Sanijet FB2-S115 User manual

PIPELESSWHIRLPOOL
FOOT BATH
OWNER’S MANUAL
Model: FB2-S115

2
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ………………………………………………....3
WARNINGS …………………………………………………………………………………..4
INSTRUCTIONS PRIOR TO USE ……………………………………………………….…5
GROUNDING INSTRUCTIONS ……...……………………………………….……………5
HOW TO USE …………………………………………………………………..…………….6
HOW TO DRAIN AND CLEAN ………….…………………………………….…………...7
HOW TO STORE THE FOOT BATH.…………………………………………………...…9
LIMITED WARRANTY ……………………………………………………………………..9
HOW TO OBTAIN SERVICE ……………………………………………………………..10
PRODUCT CERTIFICATIONS …………………………………………………………...10

3
SANIJETPipelessWhirlpool Foot Bath
Thank you for purchasing the revolutionary PipelessWhirlpool Foot Bath. The Pipeless
Whirlpool Foot Bath joins SANIJET’s luxurious PipelessWhirlpool Baths and Pipeless
Whirlpool Pedicure Sinks in providing excellent hydrotherapy, quiet operation and the ability for
quick, easy and certified cleanliness.
SANITATION CERTIFICATION: The National Sanitation Foundation (nsf.org) confirmed
that SANIJET’s Pipelesssystem can be completely cleaned and disinfected, even if system
cleaning has been neglected.
For more information about SANIJET’s Pipeless Whirlpool Baths and Pipeless Whirlpool
Pedicure Sinks, please visit our website at www.sanijet.com
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING: When using an electrical appliance, basic precautions should
always be followed.
Read and follow all instructions before using this foot bath.
DANGER – To reduce the risk of electrical shock:
1. Always unplug this appliance from the electrical outlet and store the power cord when
not in use.
2. DO NOT use this appliance while bathing or in a shower.
3. DO NOT place or store this appliance where it can fall or be pulled into water.
4. DO NOT reach for any electrical object that has fallen into water. Unplug immediately.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS:
1. DO NOT leave this appliance unattended when it is connected to a power source.
2. DO NOT carry this appliance by the supply cord or use the cord as a handle.
3. DO NOT drop or insert anything into any jet opening.
4. DO NOT operate this unit without the complete jet assembly installed or without water
filled to the water level indicator above the jets.
5. DO NOT overfill.
6. DO NOT stand on or in the foot bath. Use only while seated.
7. Use the SANIJET Pipeless Foot Bath only for its intended purpose: a fill and drain,
appliance for foot and ankle hydro massage. DO NOT use attachments not recommended
by the manufacturer.

4
WARNINGS:
1. Risk of accidental injury or drowning: Children, invalid or disabled persons should not
use a hydro massage foot bath without adult supervision.
2. To avoid injury, exercise care when entering or exiting the foot bath.
3. Risk of electric shock: DO NOT permit electric appliances (e.g. hair dryer, lamp,
telephone, radio, television, etc.) to be within 5 feet (1.5m) of this appliance.
4. Keep the cord away from heated surfaces.
5. Connect this appliance only to a properly grounded outlet. (See Grounding Instructions
below.) Do not remove, modify or immerse the integral GFCI on the power cord.
6. Risk of hypothermia and possible drowning: Water temperature in excess of 104º F (38
ºC) may be injurious to your health. Check and adjust water temperature before use.
7. RISK OF ELECTRIC SHOCK: Disconnect from electrical supply before servicing.
8. Hydrotherapy should be pleasant and comfortable. Should you experience any pain or
discomfort while using the foot bath, discontinue use immediately and consult your
physician.
9. Consult your physician if you are diabetic, have poor circulation, if any area of your feet
or legs is inflamed, has an open wound or if you have any other questions about whether
you should be using hydro massage equipment.
10. Unless thoroughly cleaned after each use, bath residue will buildup within the jets and on
the surface area of any whirlpool foot bath, which can promote the growth of bacteria.

5
INSTRUCTIONS – Prior to Use
WARNING: When using electrical products, basic precautions should always be followed
including the following:
1) IMPORTANT: Read complete instructions before use. Each Pipeless
Whirlpool Foot Bath arrives ready for use.
2) This unit requires a 115 volt, 60 Hertz, 2 Amp service and is provided with a 10’ cord
with an integral Ground Fault Circuit Interrupter (GFCI) and NEMA 5-15P electrical
plug. A grounded electrical outlet is required.
3) Remove the foot bath from the carton and retain the shipping carton and packing material
to reuse in case service becomes necessary. DO NOT lift the foot bath by its handle or
electrical cord.
3) Immediately upon receipt, inspect the entire unit for any obvious damage BEFORE
using. Should inspection reveal any damage or defect in the finish, do not use the foot
bath. SANIJET® Corporation’s responsibility for shipping damage ceases upon delivery
of the product in good order to the carrier. Refer any claim for damage to the carrier.
4) All foot bath units are factory tested for proper operation and watertight connections prior
to shipping. Note: Prior to use, the foot bath must be filled with water and operated to
check for leaks that may have resulted from shipping damage or mishandling.
GROUNDING INSTRUCTIONS
This unit must be grounded. The integral GFCI should be tested on a routine basis. To test the
GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power
should be restored. If the GFCI fails to operate in this manner, there is a ground fault, indicating
the possibility of electrical shock. DO NOT USE THE UNIT. Disconnect the unit and have the
problem corrected by a qualified service representative or an electrician before using.

6
HOW TO USE
1. Fill the unit with water at the desired temperature above the jets to the water level
indicator. A fill hose with a connector to attach to a typical sink spout is included or the
unit can be filled with the use of a container.
2. Move the unit to the place where it will be used and be sure that it is on a level, solid
floor. Note: The front two casters have locking mechanisms to prevent the unit from
moving during use. Be sure the locking mechanisms are disengaged before attempting to
move the unit. A handle is built into the top of the unit for easy maneuverability. Before
moving the unit filled with water, place the two removable lids on the tank to prevent
water from splashing onto the floor. (See Illustration #1.)
Illustration #1
3. Plug the unit into a grounded electrical outlet.
4. To activate or deactivate this appliance, press the ON/OFF button.
5. Bath additives (including oil based products) can be used in a SANIJET Pipeless Foot
Bath, since their residue can be easily cleaned. CAUTION: Use only low foaming
additives.
6. You should always be in a seated position when putting your feet in or removing them
from the foot bath. WARNING: NEVER STAND IN THE FOOT BATH.
7. During use of the foot bath the front lid can be used as a foot rest as well as assist in
maintaining water temperature and reduce splashing.

7
HOW TO DRAIN AND CLEAN
To maintain your SANIJET®Pipeless Whirlpool Foot Bath at a maximum level of hygiene,
thoroughly clean the tub shell and jets after each use with a nonabrasive antibacterial cleaner,
rinse thoroughly, and dry completely. See page 8 for complete cleaning procedure. NEVER use
abrasive cleaners on the foot bath.
Procedure to Drain the Foot Bath:
1. Turn off the foot bath by pushing the ON/OFF button.
2. Unplug the foot bath from the electrical outlet and store the cord.
3. Put both removable lids on the tank before moving the foot bath to the area where the
tank will be drained and then remove the lids.
4. Place the Discharge Pump on the flat round
surface in the bottom of the foot bath. (See
Illustration #2)
5. Extend the hose connected to the Discharge
Pump to the area where the water is to be
drained (sink). Use the suction cup provided
to secure the hose to the side of the sink and
turn on the discharge pump by plugging the
pump’s power cord into a grounded circuit.
(See Illustration #3)
6. When the foot bath appears to be empty, continue running the
pump while removing it from the interior of the foot bath and
place it in the sink or chosen draining area. As soon as the
pump and hose are both fully in the sink unplug the power cord
to turn off the discharge pump. Fresh water can be used to
rinse out the tank during the draining procedure. (See
Illustration #3.)
**Do not leave the pump running in the draining area or in a dry
foot bath for more than a few seconds because it may result in
damage to the discharge pump.
**The power cord cannot be replaced; in case of any damage to
the power cord the entire discharge pump must be replaced.
Illustration #2
Illustration #3

8
Procedure to Clean the Foot Bath:
STEP 1:
Preparation, Jet Removal, and Cleaning
•Drain the Footbath according to draining procedure.
•Rotate the Jet Assemblies counterclockwise and remove
them from the Jet Cases in the Footbath.
•Disassemble the Jet Assemblies (three pieces) for further
cleaning.
•Spray the Jet Assembly Pieces, Footbath Interior,
and Jet Cases with *Cleaner / Disinfectant.
•Use a clean cloth to clean the Jet Assembly pieces,
removing any visible soil.
•Scrub all surfaces of the Footbath and Jet Cases.
•Rinse all surfaces with tap water
STEP 2:
Disinfection and Re-Assembly
•Spray the Jet Assembly pieces, Jet Cases and Foot Bath
until thoroughly wet with *Cleaner / Disinfectant
and allow them to set for 1 minute.
•Rinse disinfectant from all surfaces.
•Dry the Jet Assembly pieces, Jet Cases, and the
Footbath, with a clean cloth.
•Reassemble Jet Assemblies and reinsert them
into Jet Cases, rotate them in a clockwise manner to
secure them in position.
Detergent / Disinfectant Selection:
*SANIJET recommends the use of an EPA registered cleaner / disinfectant with tuberculocidal,
germicidal, pseudomonacidal, Fungicidal and Virucidal efficacy. Do not use abrasive cleaners on the
Pedicure Basin or Jet Assemblies. SANIJET suggests *DISPATCHHospital Cleaner Disinfectant with
Bleach as a suitable cleaner disinfectant for use with the above procedure.
Illustration #4
Removing Jet Assembly from
Jet Case
Illustration #5
Jet Assembly
Dispatch® - EPA Reg. No. 56392-7; EST. No.
62801-MI-001. Kills bacteria and viruses in 1 minute
and TB in 30 seconds.

9
HOW TO STORE THE FOOT BATH
1. Replace the jet assemblies into the jet casings by reversing the procedure shown in
Illustration #4.
2. Store the power cord inside the recess cavity at the base of the foot bath.
3. Store the fill hose and Discharge Pump inside the tank or in another location.
4. Replace both lids.
5. Store away from direct exposure to sunlight to prevent discoloration of the foot bath.
T
TW WO O ( (2 2) ) Y YE EA AR R L LI IM MI IT TE ED D W WA AR RR RA AN NT TY Y
PORTABLE FOOT BATH
S
Sc co op pe e: : S SA AN NI IJ JE ET T w wi il ll l p pr ro ov vi id de e t th he e p pa ar rt ts s a an nd d l la ab bo or r a at t i it ts s f fa ac ct to or ry y t to o r re ep pa ai ir r a an ny y d de ef fe ec ct t i in n m ma at te er ri ia al ls s o or r
w
wo or rk km ma an ns sh hi ip p, , u un nl le es ss s e ex xc cl lu ud de ed d b be el lo ow w, , r re ep po or rt te ed d i in n w wr ri it ti in ng g t to o S SA AN NI IJ JE ET T w wi it th hi in n t th he e w wa ar rr ra an nt ty y p pe er ri io od d. .
S
SA AN NI IJ JE ET T m ma ay y e el le ec ct t t to o r re ep pl la ac ce e t th he e p pr ro od du uc ct t o or r t th he e a af ff fe ec ct te ed d c co om mp po on ne en nt t i if f i it t d de et te er rm mi in ne es s i in n i it ts s s so ol le e d di is sc cr re et ti io on n
t
th ha at t t th he e d de ef fe ec ct t c ca an nn no ot t b be e s sa at ti is sf fa ac ct to or ri il ly y r re ep pa ai ir re ed d. . W Wa ar rr ra an nt ty y P Pe er ri io od d: : T Th he e w wa ar rr ra an nt ty y p pe er ri io od d i is s t tw wo o ( (2 2) ) y ye ea ar rs s
a
af ft te er r t th he e d da at te e t th he e p pr ro od du uc ct t i is s f fi ir rs st t p pu ur rc ch ha as se ed d f fo or r u us se e a an nd d n no ot t f fo or r r re es sa al le e. . S SA AN NI IJ JE ET T m ma ay y r re eq qu ui ir re e y yo ou u t to o
e
es st ta ab bl li is sh h t th he e d da at te e o of f p pu ur rc ch ha as se e b by y i in nv vo oi ic ce e o or r o ot th he er r d do oc cu um me en nt ta at ti io on n s sa at ti is sf fa ac ct to or ry y t to o S SA AN NI IJ JE ET T. . E Ex xc cl lu us si io on ns s: :
T
Th hi is s w wa ar rr ra an nt ty y d do oe es s n no ot t c co ov ve er r t th he e m me et ta al ll li ic c d dr ra ai in n p pl la at te e, , f fa ad di in ng g f fr ro om m e ex xp po os su ur re e t to o d di ir re ec ct t s su un nl li ig gh ht t, , f fr re ei ig gh ht t
d
da am ma ag ge e, , o or r m mi is sh ha an nd dl li in ng g, , a ab bu us se e, , m mi is su us se e, , n ne eg gl le ec ct t, , a ac cc ci id de en nt t o or r n na at tu ur ra al l d di is sa as st te er r. . S Sh hi ip pp pi in ng g: : Y Yo ou u a ar re e
r
re es sp po on ns si ib bl le e f fo or r s sh hi ip pp pi in ng g t th he e p pr ro od du uc ct t t to o S Sa an ni ij je et t f fo or r w wa ar rr ra an nt ty y s se er rv vi ic ce e a an nd d f fo or r r re et tu ur rn n s sh hi ip pp pi in ng g c ch ha ar rg ge es s a af ft te er r
r
re ep pa ai ir r o or r r re ep pl la ac ce em me en nt t. . C Cl la ai im ms s: : R Re ep po or rt t t th he e p pr ro ob bl le em m t to o S SA AN NI IJ JE ET T’ ’s s c cu us st to om me er r s se er rv vi ic ce e d de ep pa ar rt tm me en nt t
B
BE EF FO OR RE E t th he e w wa ar rr ra an nt ty y p pe er ri io od d e ex xp pi ir re es s. . T Th he e a ad dd dr re es ss s i is s 1 14 46 61 1 S So ou ut th h B Be el lt tl li in ne e R Ro oa ad d, , S Su ui it te e 1 10 00 0, , C Co op pp pe el ll l, ,
T
Te ex xa as s 7 75 50 01 19 9. . T To ol ll l F Fr re ee e N Nu um mb be er rs s: : T Te el le ep ph ho on ne e 8 87 77 7- -9 93 34 4- -0 04 47 77 7; ; F Fa ax x 8 87 77 7- -8 83 34 4- -0 04 47 77 7. . T To ol ll l N Nu um mb be er rs s: :
T
Te el le ep ph ho on ne e 9 97 72 2- -7 74 45 5- -2 22 28 83 3; ; F Fa ax x 9 97 72 2- -7 74 45 5- -2 22 28 85 5. . E E- -m ma ai il l: : c cu us st to om me er rs sv vc c@ @s sa an ni ij je et t. .c co om m.
. U Un na au ut th ho or ri iz ze ed d
R
Re ep pa ai ir r: : A An ny y c co om mp pl le et te ed d o or r a at tt te em mp pt te ed d r re ep pa ai ir r o or r a al lt te er ra at ti io on n b by y a an ny yo on ne e o ou ut ts si id de e o of f S SA AN NI IJ JE ET T’ ’s s f fa ac ct to or ry y n no ot t
e
ex xp pr re es ss sl ly y a au ut th ho or ri iz ze ed d i in n w wr ri it ti in ng g b by y S SA AN NI IJ JE ET T w wi il ll l V VO OI ID D t th hi is s w wa ar rr ra an nt ty y. . D De ea al le er r W Wa ar rr ra an nt ti ie es s: : N No o d de ea al le er r o or r
d
di is st tr ri ib bu ut to or r h ha as s a an ny y a au ut th ho or ri it ty y t to o b bi in nd d S SA AN NI IJ JE ET T t to o a an ny y c ch ha an ng ge es s o or r a ad dd di it ti io on ns s t to o t th hi is s w wa ar rr ra an nt ty y. . L Li im mi it ta at ti io on n
O
On n D Da am ma ag ge es s: : T To o
t
th he e f fu ul ll le es st t e ex xt te en nt t a al ll lo ow we ed d b by y l la aw w, ,
S
SA AN NI IJ JE ET T
d
di is sc cl la ai im ms s a an nd d e ex xc cl lu ud de es s l li ia ab bi il li it ty y
f
fo or r
c
co on ns se eq qu ue en nt ti ia al l a an nd d i in nc ci id de en nt ta al l d da am ma ag ge es s i in nc cl lu ud di in ng g, , b bu ut t n no ot t l li im mi it te ed d t to o, , l lo os st t p pr ro of fi it ts s, , l lo os ss s o of f b bu us si in ne es ss s
r
re ep pu ut ta at ti io on n, , o ou ut t o of f p po oc ck ke et t e ex xp pe en ns se es s, , d da am ma ag ge e t to o p pr ro op pe er rt ty y o ot th he er r t th ha an n t th he e w wa ar rr ra an nt te ed d p pr ro od du uc ct t, , m me en nt ta al l a an ng gu ui is sh h
a
an nd d p pu un ni it ti iv ve e d da am ma ag ge es s. . T Th he e m ma ax xi im mu um m a am mo ou un nt t o of f S SA AN NI IJ JE ET T’ ’s s l li ia ab bi il li it ty y w wi il ll l b be e t th he e a am mo ou un nt t y yo ou u p pa ai id d f fo or r t th he e
p
pr ro od du uc ct t. . S So om me e s st ta at te es s l li im mi it t o or r d do o n no ot t a al ll lo ow w t th he e e ex xc cl lu us si io on n o or r l li im mi it ta at ti io on n o of f i in nc ci id de en nt ta al l o or r c co on ns se eq qu ue en nt ti ia al l
d
da am ma ag ge es s, , s so o s so om me e o or r a al ll l o of f t th he es se e l li im mi it ta at ti io on ns s m ma ay y n no ot t a ap pp pl ly y t to o y yo ou u. . S St ta at te e L La aw w R Ri ig gh ht ts s: : T Th hi is s w wa ar rr ra an nt ty y
g
gi iv ve es s y yo ou u s sp pe ec ci if fi ic c l le eg ga al l r ri ig gh ht ts s, , a an nd d y yo ou u m ma ay y a al ls so o h ha av ve e o ot th he er r r ri ig gh ht ts s t th ha at t v va ar ry y f fr ro om m s st ta at te e t to o s st ta at te e. . T TH HE E
D
DU UR RA AT TI IO ON N O OF F A AN NY Y I IM MP PL LI IE ED D W WA AR RR RA AN NT TI IE ES S U UN ND DE ER R S ST TA AT TE E L LA AW W, , I IN NC CL LU UD DI IN NG G T TH HE E I IM MP PL LI IE ED D
W
WA AR RR RA AN NT TI IE ES S O OF F M ME ER RC CH HA AN NT TA AB BI IL LI IT TY Y A AN ND D F FI IT TN NE ES SS S F FO OR R A A P PA AR RT TI IC CU UL LA AR R P PU UR RP PO OS SE E, , I IS S
L
LI IM MI IT TE ED D T TO O T TH HE E W WA AR RR RA AN NT TY Y P PE ER RI IO OD D D DE ES SC CR RI IB BE ED D A AB BO OV VE E. . S So om me e s st ta at te es s d do o n no ot t a al ll lo ow w l li im mi it ta at ti io on ns s
o
on n h ho ow w l lo on ng g a an n i im mp pl li ie ed d w wa ar rr ra an nt ty y l la as st ts s, , s so o t th hi is s l li im mi it ta at ti io on n m ma ay y n no ot t a ap pp pl ly y t to o y yo ou u. .

10
HOW TO OBTAIN SERVICE
For Customer Service contact:
SANIJET Customer Service Department
Toll Free Tel. [phone]
Toll Free Fax [phone]
E-MAIL: [email protected]
SANIJETCorporation
1461 South Beltline Road, Suite 100
Coppell, Texas 75019
Tel. [phone]; Fax [phone]
www.sanijet.com
Product Certifications:
The Pipeless system is manufactured with CUL recognized components (motors, jets and
controls).
2004, SANIJET®Corporation
Printed in U.S.A.
75027/Rev. 09/2004
NSF Protocol P182
Pipeless Hydrotherapy