Sangean WR-2 User manual

Revision 1
GB
WR-2A

1
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.
Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does not fit
into your outlet. consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specied by the manufacturer.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

GB
2
Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged. liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
To Reduce the Risk of Fire or Electric Shock, Do not Expose
This Appliance To Rain or Moisture.
The Shock Hazard Marking and Associated Graphical Symbol
is provided on the bottom panel of unit.
Apparatus shall not be exposed to dripping or splashing and no
objects lled with liquids, shall be placed on the apparatus.
Excessive sound pressure on ear- and headphones could impair
the hearing ability. Higher setting that idle on the equalizer leads
to higher signal voltages on the output for ear and headphones.
The power plug should be close to the radio, and easy to be
approached that during the emergency, to disconnect the power
from the radio, just unplug the power plug from the AC power slot.
Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnected.
12.
13.
14.
15.
16.
17.
18.
19.
20.

3

GB
4
Speaker
Light button
Band button
LCD display
Preset buttons
Power On / Off / Sleep button
Tuning control knob
Volume / tone control
IR sensor
Menu button
Mono button
Radio alarm button
Buzzer alarm button
Nap button
Info button
Headphone socket
AC power cord socket
12V DC input socket (ideal for vehicles / boats)
REC out socket
AUX IN socket
External / Internal antenna switch
External F-type FM antenna terminal
External AM antenna terminal (USA version only)
Controls
2
3
1
5
7
20
19
18
17
16
15
14
13
12
11
10
9
4
6
8
21
22
23

5
Power On / Off / Sleep button
Nap button
Select button
Info button
Preset button
Mute button
Light button
Tuning up / down button
Tone control button
Volume button
Menu button
Radio alarm button
Buzzer alarm button
Band button
Remote control
a
h
f
d
i
j
k
l
m
n
g
e
c
b

GB
6
Frequency / Time / Station display
Radio / Buzzer alarm indicator
Daylight Saving Time (DST)
Sleep / Snooze status
RDS indicator
Stereo indicator
Memory preset
Aux In level attenuation
Display icons
B
C
E
G
D
F
A
H

7
Remote control functions
Many functions of the WR-2 radio can be operated using the
remote control. Some operations require a longer press of the
button.
In this case simply keep your finger held on the remote control
button for 2-3 seconds until the display on the radio shows that the
command has been accepted.
Before the rst operation: please remove the small transparent
foil from the battery holder to activate the battery.

GB
8
Remote control battery replacement
4. Replace the battery holder.
IMPORTANT:
The batteries should not be exposed to excessive heat such as
sunshine, re or the like. After use, disposable batteries should if
possible be taken to a suitable recycling center. On no account
should batteries be disposed of by incineration.
Warning
KEEP OUT OF REACH OF CHILDREN
[The remote control supplied with] This product contains a coin/
button cell battery. Swallowing may lead to serious injury or death.
Severe burns can occur within 2 hours of ingestion.
Keep batteries out of reach of small children. Coin cell batteries can
be accidentally ingested. If ingested, these batteries may leak harmful
contents causing chemical burns, perforation of soft tissue, and in
severe cases may cause death. Coin batteries must be removed
immediately if swallowed. Seek medical attention immediately, if you
or your doctor suspects that a battery has been ingested.
1. Open the battery holder by pulling
the holder out in direction shown.
2. Remove battery from holder.
3. Replace battery (CR2025 or equivalent)
ensuring that the positive side of the
battery faces you with holder positioned
as shown.

9
Power your radio
AC operation
Before you plug the AC cord into the radio, be sure the AC voltage
is correct. Insert the plug on the end of the supplied power cord
into the AC power socket on the back of the radio.
DC operation
For outdoors use, you can power the radio by using 12V DC input
socket from a DC power supply (example, from the power supply of
vehicles or boats). An AC power adaptor with 1 Ampere and center
positive in polarity can also power the radio in house.
Using the radio for the rst time
1. Place your clock radio on a at surface.
2. Insert the adaptor plug into the AC socket located on the rear of
your radio.
Manual clock setting
1. Press Menu button and the display will show ‘CLOCK SET’.
2. Press the Tuning control knob to enter the clock setting.
3. Rotate the Tuning control knob to select the desired hour and
press the Tuning control knob to conrm the hour setting. Now the
minute digit will ash.
4. Rotate the Tuning control knob to adjust the minutes and press
the knob to conrm the setting. Now the clock setting is completed.