Sanitaire RSCS280A User manual

1
Document No. 98-1133F4 • September 2019 • ©2019 Atlantic Ultraviolet Corporation®
Read and Follow All Safety Instructions. Save These Instructions.
Installation, Operation & Maintenance
Model RSCS280A
Extensive Product Information Available at:
Ultraviolet.com
BuyUltraviolet.com
Owner’
s Manual
Owner’
s Manual

2
TABLE OF CONTENTS
SAFETY WARNINGS .......................................................................................................................................................................3
SAFETY INSTRUCTIONS ..............................................................................................................................................................3
SAFETY LABELING........................................................................................................................................................................3
CAUTION...........................................................................................................................................................................................3
PRODUCT APPLICATION .............................................................................................................................................................4
ConstruCtion .................................................................................................................................................................................................... 4
PrinCiPle of oPeration .................................................................................................................................................................................... 4
limitation of use.............................................................................................................................................................................................. 5
UNPACKING .....................................................................................................................................................................................5
INSTALLATION ...............................................................................................................................................................................5
fixture PlaCement .........................................................................................................................................................................5
oPeration and monitoring Controls............................................................................................................................................6
MAINTENANCE...............................................................................................................................................................................6
lamP installation, rePlaCement or Cleaning .......................................................................................................................... 7-8
intake filter ..................................................................................................................................................................................9
Cleaning of eleCtrostatiC filter ..................................................................................................................................................9
Breakage ........................................................................................................................................................................................9
disPosal of merCury added lamPs ...............................................................................................................................................9
OPTIONAL ACCESSORIES .........................................................................................................................................................10
TROUBLESHOOTING ..................................................................................................................................................................10
TECHNICAL SPECIFICATIONS.................................................................................................................................................11
REPLACEMENT PARTS...............................................................................................................................................................11
USER ASSISTANCE ....................................................................................................................................................................... 12
Patent notiCe...............................................................................................................................................................................12
WARRANTY & PRODUCT REGISTRATION ...........................................................................................................................12
These instructions generally describe the installation, operation and maintenance of the SANITAIRE®Room Air Sanitizer Model
RSCS280A. Questions that are not specifically answered by these instructions should be directed to the Factory.
Atlantic Ultraviolet Corporation®takes all possible precautions when packaging equipment to prevent damage. Carefully inspect and
report all damages immediately. Do not install damaged equipment.
Follow all instructions on any labels or tags. Carefully inspect all packing materials before discarding to prevent the loss of
accessories, mounting hardware, spare parts or instructions.
The information and recommendations contained in this publication are based upon data collected by the
Atlantic Ultraviolet Corporation®and are believed to be correct. However, no guarantee or warranty of
any kind, expressed or implied, is made with respect to the information contained herein. Specifications
and information are subject to change without notice.

3
SAFETY INSTRUCTIONS
To guard against injury, basic safety precautions should be observed, including the following:
1. Read and follow ALL safety instructions.
Avoid exposure to direct or reflected germicidal ultraviolet rays. Germicidal ultraviolet
rays are harmful to the eyes and skin.
2. Intended for indoor use only.
3. Do not alter design or construction.
4. Do not use this fixture for other than its intended purpose, as described in this manual.
5. Do not override safety interlock.
6. Do not mount under any source of moisture or condensation, such as humidifiers, cooling coils, etc.
7. Do not remove any labels or devices.
8. Do not operate without proper electrical ground.
9. Do not operate the fixture if there is visible or suspected damage to the fixture or, if applicable, there is damage
to power cord and/or plug.
10. Keep inlet and outlet, of the blowers, clean and clear of debris.
11. Do not operate without the access door securely closed on the unit.
12. Stay clear of blowers, or other moving parts that can cause injuries.
13. Utility power supplied, to the fixture, MUST match power requirements listed on the unit label.
14. Always disconnect power to the unit before performing any service or maintenance.
15. Read and follow all notices and warnings on the fixture.
16. SAVE THESE INSTRUCTIONS.
SAFETY LABELS CAUTION
Danger Label: Ultraviolet Radiation
(00-0195A2)
Danger Label: Hazardous Voltage
(00-0197A2)
It is the user’s responsibility to determine and validate
the suitability of this equipment for use in the user’s
system or process.
No warranty or representation is made by the manufacturer
with respect to suitability or performance of this equipment
or to the results that may be expected from its use.
The user should periodically inspect, clean as necessary
and confirm the presence and good legibility of the product
safety labels. Contact the factory for replacement labels in
the event that any of the labels are missing or illegible.
UV
ULTRAVIOLET
RADIATION
Protect eyes and skin from
direct and reflected radiation.
Turn off and disconnect
power before servicing.
HAZARDOUS
VOLTAGE
DANGER

00-0196A1
ULTRAVIOLET RADIATION
Protect eyes and skin from direct and reflected radiation.
Turn off and disconnect power before servicing.
HAZARDOUS VOLTAGE
DANGER

00-0199A1
UV
WARNING

No. 00-0195A2
UV
ULTRAVIOLET
RADIATION
Protect eyes and skin
from direct and reflected
radiation.
DANGER

Turn off and disconnect
power before servicing.
HAZARDOUS
VOLTAGE
No. 00-0197A2
AIR & WATER
Part No. 00-0195A2 (2.75 x 1.5) Part No. 00-0197A2 (2.75 x 1.5)
AIR
Part No. 00-0198A1 (1.25 x 3)
This fixture is designed for use with germicidal
ultraviolet lamps and must be installed in
compliance with competent technical directions
so that the users eyes and bare skin will not be
subjected to injurious radiation.
WARNING

No. 00-0198A1
AS OF MAY 2002 THESE LABELS ARE BEING USED ON ALL OUR PRODUCTS
Part No. 00-0196A1 (2.5 x 2.25)
Part No. 00-0199A1 (5 x 1.33)
SAFETY WARNINGS
• All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.
• The following conventions are used to indicate and classify precautions in this manual and on product safety labeling. Failure to
observe precautions could result in injury to people or damage to property.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
This symbol/pictorial is used to identify the need to
wear protective gloves.
!
Caution indicates a POTENTIALLY
hazardous situation, which, if not avoided,
MAY result in minor or moderate injury.
Caution used without the safety alert symbol
indicates a potentially hazardous situation, which,
if not avoided, may result in property damage.
This symbol/pictorial is used to identify an
ULTRAVIOLET LIGHT hazard.
This symbol/pictorial is used to identify an ELECTRICAL
SHOCK or ELECTROCUTION hazard.
Warning indicates a POTENTIALLY
hazardous situation, which, if not avoided,
COULD result in death or serious injury.
This symbol/pictorial is used to identify the need to
wear approved ultraviolet blocking eye wear. This symbol/pictorial is used to identify the need to wear
approved ultraviolet blocking face shield.
This symbol/pictorial is used to identify components
which must not be disposed of in trash.
Danger indicates an IMMINENTLY
hazardous situation, which, if not avoided,
WILL result in death or serious injury.

4
PRODUCT APPLICATION
ConstruCtion
The SANITAIRE®Room Air Sanitizer Model RSCS280A consists of:
• STER-L-RAY ®Germicidal Ultraviolet Lamps deliver ultraviolet energy at the specific wavelength of 254 nanometers (nm).
This wavelength is highly effective against microbes including: virus, bacteria, and mold spores.
Germicidal ultraviolet rays are harmful to eyes and skin; avoid exposure of direct or reflected
germicidal ultraviolet rays without approved ultraviolet blocking face shield and protective covering (such as gloves,
long sleeves with no gaps between cuffs and gloves).
• A SureliteTM Electronic Ballast capable of operating at 120v 50/60 Hz. Other power supplies may be available. Contact
factory for specifics.
• A polished reflector, whose design and specular aluminum construction maximizes ultraviolet intensity within
the exposure chamber.
• Power Cord - For 120v AC 50/60Hz single-phase standard household current, a NEMA 5-15, three-prong plug is provided for
a properly grounded outlet. (Consult factory for other plug types)
• PromateTM Promate permanent, washable, electrostatic intake filter is electrostatically charged to trap up to 94% of dust and
allergens that pass through the filter. Filters are made with a heavy duty aluminum frame and a special weaved filter for years
of filtration.
• A louvered exhaust, which restricts ultraviolet radiation from passing into the room, protecting the room’s occupants from
ultraviolet exposure.
• Indicator LED’s work in pairs to provide a visual indication if a lamp has failed.
• All electronics and wiring are housed in an enclosure constructed of stainless steel. Stainless steel construction provides
strength, durability, and will withstand most harsh environments.
• An interlock safety switch. The interlock switch interrupts power to the sanitizer, when the access door is opened from
the lamp /exposure chamber.
PrinCiPle of oPeration
The SANITAIRE®Room Air Sanitizer is categorized as a germicidal ultraviolet fixture that utilizes germicidal ultraviolet lamps
that are completely enclosed within an exposure chamber and is safe for use in a clean, dry environment. The SANITAIRE®
effectively destroys airborne microbes including: bacteria, mold and virus in enclosed spaces.
The SANITAIRE®design has been carefully conceived to provide germicidal ultraviolet exposure for air disinfection. The
dosage, as it applies to ultraviolet disinfection, is a function of time, and the intensity, of ultraviolet radiation, to which the air
is exposed. The exposure time, in seconds, is the total time it takes the air to move through the ultraviolet field, produced by the
germicidal lamps.
All components are mounted in a stainless steel frame. Access to the lamp/exposure chamber is gained through the interlocked,
access door. Fixture operation can be monitored from the base panel.
The operation of the SANITAIRE®Room Air Sanitizer Model RSCS280A is as follows:
1. Air is drawn into the fixture through the the louvered filter panel.
2. The air is forced into the exposure chamber, where it is irradiated by the germicidal ultraviolet lamps.
3. LED indicator lights provide positive indication of operation of germicidal ultraviolet lamps.
4. The purified air exits the fixture, through the louvered exhaust panel, located at the opposite end of the fixture.
Figure 1 – SANITAIRE®Room Air Sanitizer Model RSCS280A Operation

5
limitation of use
Overexposure to germicidal ultraviolet rays will result in the irritation of the eyes and reddening of
the skin. For that reason, it is of the utmost importance that your ultraviolet application be carefully planned and
implemented so as to avoid exposure, of personnel, to direct or reflected ultraviolet rays.
The American Conference of Governmental Industrial Hygienists (ACGIH) has established that the ultraviolet radiant exposure
incident for unprotected eyes or skin should not exceed 0.2 microwatts per square centimeter (µW/cm2) at 254 nanometers (nm)
for an eight (8) hour period. (“2004 TLVs®and BEIs®”)
UNPACKING
IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY
EQUIPMENT: SAFETY GLASSES OR A FACE SHIELD, AS WELL AS GLOVES.
• Remove the SANITAIRE®Room Air Sanitizer Model RSCS280A from its shipping carton.
• Atlantic Ultraviolet Corporation®takes all possible precautions when packaging this fixture to prevent damage. Carefully
inspect the sanitizer, power cord, if applicable, for damage. Report all damage immediately.
• Do not assemble or operate if there is any damage, visible or suspected.
• STER-L-RAY ® Germicidal Ultraviolet Lamps are packed separately, to ensure maximum protection for the lamps. Keep the
lamps aside until ready for installation.
• Carefully inspect all packing materials to prevent the loss of accessories, mounting hardware, spare parts or instructions.
• Do not discard packing materials until fixture is assembled and check out is complete.
The SANITAIRE®Model RSCS280A Room Air Sanitizer includes:
• 1 - Model RSCS280A – 120v 50/60Hz
• 1 - (4) High Output STER-L-RAY ®Germicidal Ultraviolet Lamps (may be packed within the unit)
INSTALLATION
fixture PlaCement
The SANITAIRE®Model RSCS280A fixture is recommended for use in rooms with suspended “T-Bar” ceilings. Access to the
room does not need to be controlled while the fixture is operating. The exposure chamber, of the SANITAIRE®fixture, protects
the room’s occupants from ultraviolet exposure by restricting ultraviolet radiation from passing into the room.
To ensure safe and proper use: (see Figure 2)
• The SANITAIRE®Model RSCS280A Room Air Sanitizer MUST be installed by qualified professionals so that local and
national building and electrical codes are fully complied with.
Failure to adequately support this equipment could result in serious injury or even death.
• The SANITAIRE®Model RSCS280A has 4 suspension points. The suspension method chosen should be structurally
adequate to support the weight of the unit independently from any one of these suspension points (unit weight can be found in
the equipment specification).
• Using an individual cable or chain for each of the (4) suspension locations are the best method to ensure the unit is adequately
secured in place. Never use a single cable or chain to hold fixture by the (4) suspension locations.
• Never attempt to support or suspend this unit on the ceiling tile track system.
• Remember it is the equipment user’s responsibility to ensure an adequate and safe installation of this equipment and the
safety of room occupants.
• It is recommended that the SANITAIRE®Model RSCS280A be wired to a wall switch to control on and off operation.

6
OPERATION AND MONITORING CONTROLS
The SANITAIRE®is designed to operate with minimal operator supervision. Fixture operation is monitored from the Base Panel.
Lamp Operation Indicators: Provide positive indication, when lit, of each germicidal lamp operation. Lamp Operation LEDs,
which are not lit, indicate faulty germicidal lamps or ballasts. Lamp Operation LED position, in the LED array, is relative to the
germicidal lamp position in the exposure chamber, aiding in the location of the faulty lamp(s) or ballast(s).
MAINTENANCE
Always disconnect power to the fixture before performing any service or maintenance.
• The SANITAIRE®Model RSCS280A is designed to operate with a minimal amount of maintenance.
• A regular cleaning cycle of the germicidal lamps, interior, and intake filter MUST be established, and carefully maintained,
based on inspection and experience. The frequency of cleaning will vary with the conditions surrounding each installation. It
is recommended that the ultraviolet lamps be cleaned at least once every three (3) months.
• The STER-L-RAY ®Germicidal Ultraviolet Lamps used in the SANITAIRE®have a manufacturer’s rated average effective
life of 13,000 hours. Lamps may operate longer than their rated effective life, but the reduction in ultraviolet output will make
it impractical to use past the manufacturer’s rated life. For maximum efficiency lamp replacement is recommended every
13,000 hours of operation or about one (1) year of continuous use.
• Unless lamp replacement is due to failure or breakage, it is recommended that all lamps be replaced at the same time.
• The SANITAIRE®Model RSCS280A is equipped with a safety interlock switch, which will shut down the germicidal lamps
when the Access Door is opened.
Do not override the safety interlock switch. Operation of the fixture with the interlock switch
overridden and the Access Door open will expose personnel to direct or strongly reflected germicidal ultraviolet rays.
Germicidal ultraviolet rays are harmful to the eyes and skin.
Figure 2

7
lamP installation, rePlaCement or Cleaning
IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY
EQUIPMENT: SAFETY GLASSES OR A FACE SHIELD, AS WELL AS GLOVES.
Always disconnect power to the fixture before performing any service or maintenance.
Ultraviolet lamp(s) are easily damaged and may cause injury if broken. Exercise care when handling.
1. Disconnect power to the fixture.
2. Open access door, by unlocking the two (2) latches.
Opening of the SANITAIRE®access cover will cause the interlock switch to interrupt power to the
lamps and blower. Do not attempt to bypass or circumvent the interlock switch or its safety feature.
3. Starting from the front, remove each STER-L-RAY ® lamp by holding the lamp by the base and carefully pull the lamp away
from the connector, while removing pressure off the STER-L-RAY ® lamp from the end supports. (See Figure 3)
4. Once the lamp is clear from the connector, carefully lift STER-L-RAY ® lamp away from the far end support, and remove
STER-L-RAY ® lamp from the unit. (See Figure 4)
5. Repeat until all STER-L-RAY ® lamps have been removed from the unit.
Figure 4Figure 3
6. Moisten a clean, lint-free cloth with denatured alcohol and clean STER-L-RAY ®lamps.
7. When STER-L-RAY ®lamps have been removed, cleaned, and safely set aside, remove any loose dust or dirt from the
interior of the fixture with a soft dry cloth, or vacuum.
8. To remove any dust, dirt, fingerprints, smears, etc, from the outer surfaces of the SANITAIRE®Room Air Sanitizer,
moisten a clean, lint-free cloth with denatured alcohol and wipe down the unit. Buff out any streaks left from the cleaning,
using a soft dry cloth.

8
9. When installing the new lamps, carefully examine the pin configuration on the lamps base to ensure that the lamp is installed
correctly into the lamp connector (See Figure 5, which shows the lamp connector and Figure 6, which shows the lamp base,
below).
10. Begin installing the STER-L-RAY ® lamps from one side and continue to the next until all STER-L-RAY ® lamps have
been installed.
11. Hold the STER-L-RAY ®lamp by the base and carefully push the STER-L-RAY ®lamp into the connector. (See Figure 7)
12. Once the STER-L-RAY ® lamp is securely seated into the connector, carefully push the STER-L-RAY ® lamp into the end
support. (See Figure 8)
13. Repeat until all STER-L-RAY ® lamps have been installed into the unit.
Avoid exposure to direct or reflected germicidal ultraviolet rays. Germicidal ultraviolet
rays are harmful to the eyes and skin.
14. Close and lock access door.
15. Restore power to the fixture.
16. Verify operation by viewing Lamp Operation Indicators (LEDs). If the sanitizer is not operating properly, go to
“Troubleshooting” section.
Figure 6Figure 5
Figure 8
Figure 7

9
intake filter
• The SANITAIRE®Room Air Sanitizer Model RSCS280A is fitted with a, washable, electrostatic air filter. DO NOT apply
oil, or adhesive sprays to the filter.
• In most applications, regular vacuuming will maintain peak performance of PromateT M Electrostatic Filter; periodically
flushing electrostatic filter with clean water is recommended whenever vacuuming fails to restore a clean appearance.
• The PromateT M Electrostatic Filter may be cleaned repeatedly without loss of efficiency. The frequency of cleaning will vary
with the conditions surrounding each installation.
Cleaning of eleCtrostatiC filter
IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY
EQUIPMENT: SAFETY GLASSES OR A FACE SHIELD, AS WELL AS GLOVES.
Always disconnect power to the fixture before performing any service or maintenance.
1. Disconnect power to the fixture.
2. Unlatch and open access cover.
3. Remove PromateT M filter from the housing.
4. Vacuum the upstream side first, and repeat on the discharge side. (Skip to step 7 unless washing filter.)
Do not use a high velocity water stream to clean the filter. A high velocity stream may destroy the
filter’s internal fibers.
5. To wash PromateT M filter, flush thoroughly with clean water, either by immersing or with a fine spray in the direction
opposite to the airflow. If the filter is contaminated with heavy grease concentrations, wash filter with a detergent solution.
NOTE: Follow all manufacturer’s instructions and precautions for handling detergents. The filter should be rinsed
thoroughly with clean water.
6. Shake off any excess water from PromateTM filter and let dry.
7. Replace PromateTM filter into the housing, with airflow direction label pointing into the electrical enclosure.
8. Close and re-latch access louver.
9. Restore power to the fixture.
10. Verify operation by viewing Lamp Operation Indicators (LEDs). If the sanitizer is not operating properly, go to
“Troubleshooting” section.
Breakage
Broken Quartz is SHARP.
Wear protective gloves when handling broken ultraviolet lamp(s). In the event of breakage, DO NOT use a
household vacuum cleaner to pick up quartz fragments. Sweep up debris into a plastic bag and dispose of properly.
DisPosal of merCury aDDeD lamPs
Germicidal ultraviolet lamps, like standard fluorescent lamps contain small amounts of mercury. Mercury added
lamps should not be placed in the trash. Dispose of properly. For further information regarding the disposal and
recycling of lamps containing mercury, along with Federal and State requirements visit LampRecycle.org. For more
information on STER-L-RAY ®germicidal ultraviolet lamps, visit Ultraviolet.com or BuyUltraviolet.com.

10
OPTIONAL ACCESSORIES
1. ArmorLiteTM Lamp Safety Shield: A protective coating applied to STER-L-RAY ®Germicidal Ultraviolet Lamps, ensuring
protection by eliminating the dangers associated with fragments of broken glass and mercury contamination.
2. Zenith™UV-C Detector: A sensitive, hand-held, self-contained battery operated ultraviolet meter that can be used for:
• Monitoring UV-C Germicidal Lamp Intensity & Aging
• Measuring UV-C Germicidal Fixture Leakage.
3. PromateTM Safety Glasses: Safety eyewear MUST be used as general-purpose safety protection and for additional shielding
from ultraviolet rays.
4. PromateTM Face Shield: Lightweight visor with adjustable headgear provides eye and face protection from germicidal
ultraviolet rays.
5. SENTINEL®Lamp Operation Indicator: Monitors individual lamp operation, in any location up to 100 feet from the
SANITAIRE®Room Air Sanitizer. Cables are also available in 25, 50, and 100 foot lengths.
For more information and purchasing contact our offices, weekdays between 8:30 am and 5:00 pm Eastern time, at:
Atlantic Ultraviolet Corporation®, 375 Marcus Boulevard, Hauppauge, New York, 11788
Tel: [phone] • Fax: [phone] • Email: [e-mail] • Website: Ultraviolet.com – BuyUltraviolet.com
TROUBLESHOOTING
Always disconnect power to the unit before performing any service or maintenance.
Use personal protection equipment, such long sleeves with no gaps between cuffs and gloves, and
ultraviolet resistant face shield, if troubleshooting SANITAIRE ®.
IMPORTANT: This unit is to be serviced ONLY by qualified, and appropriately trained and/or licensed personnel.
Table 1 – Troubleshooting
Problem Possible Cause Corrective Action
Unit not operating.
No electrical power. Verify that the unit is connected to a live power source.
Power connection to fixture is loose
or disconnected. Verify power connection to fixture is fully engaged.
Internal blower(s) not
functioning.
Loose power connection. Confirm connection to blower; connections are tight
and make full contact.
Faulty blower motor. Replace blower motor.
Two STER-L-RAY ®
germicidal lamps
not operating
SureliteT M Ballast not functioning.
Swap both lamps, with known good lamps.
If good lamps still do not operate, locate
corresponding ballast and replace.
STER-L-RAY ®Germicidal lamp
not operating. Swap both lamps, with known good lamps.
STER-L-RAY ®Germicidal lamp not
properly seated.
Confirm lamps are installed correctly and are seated
making full contact with lamp socket.
All STER-L-RAY ®
germicidal lamps
not operating.
STER-L-RAY ®Lamps not installed. Install lamps.
Interlock switch open. Confirm access door is closed and latched.
Interlock switch faulty. Replace interlock switch.
If the above measures fail to correct the problem(s), contact our Application Specialists. Contact options can be found in the
“User Assistance” section of this manual, located on the back page.

11
TECHNICAL SPECIFICATIONS
Table 2 – Technical Specifications
Blower Capacity: (Cubic Feet per Minute) 280 CFM
Nominal Fixture Capacity j: (Cubic Feet per Minute) 210 CFM
Max Treatment Capacity: (Cubic Feet per Hour) 12,600 ft3/ hr
Max Room Size @ 3 Air Changes/Hour: (Cubic Feet) 4,200 ft3
Max Room Size @ 4 Air Changes/Hour: (Cubic Feet) 3,150 ft3
Max Room Size @ 5 Air Changes/Hour: (Cubic Feet) 2,520 ft3
Max Room Size @ 6 Air Changes/Hour: (Cubic Feet) 2,100 ft3
Dimensions
Length: (Inches) 46-5/8”
Width: (Inches) 22-1/8”
Height: (Inches) 9-7/16”
Electrical
Voltage: (v) 120v
Amperage: (A) 4.2A
Lamp Data
Power Consumptionk: Watts per Lamp 65W
Power Consumptionk: Watts for 4 Lamps 260W
Ultraviolet Outputl: Watts per Lamp 22W
Ultraviolet Outputl: Watts for 4 Lamps 88W
Weight Pounds: (lbs.) 64 lbs.
jFixture capacity incorporates an estimated allowance for airflow friction loss across filter and fixture.
kWattage is lamp watts only and does not include ballast loss.
lUltraviolet output at 254nm at 100 hours and 80 °F (approximate).
All specifications, dimensional data, etc. are approximate and subject to change without notice.
REPLACEMENT PARTS
Table 3 – Replacement Parts
Description QTY. Part No.
STER-L-RAY ®Germicidal Ultraviolet Lamp 4 05-0497
SureliteTM Electronic Ballast, 50/60Hz 2 10-0138
Lamp Socket and Plate Assembly 2 40-0740A
Interlock Switch, SPDT 1 35-0008A
PromateTM Air Filter, Electrostatic, Washable 1 40-0062A
PromateTM Air Filter, Disposable 1 40-1850
PromateTM Blower, 140CFM, 120v 60Hz 2 40-1079B
Eyebolt, 8-32 x 1” Long with Hex Nut 4 50-0157
Lead Cord, 120v 1 35-1100-R
Other replacement parts are available. Consult the Factory for specific requirements.

12
USER ASSISTANCE
Atlantic Ultraviolet Corporation®
makes every effort to ensure that the
SANITAIRE®Model RSCS280A
is a product of superior quality and
workmanship. This manual describes
the installation, operation and
maintenance of the SANITAIRE®
Model RSCS280A.
Please read and become familiar with
the contents of this manual before
installing or using this unit. If after
reading the manual you still have
questions, or concerns, regarding the
installation or use of this unit, contact
our offices, weekdays between 8:30 am
and 5:00 pm Eastern Time, at:
Atlantic Ultraviolet Corporation®
375 Marcus Boulevard
Hauppauge, New York, 11788
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Website: Ultraviolet.com
BuyUltraviolet.com
WARRANTY & PRODUCT REGISTRATION
We warrant this product to the original owner to be free from defects in material and workmanship when installed in
accordance with Atlantic Ultraviolet Corporation®specifications for a period of time as follows:
UV Water Purifier Chambers – Type 316 stainless steel chambers will have a Twelve (12) year Limited Warranty on the stainless
steel chamber, from the date of original purchase while the Type 304 stainless steel chambers will have a Six (6) year Limited
Warranty on the stainless steel chamber.
UV Air Disinfection Housing – Three (3) year Limited Warranty on the metal housing, from the date of original purchase.
Ballasts – Three (3) year Limited Warranty, from the date of original purchase.
UV Lamps, Monitoring Devices, Optional Accessories, and Other Parts – One (1) year Limited Warranty from the date
of original purchase.
Within the warranty period we shall repair or replace such products, which are returned to us with shipping charges prepaid and which
are determined by us to be defective. This warranty will not apply to any product, which has been subjected to misuse, negligence or
accident; or misapplied; or modified; or repaired by unauthorized person; or improperly installed. Warranty will be null and void if
any of the product’s original labels are removed. This Limited warranty excludes the cost of labor.
The Buyer shall inspect the product promptly after receipt and shall notify us at our main office in writing of claims, including claims
of breach of warranty, within thirty (30) days after the Buyer discovers or should have discovered the facts upon which the claim is
based. Failure of the Buyer to give written notice of a claim within the time period shall be deemed to be a waiver of such claim.
The provisions of the above warranty are our sole obligation and exclude all other remedies or warranties, expressed or implied,
including warranties of merchantability and fitness for a particular purpose, whether or not purposes or specifications are described
herein. We further disclaim any responsibility whatsoever to the customer, or to any person for injury to person, damage to, or loss
of property or value caused by any product which has been subjected to misuse, negligence, accident; or modified or repaired by
unauthorized persons; or improperly installed.
Under no circumstances shall the Company be liable for any incidental, consequential or special damages; losses or expenses arising
from the contract for this product, or in connection with the use of, or inability to use, our product for any purpose whatsoever.
Be sure to register your product and validate purchase within 30 days –registration is simple and will take less than 2 minutes to do.
NOTE – failure to register your purchase may jeopardize warranty.
Go to Ultraviolet.com and scroll down to the bottom of the page, under “Trust” click the “Warranty Registration Form”, complete and
click “Submit”. Or click on “Warranty Registration PDF” to download the warranty registration card as a PDF, complete and mail to
us at 375 Marcus Boulevard, Hauppauge, NY 11788, or simply fax to 631-273-0771. If you prefer to register by phone, please call
631-273-0500 and our customer service staff will be glad to assist you.
For your convenience, record the following information below. The model and serial number can be found on a label located
on the SANITAIRE®Model RSCS280A. Keep this manual, along with proof of purchase, handy when
contacting our offices.
Purchased From: Date:
Model: Serial No.:
Patent notiCe
No attempt has been made to determine the patent status of applications illustrated or described in this publication. Inclusion in
this publication of any design or method of use, which may be patented, is not to be construed as promoting or sanctioning
unauthorized use.