a compatible video
output mode as shown in the table below. Failure to
observe this may result in picture distortion, image
breakup or no picture.
- Do not attempt to connect the HDMI/DVI connector to a
PC or Laptop Graphics Card.
(This will result in a blank screen being displayed)
DVI AUDIO IN L/R
- DVI audio outputs for external devices.
POWER IN
-Connect the supplied power cord.
SERVICE
- Connector for service only.
DIGTAL AUDIO OUT (OPTICAL)
Connect optical digital audio cable to "DIGITAL AUDIO OUT" on
the rear of your set and the other end to "DIGITAL IN" of the
equipment with a digital input to enjoy digital sound.
➢ Supported modes for HDMI/DVI and Component
English - 6
➢The product colour and shape may vary depending on the model.
Connection Panel
ANT IN VHF/UHF (75Ω)
- 75ΩCoaxial connector for Aerial/Cable Network.
Connecting external Audio Devices
- Connect RCA audio signals from the TV to an external
source, such as Audio equipment.
PC IN / AUDIO
- Connect to the video and audio output jack on your PC.
Connecting External A/V Devices
- Connect RCA cable to an appropriate external A/V
device such as VCR, DVD or Camcorder.
- Connect RCA audio cables to “R - AUDIO - L” on the
rear of your set and the other ends to corresponding
audio out connectors on the A/V device.
COMPONENT IN 1, COMPONENT IN 2
- Video (Y/PB/PR) and audio (AUDIO L/R) inputs for
Component.
HDMI/DVI IN
- Connect to the HDMI jack of a device with HDMI output.
These inputs can also be used as a DVI connection
with separate analog audio inputs. An optional
HDMI/DVI cable will be necessary to make this
connection. When using the optional HDMI/DVI adapter,
the DVI analog audio inputs on your TV allow you to
receive left and right audio from your DVI device.
(Not compatible with PC)
☛
Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
☛
When connecting an external device, match the colour of the connection terminal to the cable.
Rear Panel
Cable Television
Network
or
or
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
480i
X
X
O
480p
X
O
X
576i
X
X
O
576p
O
X
O
720p
O
O
O
1080i
O
O
O
TruSurround XT, SRS and
symbolare trademarks
of SRS Labs, Inc.

English - 7
➢The performance of the remote control may be affected by bright light.
➢This is a special remote control for the visually impaired, and has Braille points on the Power, Channel and
Volume buttons.
Viewing the Remote Control (depending on the model)
Select the TV mode directly
POWER button
(turns the TV on and off)
Number buttons for direct
channel access
One/Two-digit channel
selection
Channel control button
(Refer to page 15)
Interchange the TV and DTV
mode
VCR/DVD functions
- REWIND (REW)
- STOP
- PLAY/PAUSE
- FAST FORWARD (FF)
Volume increase
Volume decrease
Temporary sound switch-off
Displays the main on-screen
menu
Control the cursor in the menu
Use to see information on the
current broadcast
Electronic program guide (EPG)
display
Picture effect selection
(Refer to page 18)
Picture-In-Picture On/Off
Picture freeze
Sound mode selection
Make the remote control work
for STB, VCR, CABLE or DVD
Available source selection
Previous channel
DTV menu display
Automatic Power-off
Next channel
Previous channel
Exit the on-screen menu
Sound effect selection
(Refer to page 21)
Picture size selection
Digital subtitle display
TruSurround XT mode button
Remote control setup
If your remote control is not
functioning properly, take out
the batteries and press the reset
button for about 2~3 seconds.
Re-insert the batteries and try
using the remote control again.
Teletext Functions (Refer to page 51)
Exit from the teletext display
(depending on the model)
Teletext index
Teletext reveal
Teletext size selection
Teletext hold
Teletext mode selection
(LIST/FLOF)
Teletext sub page
P:Teletext next page
P:Teletext previous page
Teletext cancel
Teletext display/mix both
teletext information and
the normal broadcast
Teletext store
Fastext topic selection

1Lift the cover at the back of the remote control upward as shown in the figure.
2Install two AAA size batteries.
➢ Make sure to match the “+” and “–” ends of the batteries with the diagram
inside the compartment.
3Close the cover as shown in the figure.
➢ Remove the batteries and store them in a cool, dry place if you won’t be using
the remote control for a long time.
➢If the remote control doesn’t work! Check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
English - 8
Installing Batteries in the Remote Control
The mains lead is attached to the rear of the television.
1Plug the mains lead into an appropriate socket.
➢The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2Press the (Power) button (On/Off) on the front of the television or press the POWER ()button on the remote
control to switch the television on. The programme that you were watching last is re-selected automatically.
If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically”
on page 13 or “Storing Channels Manually” on page 14.
➢If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 10.
3To switch the television off, press the (Power) button (On/Off) on the front of the television or press the
POWER ()button on the remote control.
4To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER ()button
or number buttons on the remote control.
Switching Your Television On and Off

English - 9
Viewing the Menus
1Press the MENU ()button.
The main menu is displayed on the screen.
Its left side has five icons: Input, Picture, Sound, Channel, and Setup.
2Press the …or †button to select one of the icons.
Press the ENTER
() button to access the icon’s sub-menu.
3Press the …or †button to move to items in the menu.
Press the ENTER
() button to enter items in the menu.
4Press the …/†/œ/√button to change the selected items.
Press the MENU ()button to return to the previous menu.
5Press the EXIT button to exit from the menu.
Freezing the Current Picture
You can freeze the picture when watching a television programme simply by
pressing the “STILL” button. To return to normal viewing, press it again.
➢This function will automatically cancel five minutes later.
Input
Move Enter Exit
Source List : TV
Edit Name
TV

Clock Set 12 :00
Plug & Play
Move Adjust Enter Skip
English - 10
Plug & Play Feature
1If the television is in standby mode, press the POWER ()button
on the remote control. The message to start Plug & Play is displayed.
2Make sure that the antenna is connected to the TV.
Press the
ENTER () button. The menu to select channels is displayed
3To start channel store, press the
ENTER () button.
The search will end automatically. The TV will begin memorizing all of the
available channels.
Press the
ENTER () button to set the clock.
4Press the œor √button to select the hour or minute.
Set these by pressing the
…or † button.
➢ You can enter the hours or minutes by using the numeric buttons on the
remote control.
When the television is initially powered on, several basic customer settings proceed automatically and subsequently.
The following settings are available.
Check antenna input.
OK
Plug & Play
Enter Skip
Clock Set -- : --
Plug & Play
Enter Skip
Start Plug & Play.
OK
Plug & Play
Enter Exit
Enter Skip
Plug & Play
Auto Store
P1 C
--
40 MHz
0%
Start
Enter Skip
Plug & Play
Auto Store
P1 C
--
40 MHz
0%
Stop

English - 11
Setup
Move Enter Return
Plug & Play
Language : English
Time
Game Mode : Off
Blue Screen : Off
Melody : Off
PC
More
TV
Plug & Play
The channel list is being updated.
To abort the scan press D.MENU.
Stop
Skip
Scanning for digital services...
739%
Services found:0 Channel:9A
5Plug and Play for TV complete, and Plug and Play for DTV will start
automatically.
The search will end automatically. Channels are sorted and stored in the
order which reflects their position in the frequency range (with lowest first
and highest last). When this has finished, the menu to set the Time Zone will
be displayed.
➢To stop DTV channel the search before it has finished or return to
normal viewing, press the D.MENU
or the ENTER () button.
6Select the time zone where you locate by pressing the
…or † button.
Press the ENTER
() button.
The following options are available.
New South Wales/ACT - Victoria - Queensland - South
Australia - Western Australia - Tasmania - Northern
Territory
7Press the
ENTER () button to confirm your setting.
The message “Enjoy your watching” is displayed.
If you want to reset this feature …
1Press the MENU ()button to display the menu. (On TV mode)
2
Press the …or †button to select Setup, then press the ENTER ()
button.
3Press the ENTER () button again to select Plug & Play.
The message to start Plug & Play is displayed.
Plug & Play
Selects the time zone where you locate
New South Wales/ACT
Victoria
Queensland
South Australia
Western Australia
Tasmania
Northern Territory
Move Select Skip
Plug & Play
Selects the time zone where you locate
New South Wales/ACT
Victoria
Queensland
South Australia
Western Australia
Tasmania
Northern Territory
Move Select Skip
Enjoy your watching
OK
Plug & Play
Exit

English - 12
1Press the MENU ()button to display the menu.
2
Press the ENTER ()button to select Source List.
3Press the ENTER () button again.
4Press the
…or † button to select the signal source, then press the
ENTER () button.
Available signal source: TV, AV1, AV2, S-Video, Component1,
Component2, PC, HDMI, DTV
➢You can select these options simply by pressing the SOURCE button
on the remote control. (Only for External Signal Source)
Viewing an External Signal Source
You can switch between viewing signal from connected equipment, such as a VCR, DVD, Set-Top Box, and the TV
source (broadcast or cable).
1Press the MENU ()button to display the menu.
2
Press the ENTER ()button.
3Press the …or †button to select Edit Name, then press theENTER ()
button.
4Press the
…or † button to select the external source to be edited, then
press the
ENTER () button.
5Select the required device by pressing
…or † , then press the ENTER ()
button.
Available device names: VCR, DVD, D-VHS, Cable STB, HD STB,
Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder,
DVD Combo, DHR (DVD HDD Recorder), or PC.
6Press the EXIT button to exit.
Editing Device Names
Input
Move Enter Return
Source List : TV
Edit Name
TV
Input
Move Enter Return
Source List : TV
Edit Name
TV
Source List
Move Enter Return
TV
AV1 :
----
AV2 : ----
S-Video : ----
Component1 : ----
Component2 : ----
PC : ----
HDMI : ----
DTV
TV
Edit Name
Move Enter Return
AV1 : ----
AV2 : ----
S-Video :
----
Component1 : ----
Component2 : ----
PC : ----
HDMI : ----
TV
----
VCR
DVD
D-VHS
Cable STB
You can give a name to the external source.

English - 13
Storing Channels Automatically
You can scan for the frequency ranges available to you (availability depends on your Country).
Automatically allocated programme numbers may not correspond to actual or desired programme numbers.
However you can sort numbers manually and clear any channels you do not wish to watch.
Channel
Move Enter Return
Country : Australia
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
Enter Return
Auto Store
P1 C
--
40 MHz
0%
Start
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Channel , then press the ENTER ()
button.
3 Press the …or †button to select Auto Store, then press the ENTER ()
button.
4 Press the ENTER ()button again to start the search.
The search will end automatically.
➢ To stop the search before it has finished, press the MENU ()or the
ENTER () button.
➢ The Australia is the default in the Country cases depending on the
model.

English - 14
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Channel, then press the ENTER ()
button.
3Press the …or † button to select Manual Store, then press the ENTER ()
button.
4Select the required option by pressing the
…or † button, then press the
ENTER () button.
5When you are satisfied with your setting, press the
ENTER () button.
6Press the EXIT button to exit.
◆Programme (Programme number to be assigned to a channel)
- Press the …or † button until you find the correct number.
◆Colour System:AUTO/PAL/SECAM/NTSC4.43
- Press the …or † button to select the required colour standard.
◆Sound System:BG/DK/I
- Press the …or † button to select the required sound standard.
◆Channel (When you know the number of the channel to be stored)
- Press the …or † button to select C(Air channel) or S(Cable channel).
- Press the √button, then press the …or † button to select the required number.
➢ You can also select the channel number directly by pressing the numeric buttons (0~9).
➢ If there is abnormal sound or no sound, re-select the sound standard required.
◆Search (When you do not know the channel numbers)
- Press the …or † button to start the search.
- The tuner scans the frequency range until the first channel or the channel that you selected is received
on the screen.
◆Store (When you store the channel and associated programme number)
- Set to OK by pressing the ENTER () button.
☛Channel mode
◆P(Programme mode): When completing tuning, the broadcasting stations in your area have been assigned
to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.
◆C(Air channel mode): You can select a channel by entering the assigned number to each air broadcasting
station in this mode.
◆S(Cable channel mode): You can select a channel by entering the assigned number for each cable channel
in this mode.
You can store television channels, including those received via cable networks.
When storing channels manually, you can choose:
◆Whether or not to store each of the channels found.
◆The programme number of each stored channel which you wish to identify.
Storing Channels Manually
Channel
Move Enter Return
Country : Australia
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
Manual Store
Move Enter Return
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 2
Search : 48 MHz
Store : ?
TV

English - 15
Using the Channel Manager, you can conveniently lock or add channels.
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Channel, then press the ENTER ()button.
3Press the …or † button to select Channel Manager, then press the
ENTER () button.
◆Adding channels
Using the Channel Manager, you can add channels.
4Select the Channel Manager by pressing the ENTER () button.
5Move to the
() field by pressing the …/†/ œ / √buttons, select a channel to
be added, and press the
ENTER () button to add the channel.
➢If you press the
ENTER () button again, the
() symbol next to the
channel disappears and the channel is not added.
◆Locking channels
This feature allows you to prevent unauthorized users, such as children, from
watching unsuitable programmes by muting out video and audio.
6Press the …or † button to select Child Lock, then press the ENTER ()
button.
7Select On by pressing the
…or † buttons, then press the ENTER ()
button.
8Press the
…or † buttons to select the Channel Manager, then press the
ENTER () button.
9Move to the
() field by pressing the …/†/ œ / √buttons, select a channel to
be locked, and press the
ENTER ()
button.
➢If you press the
ENTER () button again, the () symbol next to the
channel disappears and the channel lock is canceled.
➢Ablue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
➢You can select these options simply by pressing the CH MGR button
on the remote control.
Adding / Locking Channels
Channel
Move Enter Return
Country : Australia
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
Channel Manager
Move Enter Return
Channel Manager
Child Lock : Off
TV
Move Enter
Page Return
Add Lock
Channel Manager
P1 C 16 BBC 1 1 / 10
Prog.
0C --
1BBC 1
2C3
3S1
4S3
5S6
6S7
7S9
8S11
9S12
Channel Manager
Move Enter Return
Channel Manager
Child Lock : On
TV

English - 16
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Channel, then press the ENTER ()button.
3 Press the …or †button to select Sort, then press the ENTER ()button.
4Select the channel that you wish to move by pressing the …or † button,
then press the
ENTER () button.
5Select the number of the programme to which the channel is to be moved
by pressing the
…or † button.
Press the
ENTER () button. The channel is moved to its new position and
all other channels are shifted accordingly.
6Repeat steps 4to 5until you have moved all the channels to the required
programme numbers.
7Press the EXIT button to exit.
Sorting the Stored Channels
Channel names will be assigned automatically when channel information is
broadcast. These names can be changed, allowing you to assign new names.
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Channel, then press the ENTER ()button.
3 Press the …or †button to select Name, then press the ENTER ()
button.
4 Press the …or †button to select the channel to be assigned to a new name,
then press the ENTER ()button.
5 Press the …or †button to select a letter (A~Z), a number (0~9), or a symbol.
Move on to the previous or next letter by pressing the
œor √ button , then
press the ENTER ()button.
6Repeat steps 4to 5for each channel to be assigned to a new name.
7Press the EXIT button to exit.
Assigning Names to Channels
Channel
Move Enter Return
Country : Australia
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
Sort
Move Enter Return
TV
Prog. Ch. Name
0C
--
1C2
2C83
3C80
4C7
Name
Move Adjust Return
TV
Channel
Move Enter Return
Country : Australia
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
0C -- -----
1C2
-----
2C83 -----
3C80 -----
4C7 -----
A
This operation allows you to change the programme numbers of stored channels.
This operation may be necessary after using auto store.
Channel names will be assigned automatically when channel information is broadcast.
These names can be changed, allowing you to assign new names.
Prog. Ch. Name

English - 17
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Channel, then press the ENTER ()
button.
3Press the …or † button to select Fine Tune, then press the ENTER ()
button.
4To obtain a sharp and clear picture and good sound quality, press the œor √
button until you reach the optimal setting.
Press the ENTER () button.
➢To reset the fine tuning to 0, select Reset by pressing the
…or †
button. Press the ENTER () button.
5Press the EXIT button to exit.
➢Fine Tune Store will change the colour of the Channel OSD (On Screen
Display) from White to Red and add the “*” mark.
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and
store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.
Channel
Move Enter Return
Country : Australia
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
P1
*
Mono
P1
*
+3
Reset
Fine Tune
Adjust Save Return

English - 18
You can select the type of picture which best corresponds to your viewing requirements.
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Picture, then press the ENTER ()
button.
3Press the ENTER ()button twice.
4Select the required mode by pressing the …or †button, then press the
ENTER ()button.
Available modes: Dynamic, Standard, Movie, Custom
➢ The settings values may vary depending on the input source.
(ex. RF, Video, Component, PC, or HDMI)
5Press the EXIT button to exit.
➢You can select these options simply by pressing the P.MODE button
on the remote control.
➢◆ Choose Dynamic for viewing the TV during the day or when there is
bright light in the room.
◆ Choose Standard for the standard factory settings.
◆ Choose Movie when viewing the movie.
◆ Choose Custom if you want to adjust the settings according to personal
preference.
Changing the Picture Standard
Your television has several setting options that allow you to control the picture quality.
◆Contrast – Brightness – Sharpness – Colour – Tint (NTSC only)
◆Contrast – Brightness – Colour : PC Mode
Press the œor √button until you reach the optimal setting.
◆Colour Tone: Cool 2/Cool 1/Normal/Warm 1/Warm 2
◆Reset: You can return to the factory defaults picture settings.
➢The reset function is set for each picture mode and colour tone.
1Press the MENU ()button to display the menu.
2
Press the …or †button to select Picture, then press the ENTER ()
button.
3Press the ENTER ()button twice.
4Select the required mode by pressing the …or †button, then press the
ENTER ()button.
Available modes: Dynamic, Standard, Movie, Custom
5Select the required option by pressing the …or †button, then press the
ENTER ()button.
6When you are satisfied with your setting, press the ENTER ()button.
7Press the EXIT button to exit.
Customizing the Picture Settings
Picture
Move Enter Return
Mode : Dynamic
Size : 16:9
Digital NR : On
SMD : On
DNIe Demo : Off
PIP
TV
Picture
Move Enter Return
Mode : Dynamic
Size : 16:9
Digital NR : On
SMD : On
DNIe Demo : Off
PIP
TV
Mode
Move Enter Return
Mode : Dynamic
Contrast 100
Brightness 50
Sharpness 75
Colour 55
Tint G 50 R 50
Colour Tone : Cool 1
Reset
TV
Dynamic
Standard
Movie
Custom
Mode
Move Enter Return
Mode : Dynamic
Contrast 100
Brightness 50
Sharpness 75
Colour 55
Tint G 50 R 50
Colour Tone : Cool1
Reset
TV
Cool 2
Cool 1
Normal
Warm 1
Warm 2

English - 19
Selecting the Picture Size
You can select the picture size which best corresponds to your viewing
requirements.
1Press the MENU ()button to display the menu.
2Press the …or †button to select Picture, then press the ENTER ()
button.
3Press the …or †button to select Size, then press the ENTER ()button.
4Select the required option by pressing the …or †button, then press the
ENTER ()button.
Available options: 16:9, Wide 4:3, Zoom, 4:3
◆ 16:9
: Sets the picture to 16:9 wide mode.
◆ Wide 4:3
: Magnify the size of the picture more than 4:3 .
Move the screen up/down using the …or †button after
selecting the by pressing the √or ENTER ()button.
◆ Zoom
: Magnify the size of the picture vertically on screen.
◆ 4:3
: Sets the picture to 4:3 normal mode.
5Press the EXIT button to exit.
➢ You can change the picture size simply by pressing the P.SIZE button
on the remote control.
➢ If you change the picture size when PIP is On, PIP will automatically
be turned Off.
➢ Depending on the input source, the picture size options may vary.
➢ The items available may differ depending on the selected mode.
Positioning and Sizing the screen using Zoom
◆Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction
using the …or †button as well as the screen size.
◆Move the screen up/down using the …or †button after selecting the by pressing the œor √button.
◆Resize the screen vertically using the …or †button after selecting the by pressing the œor √button.
Picture
Move Enter Return
Mode : Dynamic
Size : 16:9
Digital NR : On
SMD : On
DNIe Demo : Off
PIP
TV
Size
Move Enter Return
16:9
Wide 4:3
Zoom
4:3
TV

English - 20
1Press the MENU ()button to display the menu.
2Press the …or †button to select Picture, then press the ENTER ()
button.
3Select the required option by pressing the
…or † button, then press the
ENTER () button.
Available options: Digital NR, SMD, DNIe Demo
4When you are satisfied with your setting, press the ENTER ()button.
5Press the EXIT button to exit.
◆Digital NR
: On/Off
If the signal received by the television is weak, you can activate this feature to
reduce any static and ghosting
that may appear on the screen.
◆SMD(Smooth Motion Driver): On/Off
If you set SMD to On, you can view more natural skin and clear text even in
fast moving scenes.
(SMD is applicable only to PAL and SECAM system.)
➢SMD is not available in PC mode.
◆DNIe Demo
: On/Off
This TV includes the DNIe function so as to provide a high visual quality.
If you set DNIe Demo to On, you can view an applied DNIe and a normal pic-
ture on the screen, for demonstration purposes. Using this function, you can
view the difference in the visual quality.
➢DNIe
TM
(Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction,
detail enhancement, contrast enhancement and white enhancement.
New image compensation Algorithm gives brighter, clearer, more
detailed image to you. DNIe
TM
technology will fit every signal into your
eyes.
➢ DNIe Demo is not available in PC mode.
Digital NR / SMD / DNIe Demo
Picture
Move Enter Return
Mode : Dynamic
Size : 16:9
Digital NR : On
SMD : On
DNIe Demo : Off
PIP
TV