Advantech PCM-5862E User manual

PCM-5862E/EL
All in one multi-media Pentium
processor-based single board
computer with audio, SVGA,
Ethernet and PCI expansion slot.
User's Manual for PCM-5862E/EL

Copyright Notice
This document is copyrighted, 1997. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result
from its use.
Acknowledgments
AMD is a trademark of Advanced Micro Devices, Inc.
Award is a trademark of Award Software International, Inc.
C&T is a trademark of Chips and Technologies, Inc.
Cyrix is a trademark of Cyrix Corporation.
IBM, PC/AT, PS/2 and VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows ®is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
SiS is a trademark of Silicon Integration Systems Corporation
UMC is a trademark of United Microelectronics Corporation.
IDT is a trademark of Intergrated Device Technology , Inc.
All other product names or trademarks are properties of their
respective owners.
For more information on this and other Advantech products please
visit our website at: http://www.advantech.com
http://www.advantech.com/epc
For technical support and service for please visit our support
website at: http://support.advantech.com
This manual is for the PCM-5862E/EL Rev. A102-1 or higher
Part No. 2006586202 2nd Edition
Printed in Taiwan Jan. 1999

Packing list
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 1 PCM-5862E/5862EL All-in-One Single Board Computer
• 2 Ethernet driver disk
• 2 utility disks with PCI SVGA utility programs and drivers
for Windows 3.1, Windows 95, Windows NT 4.0, and OS/2
• 1 audio driver disks for Windows 3.1, Windows 95, and
DOS utility program. (PCM-5862E only)
If any of these items are missing or damaged, contact your distribu-
tor or sales representative immediately.
Please refer to page 98 for the optional interface wiring kit.

Contents
Chapter 1 General Information .....................1
Introduction .............................................................................................. 2
Highly integrated multi-media SBC................................................ 2
Features ..................................................................................................... 3
Specifications ............................................................................................ 3
Standard SBC functions .................................................................. 3
PCI SVGA/flat panel interface: ...................................................... 4
Audio function: (PCM-5862E only) ............................................... 4
PCI Bus Ethernet Interface: ............................................................ 5
Mechanical and environmental ....................................................... 5
Board layout and dimensions .................................................................. 5
Chapter 2 Installation.....................................7
Jumpers ..................................................................................................... 8
Connectors ................................................................................................ 9
Locatingjumpers.................................................................................... 10
Locatingconnectors ................................................................................11
Settingjumpers....................................................................................... 12
CPU installation and upgrading............................................................ 13
Install a CPU in the ZIF socket..................................................... 13
System clock setting (J1, J2, and J4) ............................................ 14
System/PCI clock setting .............................................................. 15
CPU frequency ratio...................................................................... 15
Pentium MMX(P55C) enabled/disabled (JP2) ............................. 15
CPU voltage setting (JP1) ............................................................. 16
M1 cache linear mode setting (J5) ................................................ 16
CMOS clear (J6) ........................................................................... 17
Buzzer enabled/disabled (J7) ........................................................ 17
Installing DRAM (SIMMs) ................................................................... 17
Installing SIMMs .......................................................................... 17
IDE hard drive connector (CN17) ........................................................ 18
Connecting the hard drive ............................................................. 18
Floppy drive connector (CN18)............................................................. 19
Connecting the floppy drive.......................................................... 19
Parallel port connector (CN19) ............................................................. 20
Keyboard and PS/2 mouse connector (CN15)...................................... 20

Front panel connector (CN7)................................................................. 20
Speaker ......................................................................................... 21
LED interface ............................................................................... 21
Watchdog output........................................................................... 21
Reset switch .................................................................................. 21
Power connectors (CN6, CN10, CN14) ................................................ 21
Peripheral power connector, -5V, -12V (CN10) ........................... 21
Main power connector, +5V, +12V (CN14) ................................. 21
Fan power supply connector (CN6) .............................................. 21
ATX Power Control Connector (CON1, CON2) ................................. 22
ATX feature connector (CON1) and
soft power switch connector (CON2) ........................................... 22
Wiring for ATX soft power switch function ........................................ 22
ATW Power enable/disable setting(J17)............................................... 23
IR connector (CN12) .............................................................................. 23
Audio interfaces (CN8, CN13) .............................................................. 23
Audio connector (CN13)............................................................... 23
CD audio input connector (CN8).................................................. 23
Audio power source setting (J16) ................................................. 23
Audio power source setting........................................................... 24
COM-port connector (CN16) ................................................................ 25
COM2 RS-232/422/485 setting (J14, J15) ................................... 25
COM3/COM4 RI pin setting (J11, J12)........................................ 26
VGA interface connections .................................................................... 27
CRT display connector (CN1)....................................................... 27
Flat panel display connector (CN2) .............................................. 27
LCD power setting (J10)............................................................... 28
LCD power setting ................................................................................... 28
Ethernet configuration ........................................................................... 29
100BASE-T connector (CN11)..................................................... 29
Network boot................................................................................. 29
Watchdog timerconfiguration .............................................................. 30
Watchdog timer action (J13) ......................................................... 30
USB connectors (CN4, CN5) ................................................................. 31
Chapter 3 Software Configuration..............33
Introduction ............................................................................................ 34
Connections for five standard LCDs .................................................... 34
Connections to Sharp LM64183P, LM64P89
(640 x 480 DSTN MONO LCD) .................................................. 34

Connections to PLANAR EL
(640 x 480 AD4 EL) ..................................................................... 35
Connections to Toshiba LTM10C042
(640 x 480 TFT Color LCD)......................................................... 36
Connections to Sharp LM64C142
(640 x 480 DSTN Color LCD) ..................................................... 37
Connections to Toshiba LTM12C275A
(800 x 600 TFT Color LCD)......................................................... 38
Ethernet software configuration ........................................................... 39
Chapter 4 Award BIOS Setup ......................41
System test and initialization................................................................. 42
System configuration verification ................................................. 42
AWARD BIOS setup .............................................................................. 43
Entering setup ............................................................................... 43
Standard CMOS setup .................................................................. 44
BIOS features setup ...................................................................... 45
CHIPSET features setup ............................................................... 46
Power management setup.............................................................. 47
PnP/PCI Configuration ................................................................. 48
Integrated Peripherals ................................................................... 49
Load BIOS defaults....................................................................... 50
Change Password .......................................................................... 51
Auto detect hard disk .................................................................... 52
Save & exit setup .......................................................................... 52
Exit without saving ....................................................................... 52
Chapter 5 PCI SVGA Setup..........................53
Before you begin ..................................................................................... 54
Installation .............................................................................................. 54
Simultaneousdisplaymode.................................................................... 55
Sleepmode............................................................................................... 55
Driver installation .................................................................................. 56
Necessary prerequisites ................................................................ 56
Before you begin .......................................................................... 56
Windows setup .............................................................................. 57
Changing Display Drivers in Windows ....................................... 57
Changing Color Schemes ............................................................. 57
DOS Setup .................................................................................... 58
Changing Display Drivers in DOS .............................................. 59

Panning Drivers ............................................................................ 59
Linear Acceleration Drivers ......................................................... 59
Windows 95 Drivers Setup Procedure.................................................. 59
Windows NT Drivers Setup Procedure ................................................ 60
OS/2 Drivers Setup Procedure .............................................................. 61
Preliminary Steps .......................................................................... 61
Installing from Diskette................................................................. 61
Selecting Monitor Type ................................................................. 63
Selecting Screen Resolution/Refresh Rate.................................... 63
Installation Notes .......................................................................... 64
Chapter 6 Audio Setup.................................65
Introduction ............................................................................................ 66
DOS Utilities ........................................................................................... 66
Changing setting in DOS ............................................................. 66
Controlling volume in DOS ......................................................... 67
Driver Installation .................................................................................. 68
Before you begin ........................................................................... 68
Windows 3.1 drivers ..................................................................... 68
Windows 95 Drivers ..................................................................... 69
Chapter 7 PCI Bus Ethernet
Interface Setup.........................................71
Introduction ............................................................................................ 72
Installation of Ethernet Driver.............................................................. 72
Installation for MS-DOS & WINDOWS 3.1 ................................ 72
Installation for WINDOWS 95 ..................................................... 73
Installation for WINDOWS NT .................................................... 75
FurtherInformation ............................................................................... 77
Appendix A Programming the
Watchdog Timer.......................................79
Programmingthe Watchdog Timer ...................................................... 80

Appendix B Installing PC/104 Modules ......81
Installing PC/104 modules ..................................................................... 82
Appendix C Pin Assignments .....................85
CRT display connector (CN1)....................................................... 86
Flat panel display connector (CN2) .............................................. 87
PC/104 connectors (CN3, CN9) ................................................... 88
USB connectors (CN4, CN5)....................................................... 90
Fan power connector (CN6).......................................................... 90
Front panel connector (CN7) ........................................................ 91
CD audio connector (CN8) ........................................................... 92
Peripheral power connector (CN10) ............................................. 92
Ethernet 10BASE-T connector (CN11) ........................................ 93
IR connector (CN12)..................................................................... 93
Audio connector (CN13)............................................................... 94
Main power connector (CN14) ..................................................... 94
Keyboard and PS/2 mouse connector (CN15) .............................. 95
COM port connector (CN16) ........................................................ 96
IDE hard drive connector (CN17) ................................................ 98
Floppy drive connector (CN18) .................................................... 99
Parallel port connector (CN19)................................................... 100
ATX Power Feature Connector (CON1)..................................... 101
ATX Soft Power Switch Connector (CON2) .............................. 101
1st MB Memory Map........................................................................... 103
DMA Channel Assignments ................................................................ 103
IRQ mapping chart .............................................................................. 104
Appendix D Optional Extras......................105
Optional LCD Cables for 9.4" MONO, 10.4" TFT LCD Panel ...... 107
Optional USB cable .............................................................................. 107
Optional IrdA adapter ......................................................................... 107
Appdendix E Mechanical Drawing............109
PCM-5862E/EL Mechanical Drawing ................................................110

1
General Information
This chapter gives background information
on the PCM-5862E/5862EL
Sections include:
• Introduction
• Features
• Specifications
• Board layout and dimensions
CHAPTER

2PCM-5862E/EL User's Manual
Introduction
The PCM-5862E/5862EL is an all-in-one multi-media Pentium
processor-based single board computer (SBC) with a 16-bit audio
controller, a PCI SVGA controller, a PCI 100/10 base-T Ethernet
interface, and one PCI expansion slot. When using an Intel MMX
Pentium processor, the PCM-5862E/5862EL achieves outstanding
performance that surpasses any other SBC in its class. This
compact (only 5.75“ x 8”) unit offers all the functions of a single
board industrial computer, but still fits in the space of a 5.25“
floppy drive.
On-board features include 512 KB 2nd level cache, four serial
ports (three RS-232, one RS-232/422/485), one multi-mode
parallel (ECP/EPP/SPP) port, two USB (Universal Serial Bus)
ports, a floppy drive controller and a keyboard/PS/2 mouse
interface. The built-in high speed PCI IDE controller supports
both PIO and bus master modes. Up to two IDE devices can be
connected, including large hard disks, CD-ROM drives, and tape
backup drives.
The PCM-5862E/5862EL features power management to minimize
power consumption. It complies with the “Green Function”
standard and supports Doze mode, Standby mode and Suspend
mode. In addition, the board‘s watchdog timer can automatically
reset the system or generate an interrupt in case the system stops
due to a program bug or EMI.
Highly integrated multi-media SBC
The PCM-5862E/5862EL is a highly integrated multi-media SBC
that combines audio, video, and network functions on a single
computer board the size of a 5.25" floppy drive. It provides 16-bit
half-duplex, 8-bit full-duplex, integrated 3D audio and up to 1024
x 768 resolution @ 64K colors with 2MB display memory. Major
on-board devices adopt PCI technology to achieve outstanding
computing performance when used with Intel Pentium processors,
making the PCM-5862E/5862EL the world‘s smallest and most
powerful all-in-one multimedia board.

3Chapter 1 General Information
Features
• Accepts Intel MMX Pentium, AMD K6, and Cyrix 6x86MX,
IDT WinChip C6
• 32-bit PCI-bus SVGA/LCD controller supports LCD & CRT
display
• 100/10Base-T Ethernet interface, IEEE 802.3U compatible
• 16-bit audio interface, Sound Blaster Pro compatible
• 4 serial ports (three RS-232 and one RS-232/422/485)
• USB interface, PCI slot, and PC/104 connector for flexible
expansion capabilities
• Watchdog timer with jumperless selection
• Switching power for full range Pentium MMX level processors
Specifications
Standard SBC functions
•CPU: Intel Pentium MMX up to 233MHz
AMD K6, K6-2 up to 300MHz
Cyrix 6x86MX-PR166, PR200, PR233
IDT WinChip C6 up to 200MHz,
•BIOS: AWARD 256KB Flash BIOS, supports Plug&Play, APM
•Chipset: SiS 5571
•Green function: APM 1.1 compliant
•2nd level cache: On board 512 KB Pipelined Burst SRAM
•RAM: Two 72-pin SIMM sockets accept 8~128 MB EDO/FPM
DRAM
•Enhanced IDE interface: Supports 2 IDE devices
•FDD interface: Supports up to two FDDs (360K/1.2M/720K/
1.44MB/ 2.88MB)

4PCM-5862E/EL User's Manual
•Parallel port: One parallel port, supports SPP/EPP/ECP parallel mode
•Serial port: Fourserial ports with three RS-232(COM1,3,4)andone
RS-232/422/485(COM2).Allportswith16C550compatible UARTs.
•Watchdog timer: 63-level interval from 1 to 63 seconds.
Generates system reset or IRQ15. Jumperless selection and
software enabled/disabled.
•Keyboard/Mouse connector: 8-pin header connector for
keyboard and PS/2 mouse
•USB interface: Two USB connectors with fuse protection.
Compliant with USB Spec. Rev. 1.0
•PC/104 expansion: 104-pin 16-bit PC/104 module connector
•I/O bus expansion: One 32-bit PCI bus expansion slot
•Switch voltage regulator: To support a full range of processor
voltage requirements. A solution for processor overheating.
PCI SVGA/flat panel interface:
•Chipset: C&T 65550
•Display memory: 1 MB on-board memory, supports up to 2 MB
•Display type: Simultaneously supports CRT and flat panel (EL,
LCD and gas plasma) displays
•Display resolution: Supports non-interlaced CRT and LCD
display up to 1024 x 768 @ 256 colors with 1MB VGA memory
or 1024 x 768 @ 64 K colors with 2MB(PCM-5862E only)
Audio function: (PCM-5862E only)
•Chipset: ESS 1868 or 1869
•Audio controller: 16-bit codec, Sound Blaster Pro compatible
•Stereo sound: 8-bit full-duplex, 16-bit half-duplex integrated 3D
audio
•Audio interface: Microphone in, Line in, CD audio in; Line out,
Speaker L, Speaker R
•Power: Accepts +12 V source for improved audio quality

5Chapter 1 General Information
PCI Bus Ethernet Interface:
•Chipset: REALTEK RTL8139A PCI local bus Ethernet
controller
•Ethernet Interface: IEEE 802.3U compatible 100/10BaseT
interface. Includes software drivers & boot ROM
Mechanical and environmental
•Max. power requirements: 7A @ 5V (4.75V to 5.25V)
•Operating temperature: 0 to 60° C (32 to 140° F)
•Size: 203 mm (L) x 146 mm (W) (8" x 5.75")
•Weight: 0.32 kg (0.7 lbs.) (w/o package)
Board layout and dimensions
PCM-5862E/5862EL dimensions

6PCM-5862E/EL User's Manual

7Chapter 2 Installation
2
Installation
This chapter tells how to set up the PCM-
5862E/5862EL hardware, including
instructions on setting jumpers and
connecting peripherals, switches and
indicators. Be sure to read all the safety
precautions before you begin the installation
procedure.
CHAPTER

8PCM-5862E/EL User's Manual
Jumpers
The PCM-5862E/5862EL has a number of jumpers that allow you
to configure your system to suit your applications. The table below
lists the function of each of the board’s jumpers.
Jumpers
Label Function
JP1 CPU voltage setting
JP2 Pentium MMX enable/disable
J1 System/PCI clock setting
J2 System/PCI clock setting
J4 CPU frequency ratio setting
J5 M1 cache linear mode setting
J6 CMOS clear
J7 Buzzer enable/disable
J10 LCD power setting
J11 COM4 RI pin setting
J12 COM3 RI pin setting
J13 Watchdog timer action
J14 COM2 RS-232/422/485 setting
J15 COM2 RS-232/422/485 setting
J16 Audio power source setting
J17 ATX power enable/disable setting

9Chapter 2 Installation
Connectors
On-board connectors link the PCM-5862E/5862EL to external
devices such as hard disk drives, a keyboard, or floppy drives. The
table below lists the function of each of the board’s connectors.
Connectors
Label Function
CN1 CRT display connector
CN2 Flat panel display connector
CN3 PC/104 ISA-bus expansion
CN4 USB channel 1 connector
CN5 USB channel 2 connector
CN6 Fan power connector
CN7 Front panel connector
CN8 CD audio input connector
CN9 PC/104 ISA-bus expansion
CN10 Peripheral power connector
CN11 Ethernet 100/10Base-T connector
CN12 IR connector
CN13 Audio connector
CN14 Main power connector
CN15 Keyboard and PS/2 mouse connector
CN16 COM-port connector
CN17 IDE hard drive connector
CN18 Floppy drive connector
CN19 Parallel port connector
CON1 ATX feature connector
CON2 ATX soft power connector switch
Please refer to Appendix C for pin assignment.

10 PCM-5862E/EL User's Manual
Locating jumpers
J5
J6
J9
J10
J11
J12
J13 J14
JP2
J16
J4
JP1
J2
J1
J7
J15
J8

11Chapter 2 Installation
Locating connectors
CN6
CN14
CN13
CN11
CN8
CON2
CON1
CN15 CN19
CN17
CN18
CN12
CN16
CN9
CN10
CN7
CN4
CN5
CN2
CN1
CN3

12 PCM-5862E/EL User's Manual
Setting jumpers
You configure your card to match the needs of your application by
setting jumpers. A jumper is the simplest kind of electric switch. It
consists of two metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To
“close” a jumper you connect the pins with the clip. To “open” a
jumper you remove the clip. Sometimes a jumper will have three
pins, labeled 1, 2, and 3. In this case you would connect either pins
1 and 2 or 2 and 3.
The jumper settings are schematically depicted in this manual as
follows:
A pair of needle-nose pliers may be helpful when working with
jumpers.
If you have any doubts about the best hardware configuration for
your application, contact your local distributor or sales
representative before you make any changes.
Generally, you simply need a standard cable to make most
connections.
13
2
Open Closed Closed 2-3
Open Closed Closed 2-3
1