S&T Kontron 3.5"-SBC-TGL User manual

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 1

3.5"
-SBC-TGL- QUICK INSTALLATION GUIDE
Thank you for purchasing the Kontron 3.5"-SBC-TGL embedded board. This document provides information to allow you
to quickly install this product.
Packing Checklist
1. Take the 3.5"-SBC-TGL out of the packing box and check if the unit is properly secure in the plastic bag.
2. Check the contents of the carton box: (*: optional)
3.5"-SBC-TGL main board
Quick Installation Guide
DC IN Cable
COM Port Cable *
DIO Cable *
USB Cable (2 Port) *
SATA Cable *
SATA Power Cable *
Audio Cable *
Speaker with Cable *
Panel LVDS Cable *
Panel Backlight Cable *
Cooler *
Extended I/O Board *

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 2
Top Side Jumper and Internal Connector Locations
Jumper List
Item Designation Description
1 JP1 LVDS Backlight Control Selection
2 JP2 M.2 Key B Selection
3 JP3 LVDS Panel Power Selection
4 JP4 LVDS Backlight Enable Selection
5 JP5 LVDS Backlight Enable Voltage Selection
6 JP6 Flash Descriptor Security Override Selection
7 JP7 AT / ATX Power Mode Selection
8 JP8 Clear CMOS Selection
9 JP9 MFG Mode Selection
10 JP10 USB Power Selection
15
1
2
30
14
3
5
4
6
7
8
22
9
10
11
12
13
16
17
18
19
20
21
23
24
25
26
27
28
29
31
32
33

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 3
Internal Connector List
Item Designation Description
11 CN1 Left Channel Audio AMP Output Wafer
12 CN2 LVDS Backlight Power Wafer
13 CN3 DIO Header
14 CN4 Fan Wafer
15 CN5 Right Channel Audio AMP Output Wafer
16 CN6 Micro SIM Card Holder for M2B1
17 CN7 Audio Input / Output Header
18 CN8 Activity Indicator Header for M2B1
19 CN9 SATA Power Output Wafer
20 CN11 Activity Indicator Header for M2E1
21 CN12 +12 V DC Power Input Wafer
22 CN14 Activity Indicator Header for M2M1
23 CN19 USB 2.0 Port 5, 6 Header
24 CN20 USB 2.0 Port 7, 8 Header
25 CN26 RTC Power Input Wafer
26 CN27 SATA Port 0 Connector
27 CN28 Extended B2B Connector
28 DIMM1 DDR4 Channel 0 SO-DIMM Slot
29 DIMM2 DDR4 Channel 1 SO-DIMM Slot
30 FP1 Front Panel Header 1
31 FP2 Front Panel Header 2
32 M2B1 M.2 Key B 2242 / 3042 / 2280 Slot
33 M2E1 M.2 Key E 2230 Slot
Jumper Setting
LVDS Backlight Control Selection (JP1)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - PWM Control Mode
- X Voltage Control Mode
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
2
3
1

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 4
LVDS Backlight Control Selection (JP2)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - PCIe x1
- X SATA (Default)
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
LVDS Panel Power Selection (JP3)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - Backlight Power = +12 V
- X Backlight Power = +5 V
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - Panel Power = +3.3 V
- X Panel Power = +5 V
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
LVDS Backlight Enable Selection (JP4)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - High Active
- X Low Active
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
2
3
1
21
65
2
3
1

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 5
LVDS Backlight Enable Voltage Selection (JP5)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - +3.3 V
- X +5 V
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
Flash Descriptor Security Override Selection (JP6)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation
- X Flash Security Override
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
AT / ATX Power Mode Selection (JP7)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - ATX Power Mode
- X AT Power Mode
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
2
3
1
2
3
1
2
3
1

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 6
Clear CMOS Selection (JP8)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation (default position)
- X Clear CMOS (board does not boot with the jumper in this position)
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
MFG Mode Selection (JP9)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation
- X Enable MFG Mode
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
USB Power Selection (JP10)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - +5 V
- X +5 VSB
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
2
3
1
2
3
1
2
3
1

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 7
Bottom Side Internal Connector Locations
Item Designation Description
1 CN23 RS232/422/485 COM2 Wafer
2 CN24 RS232/422/485 COM1 Wafer
3 CN25 24-bit / 2-ch LVDS Connector
4 M2M1 M.2 Key M 2280 Slot
3
1
2
4

Kontron 3.5"-SBC-TGL - Quick Installation Guide - Version 1 - P/N: 0D2035STGL010000 // 8
Rear I/O Panel Connector Locations
Item Designation Description
1 CN15 2.5GbE LAN1 RJ45 Connector
2 CN16 GbE LAN2 RJ45 Connector
3 CN17 USB 3.2 Gen 2 Port 3, 4 Type A Connector
4 CN18 USB 3.2 Gen 2 Port 1, 2 Type A Connector
5 CN21 DP Port 1 Connector
6 CN22 DP Port 2 Connector
7 SW1 Power Button
8 LED1 Power LED
9 LED2 Standby LED
3
4
5
6
1
8
2
9
7