Sangean PR-D19 User manual

Version 1
中文
GB
PR-D19

1
Important safety instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not t into your outlet. Consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.

2
GB
11.
12.
13.
14.
15.
16.
17.
Only use attachments/accessories specied by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or when unused for
long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged. liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
To Reduce the Risk of Fire or Electric Shock, Do not Expose This
Appliance To Rain or Moisture.
The Shock Hazard Marking and Associated Graphical Symbol is
provided on the rear of unit.
Apparatus shall not be exposed to dripping or splashing and no
objects lled with liquids, shall be placed on the apparatus.

3
18.
19.
20.
Excessive sound pressure on ear- and headphones could impair
the hearing ability. Higher setting that idle on the equalizer leads to
higher signal voltages on the output for ear and headphones.
The power plug should be close to the radio, and easy to be
approached that during the emergency, to disconnect the power
from the radio, just unplug the power plug from the AC power slot.
Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnected device shall remain readily
operable.
FCC INFORMATION
The Federal Communication Commission Radio Frequency
Interference Statement includes the following paragraph:
The equipment has been tested and found to comply with the
limits for a Class B Digital Device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction,
may cause harmful interference to radio communication. However,
there is no grantee that interference will not occur in a particular
installation. If this equipment dose cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

4
GB
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Cautions to the user
Notice:
The changes or modifications not expressly approved by the party
responsible for compliance could voidthe user’s authority to operate the
equipment.
CAUTION:
To reduce the risk of the electric shock, do notm perform any servicing
other than that contained in the operating instructions unless you are
qualied to do so.

5

6
GB
Control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
K
J
I
H
G
F
E
D
C
B
A
16
17
18
L
Speaker
Buzzer alarm radio
Radio alarm radio
Band/Bandwidth/Step button
Power on indicator
LCD display
Power/Sleep button
Volume down button
Volume up button
Display/Mono/Clock set button
Tuning up/down button
Key lock switch
Preset button
Battery compartment
Telescopic aerial
Aux in socket
Headphone socket
DC IN socket
Icon display
Battery indicator
Stereo indicator
Bandwidth indicator
Buzzer alarm indicator
Radio alarm indicator
Key lock symbol
Sleep timer indicator/Snooze indicator
Preset indicator
Volume indicator
Frequency/Clock display
PM indicator
FM/AM indicator

7
Using the radio for the rst time
Battery operation
1. Remove the battery cover on the rear of the unit by pressing the
catch.
2. Insert four UM-3 (AA size) batteries into the spaces in the compartment.
3. Take care to ensure all batteries are inserted with correct polarity
as shown on the rear cabinet. Replace the battery cover.
4. Reduced power, distortion, “stuttering sound” and the battery
icon ashing on the display are all signs that the batteries need
replacing.
5. If the radio is not to be used for any extended period of time, it is
recommended that the batteries are removed from the radio.

8
GB
Using the AC power adaptor
The AC power adaptor required for this unit should be 6 volts DC at
1 A center pin positive.
Insert the adaptor plug into the DC socket on the left side of the
radio.
Plug the adaptor into a standard mains socket outlet.
Whenever the adaptor is used, the batteries are automatically
disconnected.
The AC adaptor should be disconnected from the main supply when
not in use.
Operating your radio - Search tuning AM / FM
1. Fully extend the antenna above the radio. Press the Power button
to switch on your radio.
2. Press the Band button to select the required band.
3. Press and hold the Tuning up/down button to start the search
tuning. Your radio will scan in an upwards direction (low frequency
to high frequency) or downwards direction (high frequency to low
frequency) and stop automatically when it finds a station of
sufcient strength.
4. To find other stations, press and release the Tuning Up/Down
buttons.
5. Adjust the volume by pressing the Volume up/down button to the
required setting.
Note:
To see time or frequency on the screen, press the Display button.

9
Manual tuning - AM / FM
1. Press the Power button to switch on your radio.
2. Press the Band button to select the required band. Fully extend
the antenna for best reception.
3. Press and release the Tuning up/down button to tune to a station.
The FM frequency will change in steps of 50/100kHz and AM
frequency will change in steps of 9/10kHz.
4. When the waveband end is reached the radio will recommence
tuning from the opposite waveband end.
5. Set the Volume using the Volume Up/Down buttons to the desired
settings.
Presetting stations
You may store your preferred AM/FM radio stations to the preset
stations (1 to 5). The procedure for setting preset Stations is
described below.
Note that the radios for AM (AM1/AM2) and FM (FM1/FM2) are
saved together in the preset stations so there are 20 of them. Your
preset stations will be preserved for 30 minutes when there is no
power supply from either the battery or the AC adapter.
1. Press the Power button to switch on your radio.
2. Tune to the required station as previously described.
3. Press and hold the required Preset button (1-5) until you hear a
beep sound and the display shows‘M1’ for example on the top right
corner. The station will be stored using the preset number. Repeat
this procedure for the remaining presets as you wish.
4. Preset stations which have already been stored may be overwritten
by following the above procedure if required.